461308462 07-2015 INSTALLATION MANUAL FOR 30’’ AND 36’’ GAS RANGES
Table of Contents Warnings & Important Safety Instructions Dimensions Specifications Technical data Clearance Dimensions (Proximity to Cabinets) Clearance Dimensions (Wood/Composite Overlay) Electrical & Gas Requirements General Information Installation/ Door Removal Leg Installation/Adjustments/Alignments Anit-tip Device Installation Connecting Gas & Electrical Final Preparation Performance Checklist Service & Registration Warranty USA 3 6 10 11 12 13 15 16 17 18 19 20 20 22 23 WARNING: If the inform
Warnings & Important Safety Instructions • Before beginning, please read these instructions completely and carefully. • DO NOT remove permanently affixed labels, warnings, or plates from product. This may void the warranty. • All local and national codes and ordinances must be observed. Installation must conform with local codes or in the absence of codes, the National Fuel Gas Code ANSIZ223.1 INFPA54.
Warnings & Important Safety Instructions A GFI shall be used if required by NFPA-70 (National Electric Code), federal/state/local laws, or local ordinances. •The required use of a GFI is normally related to the location of a receptacle with respect to any significant sources of water or moisture. •TECNOGAS SUPERIORE will NOT warranty any problems resulting from GFI outlets which are not installed properly or do not meet the requirements below.
Warnings & Important Safety Instructions CHEMICAL HAZARD To avoid risk of property damage and/or personal injuryor death; this appliance is not too be used as a heating source. • Benzene is a chemical which is part of the gas supply to this cooking product, which is consumed in the flames during combustion. Exposure to a small amount of benzene is possible if a gasleak occurs. Formaldehyde and soot are by products of incomplete combustion.
Dimensions 35" 7/8 min - 37" 5/16 max 2" 1" 3/8 30” Gas Ranges 23 29 " 8 "7 / 2" 3 / 16 Note: Unit shown with island trim. Note: All gas ranges are equipped with spacer on the back (25/64) to prevent over heating of the wall.
2" 3/16 23" 26" 7/8 2" 3/8 1" 11/32 1" 11/32 1" 3/8 2" 1/8 2" 5" Electricity 2" 27/64 461308462 07-2015 2" 6/8 3/8" 25" 33" 2" 1" 3/8 29" 7/8 2" 6/8 min 4" 1/4 max 35" 15/32 min - 36" 7/8 max 2" 1/8 5" 35" 7/8 min - 37" 5/16 max Dimensions 30” Gas Ranges 1" 3/8 29" 7/8 Gas 5" 9/16 2" 3/8" 1" 1/2 7
Dimensions 35" 7/8 min - 37" 5/16 max 2" 1" 3/8 33" 36”Gas Ranges 23 " 35 " 7 /8 2" 3 / 16 Note: Unit shown with island trim. Note: All gas ranges are equipped with spacer on the back (25/64) to prevent over heating of the wall.
2" 3/16 23" 26" 7/8 2" 3/8 1" 11/32 1" 11/32 1" 3/8 2" 1/8 2" 5" Electricity 2" 27/64 461308462 07-2015 2" 6/8 3/8" 2" 25" 33" 2" 1" 3/8 35" 7/8 2" 6/8 min 4" 1/4 max 35" 15/32 min - 36" 7/8 max 2" 1/8 5" 35" 7/8 min - 37" 5/16 max Dimensions 36”Gas Ranges 1" 3/8 35" 7/8 Gas 5" 9/16 2" 3/8" 1" 1/2 9
Specifications Technical data Burners - injectors and volume, range 30‘‘ (mod. ...301...) Natural 4’’ LP/Propane 11’’ By-pass Inj. W BTU/h Inj. W BTU/h Ø W BTU/h Small burner 92 1055 3600 56 1055 3600 28 322 1100 Medium burners 117 1300 6500 70 1300 6500 34 381 1300 Large burner 155 2750 11000 93 2750 11000 44 791 2700 Power burner Ext. ring Int. ring 137 (2) 80 4750 18000 82 (2) 50 4750 18000 65 1377 4700 Power burner with simmer Ext. ring Int.
Clearance Dimensions (Proximity to Cabinets) •This range may be installed directly adjacent to existing 36” (91.4 cm) high base cabinets. IMPORTANT: The side trim MUST be 3/8” (0.95 cm) above the adjacent base cabinet countertop. This can be accomplished by raising the unit adjusting the legs. • The range CANNOT be installed directly adjacent to sidewalls, tall cabinets, tall appliances, or other side vertical surfaces above 36”(91.4 cm) high.
Clearance Dimensions (Wood/Composite Overlay) The bottom of a standard hood should be 30” (76.2 cm) min. to 36” (91.4 cm) max. above the countertop. This would typically result in the bottom of the hood being 66” (167.6 cm) to 72” (182.9 cm) above the floor. Refer to the range hood installation instructions for additional information. These dimensions provide for safe and efficient operation of the hood. Important: There must be a minimum of 6” (15.
Electrical & Gas Requirements Electrical Requirements Check your national and local codes regarding this unit. This range requires120VAC/60 Hz; 4 ft. (121.9 cm), 3-wire cord with grounded 3-prong plug attached to unit. See “Electrical Connection” section for grounding instructions. Must be fused seperately from any other circuit.
Gas Requirements TO INSTALL PRESSURE REGULATOR 1: Remove the 2 covers on the back of the 3 - Screw the assembled pressure regurange unscrewing the 3 screws indicated lator on the range like shown on picture below. Pay attention to the vertical aligneon below pictures. ment of the same pressure regulator. COVERS SCREWS 2 - Take from the top of packaging the parts shown in the picture below to assemble the pressure regulator. 14 4 - Re-install the covers previously removed.
Gas Requirements Flexible Connections: If the unit is to be installed with flexible couplings and/or quick-disconnect fittings, the installer must use a heavy-duty AGA design-certified flexible connector or at least1/2” (1.3 cm) ID NPT (with suitable strainreliefs) in compliance with ANSI Z21.41and Z21.69. In Canada: CAN 1-6, 10-88 metal connectors for gas appliances and CAN 1-6.9 M79 quick disconnect devices for use with gas fuel.
Gas Requirements GAS CONVERSION WARNING! Before carrying out this operation, disconnect the appliance from gas and electricity. Gas conversion shall be conducted by a factory-trained professional. Call the customer service hotline to identify a factory-trained professional near your home. The gas conversion procedure for this range includes 6 steps: 1. Pressure regulator 2. Surface burners 3. Main oven burner 4. Broiler burner 5.Visual checks prior to closure of oven bottom panel 6.
Gas Requirements STEP 3: MAIN OVEN BURNER To replace the nozzles of the main oven burner, start by removing the bottom panel of the oven. Loose the 2 screw located on the left and right sides of the burner and the burner from its support. ATTENTION: pay extra attention to avoid damage to the igniter and thermocouple. Unscrew the nozzle located inside the gas fitting using a 10 mm or 7 mm socket wrench.
Gas Requirements Replace the nozzle using the conversion set supplied with the range or by a Tecno authorized parts warehouse. Each nozzle has a number indicating its flow diameter printed on the body. Consult the table on “Specifications Technical data “ paragraph for matching nozzles to burners. Air adjustment is not needed. STEP 4: BROILER BURNER Loosen the 2 screws on left and right sides and pull out the burner from its support burner from its support.
Gas Requirements STEP 5:VISUAL CHECKS Before reinstalling the bottom panel, the following visual check must be performed to ensure that the conversion has been carried out properly and without damage to other components of the range. OVEN IGNITER AND THERMOCOUPLE POSITION The appropriate gap between the tip of the spark plug or thermocouple and the burner shall be approximately 1/8’’.
Gas Requirements OVEN BURNER 1. Set the oven temperature control knob to the MAXIMUM setting. 2. Close the oven door and operate the oven for at least 10 minutes. 3. Set the knob to the MINIMUM setting 4. Remove the knob. 5.
General Information • All openings in the wall behind the appliance and in the floor under the appliance must be sealed. • Do not obstruct the flow of combustion and ventilation air. CAUTION Avoid any damage to oven vents. The vents need to be un obstructed and open to provide proper airflow for optimal oven performance. CAUTION The cooling fans should be operating when the unit is in operation.
Installation/Door removal NOTICE DO NOT use the handle or oven door to lift the oven. DO NOT lift or carry the door by the handle. Removing the door must be done by your dealer, a qualified licensed plumber, or certified gas installer Door Removal 1)- Open the door completely. Place the pins, supplied with unit, in pin hole. For personal safety, ONLY use pins supplied with the unit. 2)- Grasp the door as indicated in the photos below and turn up until you perceive the block.
Leg Installation/Adjustments/Alignment Tecnogas ranges must be used only with the legs properly installed. Adjust leg height to the desired level by twisting the inside portion of the leg assembly until the proper height is reached. Check with a level that the worktop allignement is perfectly level.
Anti-tip Device Installation WARNING TIPPING HAZARD: To reduce the risk of property damage or personal injury; install anti-tipping device provided in accordance with the installation instructions in this document. Device must be engaged properly to prevent product from tipping over. TIPPING Kit enclosed with the range. Mark and drill holes where the bracket will be located.
Connecting Gas & Electric DANGER GAS LEAK HAZARD To avoid risk of personal injury or death; leak testing of the appliance must be conducted according to the manufacturer’s instructions. Before placing appliance in operation, always check for gas leaks with soapy water solution. • DO NOT USE AN OPEN FLAME TO CHECK FOR GAS LEAKS. Before placing appliance in operation, always check for gas leaks.
Final Preparation •All stainless steel body parts should be wiped with hot, soapy water and with a liquid cleaner designed for this material. If buildup occurs, DO NOT use steel wool, abrasive cloths, cleansers, or powders! If it is necessary to scrape stainless steel to remove encrusted materials, soak with hot, wet cloths to loosen the material, then use a wool or nylon scraper.
Performance Checklist Worktop burner knob + simmer OFF = Closed position = “Full on” position internal ring = “Full on” position esternal ring Gas oven switch knob range 30’’ OFF = Closed position from MIN to MAX = Oven temperatures (300-450 °F) Broil = Broil Gas oven switch knob range 36’’ OFF from MIN to MAX (300-500 °F) Broil = Closed position = Oven temperatures = Broil Electric griddle knob range 36’’ from 1 to 7 positions = Closed position = Griddle temperatures 461308462 07-
Service & Registration Only authorized replacement parts may be used in performing service on the appliance. All servicing should be referred to a qualified technician. Contact TECNOGAS SUPERIORE 1-844-322-2111, for the nearest service parts distributor in your area or write to: CUSTOMERCARE@TECNOSPA.IT Record the information indicated below. You will need it if service is ever required. The model and serial number can be found by looking in the last page of this booklet.
WARRANTY U.S.A Please record your model (MOD) and serial number (S/N) below for future reference. For your convenience, a label containing this information is supplied with this booklet.
WARRANTY U.S.A 6) Any repair, modification, alteration, or adjustment provided by any person not authorized by TECNOGAS SUPERIORE. 7) Failure of the product if it is abused, misused or used for other than the intended purpose or if used commercially/industrially. 8) Incorrect electric current, voltage or power supply. 9) Improper setting of any control. 10) Replacement of house fuses or resetting of circuit breakers. 11) Replacement of the light bulbs.
461308462 07-2015 Electric diagram 30” 31
Electric diagram 36” 6 burners 32
461308462 07-2015 Electric diagram 36”4 burners + griddle 33
CONVERSION LABEL INSTALLATION LABEL Labels
461308462 07-2015
tecnogassuperiore.
