Installation manual for all 24”, 30”,36” and 48’’ ranges
WARNING: If the information in this manual is not followed exactly, a fire or explosion may result causing property damage, personal injury or death. • Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. • WHAT TO DO IF YOU SMELL GAS: – Do not try to light any appliance. – Do not touch any electrical switch; – Do not use any phone in your building. – Immediately call your gas supplier from a neighbor’s phone.
CONTENTS 4 6 14 16 18 19 25 26 27 28 29 26 30 31 32 33 Warnings & Important Safety Instructions Dimensions Specifications Technical data Clearance Dimensions (Proximity to Cabinets) Electrical & Gas Requirements Gas Requirements General Information Installation/ Door Removal Leg Installation/Adjustments/Alignments Anit-tip Device Installation Connecting Gas & Electrical Final Preparation Performance Checklist Service & Registration Warranty U.S.A.
Warnings & Important Safety Instructions • Before beginning, please read these instructions completely and carefully. • DO NOT remove permanently affixed labels, warnings, or plates from product.This may void the warranty. • All local and national codes and ordinances must be observed. Installation must conform with local codes or in the absence of codes, the National Fuel Gas Code ANSIZ223.1 INFPA54.
Warnings & Important Safety Instructions DANGER CHEMICAL HAZARD To avoid risk of property damage and/or personal injuryor death; this appliance is not too be used as a heating source. • Benzene is a chemical which is part of the gas supply to this cooking product, which is consumed in the flames during combustion. Exposure to a small amount of benzene is possible if a gasleak occurs. Formaldehyde and soot are by products of incomplete combustion.
Dimensions 35" 7/8 min - 37" 5/16 max 2" 1" 3/8 24” SUPERIORE Gas Ranges 23 " 2 3" 7/ 8 2" 3 / 16 Note: Unit shown with island trim. Note: All gas ranges are equipped with spacer on the back (25/64) to prevent over heating of the wall.
Dimensions 24” SUPERIORE Gas Ranges 29" 7/8 23" 7/8 2" 1" 3/8 1" 3/8 2" 26" 7/8 2" 1" 3/8 3/8" 2" 27/64 3/8" 2" 6/8 1" 1/2 23" 1" 11/32 2" 6/8 min 4" 1/4 max 5" 5" 9/16 1" 11/32 2" 3/8 35" 15/32 min - 36" 7/8 max 2" 1/8 2" 3/16 5" Electricity 2" 1/8 35" 7/8 min - 37" 5/16 max 25" 33" Gas |7
Dimensions 35" 7/8 min - 37" 5/16 max 2" 1" 3/8 30” SUPERIORE Ranges 23 " 2 8 7/ " 9 2" 3 / 16 Note: Unit shown with island trim. Note: All gas ranges are equipped with spacer on the back (25/64) to prevent over heating of the wall.
Dimensions 30” SUPERIORE Ranges 29" 7/8 29" 7/8 2" 1" 3/8 1" 3/8 5" Electricity 2" 1/8 35" 7/8 min - 37" 5/16 max 25" 33" Gas 2" 5" 9/16 2" 26" 7/8 3/8" 2" 6/8 1" 1/2 23" 1" 11/32 2" 6/8 min 4" 1/4 max 2" 3/16 1" 3/8 3/8" 2" 27/64 35" 15/32 min - 36" 7/8 max 2" 1/8 5" 1" 11/32 2" 3/8 |9
Dimensions 35" 7/8 min - 37" 5/16 max 2" 1" 3/8 33" 36” SUPERIORE Ranges 23 3 " 8 7/ 5" 2" 3 / 16 Note: Unit shown with island trim. Note: All gas ranges are equipped with spacer on the back (25/64) to prevent over heating of the wall.
Dimensions 36” SUPERIORE Ranges 35" 7/8 1" 3/8 2" 1" 3/8 35" 7/8 Electricity 2" 1/8 35" 7/8 min - 37" 5/16 max 5" 2" 25" 33" Gas 2" 5" 9/16 2" 26" 7/8 3/8" 2" 6/8 1" 1/2 23" 1" 11/32 2" 6/8 min 4" 1/4 max 2" 3/16 1" 3/8 3/8" 2" 27/64 35" 15/32 min - 36" 7/8 max 2" 1/8 5" 1" 11/32 2" 3/8 | 11
Dimensions 35" 7/8 min - 37" 5/16 max 2" 1" 3/8 48” SUPERIORE Ranges 23 4 8 7/ 7" " 2" 3 / 16 Note: Unit shown with island trim. Note: All gas ranges are equipped with spacer on the back (25/64) to prevent over heating of the wall.
Dimensions 48” SUPERIORE Ranges 47" 7/8 47" 7/8 2" 4" 1" 3/8 5" 25" 33" Gas 2" 1/8 Electricity 2" 5" 9/16 2" 26" 7/8 1" 11/32 4" 2" 3/8 35" 15/32 min - 36" 7/8 max 2" 1/8 2" 3/16 3/8" 2" 6/8 1" 1/2 23" 1" 11/32 2" 6/8 min 4" 1/4 max 5" 3/8" 2" 3/8 | 13
Specifications Technical data Burners - injectors and volume, range 24‘‘ (mod. R...241...) Natural 4’’ LP/Propane 11’’ By-pass Inj. W BTU/h Inj. W BTU/h Ø W BTU/h Medium burners 117 - 6500 70 - 6500 34 - 1300 Large burner 155 - 11000 93 - 11000 44 - 2700 ring Power burner Ext. Int. ring 137 (2) 80 - 18000 82 (2) 50 - 18000 65 - 4700 Power burner Ext. ring with simmer Int.
Specifications Technical data Burners - injectors and volume, ranges 36‘‘(mod. R...361... and R...362...) Natural 4’’ LP/Propane 11’’ By-pass Inj. W BTU/h Inj. W BTU/h Ø W BTU/h Small burner (*) 92 - 3600 56 - 3600 28 - 1100 Medium burner (**) 117 - 6500 70 - 6500 34 - 1300 155 - 11000 93 - 11000 44 - 2700 - 18000 65 - 4700 - 18000 60 27 - 4700 Large burner ring Power burner Ext. Int. ring 137 (2) 80 - 18000 82 (2) 50 Power burner Ext.
Clearance Dimensions 24’’/30’’/36’’/48’’ 3 0’’ 6’’ 3 • This range may be installed directly adjacent to existing 36” (91.4 cm) high base cabinets. 24’’ IMPORTANT: The side trim MUST be 3/8” (0.95 cm) above the adjacent base cabinet countertop. This can be accomplished by raising the unit adjusting the legs. 13" min 30" • The range CANNOT be installed directly adjacent to sidewalls, tall cabinets, tall appliances, or other side vertical surfaces above 36”(91.4 cm) high.
Clearance Dimensions 36’’ 30’’ 24’’ 13" 3/8" min 18" min 30" The bottom of a standard hood should be 30” (76.2 cm) min. to 36” (91.4 cm) max to above the countertop. This would typically result in the bottom of the hood being 66” (167.6 cm) to 72” (182.9 cm) above the floor. Refer to the range hood installation instructions for additional information. These dimensions provide for safe and efficient operation of the hood.
Electrical & Gas Requirements Electrical Requirements Check your national and local codes regarding this unit. This range requires120VAC/60 Hz; 4 ft. (121.9 cm), 3-wire cord with grounded 3-prong plug attached to unit. See “Electrical Connection” section for grounding instructions. Must be fused seperately from any other circuit.
Gas Requirements TO INSTALL PRESSURE REGULATOR 1 - Remove the 2 covers on the back by unscrewing the 3 screws indicated at pag 15 step 1 an 2. 2 - Take from the top of packaging the parts shown in the picture below to assemble the pressure regulator. 3 - Screw the assembled pressure regulator on the range like shown on picture below. Pay attention to the vertical alignement of the same pressure regulator. 4 - Screw the assembled pressure regulator on the range like shown in picture below.
Gas Requirements To perform the following operation is necessary to have eavy access to the back the range. While performing this plese note that the range must not be connected to the power and or gas lines. 3 - Fit the elbow on the regulator. Put the gasket, in it. REMOVE 1 - Remove the main back cover unscrewing the two screws. 4 - Connect the regulator to the manifold and re-install the main back cover. 2 - Remove the gas regulator back cover unscrewing the single screw.
Gas Requirements Flexible Connections: If the unit is to be installed with flexible couplings and/or quickdisconnect fittings, the installer must use a heavy-duty AGA design-certified flexible connector or at least1/2” (1.3 cm) ID NPT (with suitable strainreliefs) in compliance with ANSI Z21.41and Z21.69. operate with one of these gas/pressure as indicated in the labels affixed on the appliance, package and Instruction booklet. To convert the regulator for use with other liquid propane LP gas: 1.
Gas Requirements STEP 2: SURFACE BURNERS To replace the nozzles of the surface burners, lift up the burners and unscrew the nozzles shipped with the range using a 7 mm (sochet wrench). Replace nozzles using the conversion set supplied with the range or by a Tecno authorized parts warehouse. Each nozzle has a number indicating its flow diameter printed on the body. Consult the table on “Specifications Technical data” paragraph for matching nozzles to burners.
Gas Requirements Replace the nozzle using the conversion set supplied with the range or by a Tecno authorized parts warehouse. Each nozzle has a number indicating its flow diameter printed on the body. Consult the table on “Specifications Technical data “ paragraph for matching nozzles to burners. Air adjustment is not needed. For 24” and 30” range’s STEP 4 (FORALL-GAS RANGES ONLY): BROILER BURNER Loosen the 2 screws on left and right sides and pull out the burner from its support burner from its support.
Gas Requirements The tip of the spark plug or thermocouple must fully overlap at least the first gas emission hole of the burner. After performing all these visual checks, reinstall the bottom panel of the oven compartment and proceed to setting the minimum for each burner. STEP 6: MINIMUM FLAME ADJUSTMENT WARNING! These adjustments should be made only for use of the appliance with natural gas. For use with liquid propane gas, the By-pass screw must be fully turned in a clockwise direction.
General Information READ AND FOLLOW ALL WARNING AND CAUTION INFORMATION WHEN INSTALLING THIS APPLIANCE. • All openings in the wall behind the appliance and in the floor under the appliance must be sealed. • Do not obstruct the flow of combustion and ventilation air. CAUTION Avoid any damage to oven vents. The vents need to be un obstructed and open to provide proper airflow for optimal oven performance.
Installation/Door removal NOTICE DO NOT use the handle or oven door to lift the oven. DO NOT lift or carry the door by the handle. Removing the door must be done by your dealer, a qualified licensed plumber, or certified gas installer. 1 Door Removal 1)- Open the door completely. Place the pins, supplied with unit, in pin hole. For personal safety, ONLY use pins supplied with the unit. 2 2)- Grasp the door as indicated in the photos below and turn up until you perceive the block.
Leg Installation/Adjustments/Alignment Superiore ranges must be used only with the legs properly installed. Four height adjustable legs, assembled under the bottom of the range Four height adjustable legs are delivered with the range in the polysterene container situated over the appliance. Before installing the legs, position the appliance near its final location as the legs are not suitable for moving the appliance over long distances.
Anti-tip Device Installation WARNING TIPPING HAZARD: To reduce the risk of property damage or personal injury; install anti-tipping device provided in accordance with the installation instructions in this document. Device must be engaged properly to prevent product from tipping over. TIPPING Kit enclosed with the range. Mark and drill holes where the bracket will be located. Measure from floor to the anti-tip bar located in a slit on the back of the range.
Connecting Gas & Electric DANGER GAS LEAK HAZARD To avoid risk of personal injury or death; leak testing of the appliance must be conducted according to the manufacturer’s instructions. Before placing appliance in operation, always check for gas leaks with soapy water solution. • DO NOT USE AN OPEN FLAME TO CHECK FOR GAS LEAKS. Connect gas and electrical. Before placing appliance in operation, always check for gas leaks.
Performance Checklist A qualified installer should carry out the following checks: The low flame should light at every port. Check top burner ignition. Push and turn the knob “Full on“ position. Check oven bake function bake burner on full power. Check convection broil function broil burner at full power. Check convection fans function convection fans comes on when switch is turned on. Convection fans do not operate when broils working.
Service & Registration Only authorized replacement parts may be used in performing service on the appliance. All servicing should be referred to a qualified technician. Contact SUPERIORE 1-844-322-2111, for the nearest service parts distributor in your area or write to: CUSTOMERCARE@TECNOSPA.IT Record the information indicated below. You will need it if service is ever required. The model and serial number can be found by looking in the last page of this booklet.
WARRANTY U.S.A & CANADA Please record your model (MOD) and serial number (S/N) below for future reference. For your convenience, a label containing this information is supplied with this booklet.
Electric diagram 24” - 30” 4 burners all gas ranges | 33
Electric diagram 36” 6 burners all gas ranges 34 |
Electric diagram 36”4 burners and griddle all gas ranges | 35
Electric diagram 48” 4 induction areas, electric griddle and 2 gas burners 36 |
Electric diagram 48” 6 gas burners and electric griddle all gas ranges | 37
Electric diagram 30” 4 burners dual fuel s.c.
Electric diagram 36” 6 burners dual fuel s.c.
Electric diagram 48” 6 burners and electric griddle dual fuel s.c.
Electric diagram 48” 6 burners and electric griddle dual fuel s.c.
Electric diagram 30’’/36”/48” dual fuel s.c.
appliances are proudly designed and handcrafted in Gualtieri, Italy Tecnogas Tecnogas Superiore and Superiore are registered trademarks of TECNO TECNO, S.P. 63R n. 111, 42044 Gualtieri (RE), Italy T. +39 0522 222 161 tecnogassuperiore@tecnospa.
461308626 - rev 002 10/2017 superiore.us superiore.
