Use and Care Manual

10. Next place the pot (K) onto the hangers
located in the popper unit. Hold the pot
cantered at approximately a 70 degree
angle as illustrated here. Place the two
hanger bars into the slots on the hanger.
Do Not force. Make sure the hangers are
well seated before swinging the axle
shaft up to the motor. The roller pin will
fit into the niche on the motor and will
help align the gears. Check to make sure
the gears properly meshed together
before starting the motor.
Stirrer
Pot Heater
Warmer
I
L
M
J
7. The glass door (J) simply slides into the two anchor hinges
on the popping unit. (I) The door is easy to remove for
cleaning.
Note: The metal handle
should align with the
magnetic latch on the
popping unit (I).
8. Align the two bottom tabs
on the Stainless Steel tilt
door (L) with the slots on
the bottom platform of the
popping unit. The side
panels will bend in slightly
to maneuver past the
corner rails.
9. The “Old Maids” drawer (M) slides into
the opening at the bottom of the popper
unit.
Note: The “Old Maids” drawer is designed to catch
un-popped kernels that fall through the
sized holes. Occasionally empty the drawer.
Debris that may not make it into the drawer
should be removed before replacing drawer
tray. Loose debris can prevent the drawer
from shutting properly.
Note: Hand bar should be on the door
side facing you.
CAUTION The pot on this popper will
become extremely hot when in
use.
DO NOT Remove or install pot until it is
completely cooled off.
DO NOT Load pot before installing or while
hot. Avoid steam released from
the pot. It can scald and cause
severe burns.
KEEP CHILDREN AWAY FROM HOT POT!
Pot Heater
Stirrer
Warmer
11. The last step is to plug the pot into the
outlet located on the ceiling of the popper
cabinet. Before plugging the pot into the
cabinet outlet, make sure the pot is seated
properly on the hangers, the gear shaft is
properly aligned and all the switches are in
the off position.
NEVER plug the pot cord directly into a
electrical outlet.
Now that you have assembled your popper, you are ready to make popcorn the way it’s made in theaters
and concessions everywhere. Below are instructions on how to operate your popper. Read them
carefully to make yourself a popping expert. When operated correctly your popper will give you many
years of service and happiness.
Note: The upper cabinet is equipped with rubber
feet and can be used separate from
storage cabinet on a sturdy counter top.
Do Not place the popper near a heat source such
as a stove or oven. Allow a minimum of
12” of open space on all sides.
Do Not place this unit near water or a water
source.
Do Not use electric circuits that do not meet
minimum requirement as specified.
Stirrer
Pot Heater
Warmer
The Warmer switch operates the light in
the back left corner of the popper unit and
the warming element in the bottom tray.
The warmer can be left on for extended
periods of time. The two elements work
together to keep the popcorn fresh and
warm. Ready to Eat!
Warning: Do not dump liquid toppings
onto popped corn while in the popper. It
will cause a huge mess and result in
much clean-up time. Remove popcorn to
a serving bowl before adding wet
toppings.
The Stirrer switch operates the stirrer
located inside the pot. Make sure it is
free of obstruction and the axle gear
and the motor gear are properly
seated before turning the Stirrer
switch on. If pot is not cleaned at
a p p r o p r i a t e i n t e r v a l s o r
recommended popping oils are not
used, the bottom of the pot will gum
with burnt oil and debris. If the stirrer
sounds the least bit strained, switch
off immediately and solve the
problem.
The Pot Heater switch operates the
heating element in the bottom of the
pot. (Kettle) It is engineered to deliver
the perfect temperature for popping
Popcorn. It is extremely hot! Care
should be taken when in close
proximity of the pot. When pot is hot
use heat resistant gloves. Only touch
the safety knob on the pouring handle.
SUCCESS!
WARMER
Stirrer
Pot Heater
Page 8Page 7