SUPER ® The SC813/SC813M Chassis Series Installation Guide Rev. 1.
SC813/813M Chassis User's Guide Table of Contents Chapter I: Introduction ............................................................... 1-3 A. Packing Lists ............................................................................................... 1-3 B. Front Panel LED Indicators ....................................................................... 1-4 C. SC813/SC813M Chassis Specifications ................................................. 1-5 D. SC813/SC813MPower Supply Specifications ..........
Chapter 1: Introduction Chapter 1- Introduction A. Packing Lists A-1 The SC813 chassis The SC813 chassis contains the following: One (1) Slim CD ROM Drive [CDM-TEAC-24(B)] Four (4) SCA 1" drive trays [CSE-PT39-(B)] One (1) Slim 3.
SC813/813M Chassis User's Guide A-2 The SC813M chassis: The SC813M chassis contains the following: Four (4) SCA 1" drive trays [CSE-PT39(B)] One (1) 350W Power Supply [PWS-042-24] (for the 350W Series) One (1) 300 W Power Supply [PWS-0054] (for the 300W Series) One (1) 420 W Power Supply [PWS-0053] (for the 420W Series) Three (3) 40mm Fans [FAN-0061] (in the 300W & 350W Series) Four (4) 40mm Fans [FAN-0061] (in the 420W & 500W Series) One (1) 4-port SATA backplane [CSE-SATA-813] (*for the 813MT Series)] One
Chapter 1: Introduction C. Specifications of the SC813/SC813M Chassis C-1. Specifications of Model Form Factor CPU Support Max.
SC813/813M Chassis User's Guide D. Power Supply Specifications of the SC813/SC813M Chassis D-1. Power Supply Specifications of the SC813 Chassis Power Supply Spec SC813 Mfr. Model # Mfr. Part # Rated AC Input Voltage Rated Input Frequency Rated Input Current SP502-IS PWS-048 100-240V AC 50-60 Hz 10A (115V) 5A (230V) 500W 2750 BTUs/Hr Rated Output Power Maximum rated BTU Nominal Output Vlotage +3.3V +5 +12 -5 -12 +5Vsb 20A 20A 36A N/A 1A 2A D-2. Power Supply Specifications of Serial # Mfr.
Chapter 2: Installation Procedures Chapter 2: Installation Procedures Section 1: Installing Components into the SC813 Chassis A. Removing the top cover from the chassis Before installing any components, replacing chassis fans or accessing the motherboard, you will first need to remove the top cove from the chassis. Procedures 1. Press the release tabs to release the top cover from its locking position. 2.
SC813 Chassis User's Guide B. Accessing the SCA Drive Tray and Installing a Hard Drive To install the SCA drive into the chassis, you need to first remove the SCA drive tray from the chassis so that the SCA drive can be installed in. Procedures 1. Press the release tab to release the SCA drive tray from its locking position. 2. Pull the SCA drive tray out from the chassis as shown below: Pull out the SCA drive tray from the chassis Press the release Tab 3.
Chapter 2: Installation Procedures C. Rail Installation Rail Packaging includes: *One pair of inner slides to be installed on the chassis, *One pair of outer slides to be installed in the rack, *Two pairs of short brackets to be used on the front side of the outer slides (Note: One pair of short brackets include screw threads, and the other pair do not. Use the only pair that will fit into your rack.
SC813 Chassis User's Guide C-3 Installing the Slide Assemblies to the Rack Procedures 1. After you have installed the short and long brackets to the outer slides, you are ready to install the whole slide assemblies (-outer slides with short and long brackets attached) to the rack. (See the previous page.) 2.
Chapter 2: Installation Procedures D. Installing the Chassis into the Rack Procedures 1. Push the inner slides, which are attached to the chassis, into the grooves of the outer slide assemblies that are installed in the rack as shown below: Inner slides Grooves of the outer slide assemblies 2. Push the chassis all the way to the back of the outer slide assemblies as shown below: (The plastic bezel is not included in the package.
SC813 Chassis User's Guide Section 2: SCSI (Super) GEM Driver Installation Instructions for Windows OS Please refer to the following instructions to install GEM Driver for the Windows OS systems. the SCSI (*Note: This driver is not necessary for other Operating Systems. If you have two SCA backplanes, you will need to install the driver twice.) The driver is located on the Super Micro motherboard driver CD or is available for download from our FTP site: ftp://ftp.supermicro.
Adding a Floppy Drive SC813M Chassis Adding a Floppy Drive 1-1 Overview The SC813M series of chassis includes the SC813MS-420C, the SC813MT-420C, the SC813MS-300C and the SC813MT-300C. These chassis come equipped with a front side USB/COM port tray as part of the standard configuration. Supermicro has designed the SC813M series so that the USB/COM port tray can be replaced with a slim floppy drive.
SC813M Addendum Figure 1-1.
Adding a Floppy Drive 1-2 Installation Procedure Following the steps in the order given will eliminate the most common problems associated with this install. Before beginning, you should power down the system and remove the power cord. Removing the Front Panel USB/COM Port Tray 1. With the power removed from the system, first remove the top chassis cover (refer to the system manual for help). 2. A COM2 and one or two USB cables run from the tray to the motherboard.
SC813M Addendum Installing the Assembled Floppy into the Chassis You are now ready to install the assembled floppy drive into the chassis 1. Insert the assembled floppy drive into the open space where the front panel tray used to be. Push it in until it locks into place. 2. Attach the white header on the floppy power cable to the drive and the black header to the floppy adapter (see Figure 1-2). 3.
