SUPER SUPER P4SCT SUPER P4SCT+ SUPER P4SCT+II USER’S MANUAL Revision 1.
The information in this User’s Manual has been carefully reviewed and is believed to be accurate. The vendor assumes no responsibility for any inaccuracies that may be contained in this document, makes no commitment to update or to keep current the information in this manual, or to notify any person or organization of the updates. Please Note: For the most up-to-date version of this manual, please see our web site at www.supermicro.com.
Preface Preface About This Manual This manual is written for system integrators, PC technicians and knowledgeable PC users. It provides information for the installation and use of the SUPER P4SCT/P4SCT+/P4SCT+II motherboard. The P4SCT/P4SCT+/ P4SCT+II supports single Intel Pentium® 4 processors or Celeron processors up to 3.40 GHz (with Hyper Threading) at a system bus speed of 800/ 533/400 MHz.(*see the note below).
SUPER P4SCT/P4SCT+/P4SCT+II User’s Manual Table of Contents Preface About This Manual ...................................................................................................... iii Manual Organization ................................................................................................... iii Chapter 1: Introduction 1-1 Overview ......................................................................................................... 1-1 Checklist ...................................
Table of Contents Serial Ports ............................................................................................. 2-12 Fan Headers ........................................................................................... 2-12 Chassis Intrusion ................................................................................... 2-13 Wake-On-LAN ......................................................................................... 2-13 Ethernet Ports: GLAN1 and GLAN1 ...........................
Table of Contents Chapter 4: BIOS 4-1 Introduction ....................................................................................................... 4-1 4-2 Running Setup .................................................................................................. 4-2 4-3 Main BIOS Setup .............................................................................................. 4-2 4-4 Advanced BIOS Setup .................................................................................
Chapter 1: Introduction Chapter 1 Introduction 1-1 Overview Checklist Congratulations on purchasing your computer motherboard from an acknowledged leader in the industry. Supermicro boards are designed with the utmost attention to detail to provide you with the highest standards in quality and performance. Please check that the following items have all been included with your motherboard. If anything listed here is damaged or missing, contact your retailer.
SUPER P4SCT/P4SCT+/P4SCT+II User’s Manual Contacting Supermicro Headquarters Address: Tel: Fax: Email: Web Site: SuperMicro Computer, Inc. 980 Rock Ave. San Jose, CA 95131 U.S.A. +1 (408) 503-8000 +1 (408) 503-8008 marketing@supermicro.com (General Information) support@supermicro.com (Technical Support) www.supermicro.com Europe Address: Tel: Fax: Email: SuperMicro Computer B.V. Het Sterrenbeeld 28, 5215 ML 's-Hertogenbosch, The Netherlands +31 (0) 73-6400390 +31 (0) 73-6416525 sales@supermicro.
Chapter 1: Introduction SUPER P4SCT Figure 1-1. SUPER P4SCT Image (1. *Please see Notes on the next page for the differences between the P4SCT, the P4SCT+ and the P4SCT+II. 2. *All graphics and pictures shown in this manual were based upon the latest PCB revision available at the time of publishing of this manual. The motherboard you've received may or may not look exactly the same as the graphics shown in this manual.
SUPER P4SCT/P4SCT+/P4SCT+II User’s Manual J17 PWR LED J20 24-pin ATX PWRConn COM2 JPUSB J10 WOR JP20 PWR Froce On J13 82547 Watch Dog CPU Parallel Port COM 1 JP1 JP2 CPU Speed LAN CTLR J9 VGA J21 +12V PWR JP8 Super I/O USB 1/2 JPWAKE KB/Mouse J11 SUPER P4SCT/P4SCT+/P4SCT+II Motherboard Layout CPU/CHFan1 Figure 1-4.
Chapter 1: Introduction P4SCT/P4SCT+/P4SCT+II Quick Reference Jumpers Description Default Setting J18 J33 J36 JBT1 JP1,JP2 JP8 JP20 JPL2 (P4SCT+/SCT+II) JPS1 (P4SCT+/SCT+II) JPUSB JPWAKE Speaker VGA Enable/Disable Keylock Header CMOS Clear CPU Clock Speed Watch Dog Reset Power Force On GLAN2 Marvell's SATA Enable USB1/2 Wake Up KB Wake Up Pins 3-4 (In.
SUPER P4SCT/P4SCT+/P4SCT+II User’s Manual DATA ADDR 4x/8xAGP (P4SCT/SCT+II) CTLR Processor 0 4DIMMs DDR266,DDR333,DDR400 AGP BUS DIMM E875P & E7210 MCH 1x GbE IntelR CSA (66MHz) USB 2.0 (4)Ports SATA (2) Ports DIMM Marvellx4 (P4SCT+/SCT+II) Hub A USB SATA UDMA 100 IntelR Hance Rapids LPC BUS ATA/100 (2) Ports DDR BUS 64-bit PCI BUS PCI-X (X3) GLAN (P4SCT+/ P4SCT+II) 32-bit PCI BUS PCI (X2) FWH LPC I/O KB/Mouse FDD Serial Port Printer H/W Monitor Figure 1-6.
Chapter 1: Introduction Motherboard Features CPU Latest CPU technology! • Single Pentium® 4 478-pin PGA processors or Intel Celeron processors up to up to 3.40 GHz (at a 800/533/400 MHz FSB) w/HyperThreading. • Intel Pentium 4/Celeron processors (*use 0.09 or 0.13 Micron Manufacturing Technology CPUs) Note: Refer to the motherboard specifications pages on our web site (http:// www.supermicro.com/Product_page/product-m.htm) for updates on supported processors.
SUPER P4SCT/P4SCT+/P4SCT+II User’s Manual ACPI Features • Microsoft OnNow • Slow blinking LED for suspend state indicator • BIOS support for USB keyboard • Main switch override mechanism • Internal/external modem ring-on Onboard I/O • 2 ATA100/66 EIDE Channels for a total of 4 IDE devices backward compatible • Intel 6300ESB (Hance Rapids) SATA Controller with support of 2 Onchip SATA ports • Marvell 88SX5040 SATA Controller with support of 4 SATA ports (*P4SCT+/P4SCT+II only) • 1 floppy port
Chapter 1: Introduction 1-2 Chipset Overview: Intel's Canterwood(875P) and Canterwood ES (E7210) Intel’s Canterwood Chipset (875P) and Canterwood ES (E7210) contains the following main components: Canterwood Memory Controller Hub (MCH) and the I/O Controller Hub (6300ESB-Hance Rapids ICH). These two components are interconnected via Hub Interface. Memory Controller Hub (MCH) The Canterwood Memory Controller Hub (MCH) is designed to support Intel PGA 478-pin Processors.
SUPER P4SCT/P4SCT+/P4SCT+II User’s Manual Marvell's 88SX5041 Host Controller (*For the P4SCT+/P4SCT+II only) The Marvell 88SX5080 device is a PCI/PCI-X to Serial ATA (SATA) host controller with expansion ROM interface. Based upon the SATA interface specification, the 88SX5080 device provides solutions for designs based on chipsets that do not integrate a SATA host controller. With the expansion ROM interface, the 88SX5080device enables the 88SX5080 add-in cards to boot from the host controller.
Chapter 1: Introduction 1-3 PC Health Monitoring This section describes the PC health monitoring features of the SUPER P4SCT/P4SCT+/P4SCT+II. The motherboard has an onboard System Hardware Monitor chip that supports PC health monitoring. Eight Onboard Voltage Monitors for the CPU Core, +3.3V, +3.3V standby, + 5V, +5V standby, Vbat and ± 12V The onboard voltage monitor will scan these voltages continuously.
SUPER P4SCT/P4SCT+/P4SCT+II User’s Manual 1-4 Power Configuration Settings This section describes features of your motherboard that deal with power and power settings. Microsoft OnNow The OnNow design initiative is a comprehensive, system-wide approach to system and device power control. OnNow is a term for a PC that is always on but appears to be off and responds immediately to user or other requests.
Chapter 1: Introduction Wake-On-LAN (WOR) Header Wake-On-LAN is defined as the ability of a management application to remotely power up a computer that is powered off. Remote PC setup, updates and asset tracking can occur after hours and on weekends so that daily LAN traffic is kept to a minimum and users are not interrupted. The motherboards have a 3-pin header (WOL) to connect to the 3-pin header on a Network Interface Card (NIC) that has WOL capability.
SUPER P4SCT/P4SCT+/P4SCT+II User’s Manual 1-6 Super I/O The disk drive adapter functions of the Super I/O chip include a floppy disk drive controller that is compatible with industry standard 82077/765, a data separator, write pre-compensation circuitry, decode logic, data rate selection, a clock generator, drive interface control logic and interrupt and DMA logic.
Chapter 2: Installation Chapter 2 Installation 2-1 Static-Sensitive Devices Electric Static Discharge (ESD) can damage electronic components. To prevent damage to your system board, it is important to handle it very carefully. The following measures are generally sufficient to protect your equipment from ESD. Precautions • Use a grounded wrist strap designed to prevent static discharge. • Touch a grounded metal object before removing the board from the antistatic bag.
SUPER P4SCT/P4SCT+/P4SCT+II User's Manual 2-2 Processor and Heatsink Fan Installation ! When handling the processor package, avoid placing direct pressure on the label area of the fan. IMPORTANT: Always connect the power cord last and always remove it before adding, removing or changing any hardware components. Make sure that you install the processor into the CPU socket before you install the CPU heatsink. Installation of the Processor and Heatsink 1.
Chapter 2: Installation 5. Lift the lever on the CPU socket. Socket Lever 6. Install the CPU in the socket. Make sure that Pin 1 of the CPU is seated on Pin 1 of the socket (both corners are marked with a triangle). 7. Press the lever down until you hear it *click* into the locked position. Socket lever in locked position 8. Apply the proper amount of thermal compound to the CPU die. 9.
SUPER P4SCT/P4SCT+/P4SCT+II User's Manual Figure 2-1. 478-pin mPGA Socket: Empty and with Processor Installed Lever Pin 1 Pin 1 Processor 2-3 (installed) Mounting the Motherboard in the Chassis All motherboards have standard mounting holes to fit different types of chassis. Make sure the location of all the mounting holes for both the motherboard and the chassis match.
Chapter 2: Installation Support The P4SCT/P4SCT+/P4SCT+II supports Dual channel, ECC/non-ECC, unbuffered DDR-400/333/266 SDRAM. (Populate DIMM0A,DIMM1A and/ or DIMM0B, DIMM1B with memory modules of the same size/same type will result in the dual channel, two-way interleaved memory which is faster than the single channel memory. (*Note: The Canterwood chip supports non-ECC or ECC memory. If ECC memory is installed, the ECC bits need to be initialized via BIOS before normal operation. For a 4 GB-Memory and 2.
SUPER P4SCT/P4SCT+/P4SCT+II User's Manual 2-5 I/O Port/Control Panel Connector Locations The I/O ports are color coded in conformance with the PC99 specification to make setting up your system easier. See Figure 2-3 below for the colors and locations of the various IO ports. Figure 2-3.
Chapter 2: Installation 2-6 Connecting Cables ATX Power Supply 24-pin Connector Pin Definitions (J20) Pin Number Definition Pin Number Definition 1 +3.3V 13 +3.3V 2 +3.3V 14 -12V 3 COM 15 COM 4 +5V 16 PS_ON# 5 COM 17 COM 6 +5V 18 COM 7 COM 19 COM 8 PWR_OK 20 Res(NC) 9 5VSB 21 +5V 10 +12V 22 +5V 11 +12V 23 +5V 12 +3.3V 24 COM Power Supply Connectors The primary power supply connector (J20) on the P4SCT/ P4SCT+/P4SCT+II meets the SSI (Superset ATX) 24-pin specification.
SUPER P4SCT/P4SCT+/P4SCT+II User's Manual Reset Connector Reset Pin Definitions (JF1) The reset connector is located on pins 3 and 4 of JF1. This connector attaches to the reset switch on the computer chassis. See the table on the right for pin definitions. Pin Number Definition 3 Reset Ground 4 Overheat (OH) LED Pin Definitions (JF1) Overheat LED (OH) Connect an LED to the OH connection on pins 7 and 8 of JF1 to provide advanced warning of chassis overheating.
Chapter 2: Installation GLAN1 LED GLAN1 LED Pin Definitions (JF1) The GLAN1 (Gigabit LAN) LED connection is located on pins 11 and 12 of JF1. Attach the LAN1 LED cable to display Gigabit LAN 1 activity. Refer to the table on the right for pin definitions. Pin Number Definition Vcc 11 GND 12 GLAN2 LED(*P4SCT+/ P4SCT+II Only) GLAN2 LED (*P4SCT+) Pin Definitions (JF1) The GLAN2 LED connection is located on pins 9 and 10 of JF1. Attach the GLAN2 LED cable to display Gigabit LAN 2 activity.
SUPER P4SCT/P4SCT+/P4SCT+II User's Manual *IDE LED (*See the note below) IDE Pin Definition The IDE LED is located on pins 13, 14 of JF1. This connects to the hard drive LED to display all IDE and SATA activities. See the table on the right for pin definitions.
Chapter 2: Installation NMI Button The non-maskable interrupt button header is located on pins 19 and 20 of JF1. Refer to the table on the right for pin definitions. Speaker Connector NMI Button Pin Definitions (JF1) Pin Number Definition 19 Ground 20 Control Sp e a k er: P in D e fin itio n The speaker connector is located on J18. See the table on the right for pin definitions.
SUPER P4SCT/P4SCT+/P4SCT+II User's Manual Serial Ports Two serial ports are included on the motherboard: COM1(J9) is a port located beside the mouse/ keyboard ports and COM2(J10) is a header located on the motherboard near J20 (Power Connector). See the table on the right for pin definitions. Serial Port Pin Definitio ns (COM 1, CO M2) Pin Number 1 2 3 4 5 Definition CD RD TD DT R Ground Pin Number 6 7 8 9 10 Definition DSR RTS CTS RI NC Note: Pin 10 is included on the header but not on the port.
Chapter 2: Installation Chassis Intrusion The Chassis Intrusion header is designated JL1. See the board layout in Chapter 1 for the location of JL1 and the table on the right for pin definitions. Chassis Intrusion Pin Definitions (JL1) Pin Number Definition 1 Intrusion Input 2 G round Wake-On-LAN WOR Parallel Port COM 1 VGA Pin Number 1 2 3 PWR LED 24-pin ATX PWR Conn +12V 4-pin PWR Conn.
SUPER P4SCT/P4SCT+/P4SCT+II User's Manual Ethernet Ports GLAN1 and GLAN2 (*P4SCT/P4SCT+II only) Two Ethernet ports (designated GLAN1 and GLAN2) are located beside the VGA port on the IO backplane. These ports accept RJ45 type cables. VGA Connector A VGA connector (JG1) is located next to the GLAN1 on the IO backplane. Refer to the board layout below for the location. SMB Header Pin Definitions (J15) SMB Header Pin Number 1 2 3 4 WOR Parallel Port VGA A +12V 4-pin PWR Conn.
Chapter 2: Installation ATX PS/2 Keyboard and PS/2 Mouse Ports PS/2 Keyboard and Mouse Port Pin Definitions (J11) The ATX PS/2 keyboard and the PS/2 mouse are located on J11. See the table on the right for pin definitions. (The mouse port is above the keyboard port. See the table on the right for pin definitions.
SUPER P4SCT/P4SCT+/P4SCT+II User's Manual Wake-On-Ring The Wake-On-Ring header is designated WOR. This function allows your computer to receive and be "awakened" by an incoming call when in the suspend state. See the table on the right for pin definitions. You must also have a WOR card and cable to use WOR. Keylock Enable/Disable Parallel Port VGA +12V 4-pin PWR Conn.
Chapter 2: Installation Intel's SATA LED Pin Definitions (J37) Intel's SATA LED The header for Intel's SATA LED is located on J37. This header will display all Intel's SATA activities. See the table on the right for pin definitions. Pin Number Definition 1 (I-)SATA1 2 (I-)SATA2 3 NC 4 NC 5 NC Marvell's SATA LED (*P4SCT+/ P4SCT+II Only) Marvell's SATA Pin Definitions (JS9) Pin Number 1 2 3 4 5 The header for Marvell's SATA LED is located on JS9. This header will display all Marvell's SATA activities.
SUPER P4SCT/P4SCT+/P4SCT+II User's Manual 2-7 Jumper Settings Explanation of Jumpers To modify the operation of the motherboard, jumpers can be used to choose between optional settings. Jumpers create shorts between two pins to change the function of the connector. Pin 1 is identified with a square solder pad on the printed circuit board. See the motherboard layout pages for jumper locations.
Chapter 2: Installation Marvell's SATA Enable (*P4SCT+/P4SCT+II Only) Marvell's SATA Enable Jumper Settings (JPS1) (P4SCT+/P4SCT+II Only) Jumper JPS1 is used to enable or disable Marvell's Serial ATA Controller. See the table on right for pin definitions. Intel's Serial ATA Controller is enabled or disabled via the BIOS.
SUPER P4SCT/P4SCT+/P4SCT+II User's Manual Watch Dog Enable/Disable Watch Dog Jumper Settings (JP8) WOR Parallel Port VGA PWR LED 24-pin ATX PWR Conn +12V 4-pin PWR Conn. PWR Force On Watch Dog PWR Froce On A CPU Speed 82547 LAN CTLR COM 1 Jumper Position Pins 1-2 Pins 2-3 Open CPU 478 PGA A.
Chapter 2: Installation Keyboard Wake-Up Keyboard Wake-Up Jumper Settings (JPWAKE) Jumper The JPWAKE jumper is used to allow the system to be woken up by depressing a key on the keyboard from S1 or S3 in Windows OS. See the table on the right for jumper settings. Your power supply must meet ATX specification 2.01 or higher and supply 720 mA of standby power to use this feature.
SUPER P4SCT/P4SCT+/P4SCT+II User's Manual VGA Enable/Disable VGA Enable/Disable Jumper Settings (J33) J33 allows you to enable or disable the VGA port. The default position is on pins 1 and 2 to enable VGA. See the table on the right for jumper settings. Jumper Position 1-2 2-3 Definition Enabled Disabled Front Side Bus Speed WOR B Parallel Port VGA PWR LED 24-pin ATX PWR Conn +12V 4-pin PWR Conn.
Chapter 2: Installation 2-8 Parallel Port, Floppy Drive, Hard Drive and AGP Connections Use the following information to connect the floppy and hard disk drive cables. • The floppy disk drive cable has seven twisted wires. • A red mark on a wire typically designates the location of pin 1. • A single floppy disk drive ribbon cable has 34 wires and two connectors to provide for two floppy disk drives.
SUPER P4SCT/P4SCT+/P4SCT+II User's Manual Floppy Connector Pin Definitions (J7) Pin Number Function Pin Number Function 1 GND 2 FDHDIN 3 GND 4 Reserved 5 Key 6 FDEDIN 7 GND 8 Index9 GND 10 Motor Enable 11 GND 12 Drive Select B13 GND 14 Drive Select A15 GND 16 Motor Enable 17 GND 18 DIR19 GND 20 STEP21 GND 22 Write Data23 GND 24 Write Gate25 GND 26 Track 0027 GND 28 Write Protect29 GND 30 Read Data31 GND 32 Side 1 Select33 GND 34 Diskette Floppy Connector The floppy connector is located on J7.
Chapter 2: Installation 1.5V 8xAGP Pro Slot (*P4SCT/P4ST+II) The P4SCT/P4SCT+/P4SCT+II includes an 8xAGP Pro slot for highperformance video cards. It is backward compatible with 4xAGP and 2xAGP graphics cards. To install a VGA card, power down the system and remove the I/O shield corresponding to the AGP Pro slot. Push the AGP card down and make sure that the golden finger does not show. Then, screw the AGP card onto the board. Replace all chassis covers before restoring power to the system.
SUPER P4SCT/P4SCT+/P4SCT+II User's Manual Notes 2-26
Chapter 3: Troubleshooting Chapter 3 Troubleshooting 3-1 Troubleshooting Procedures Use the following procedures to troubleshoot your system. If you have followed all of the procedures below and still need assistance, refer to the ‘Technical Support Procedures’ and/or refer to the section regarding ‘Returning Merchandise for Service in this chapter. Always disconnect the AC power cord before adding, changing or installing any hardware components. Before Power On 1.
SUPER P4SCT/P4SCT+/P4SCT+II User's Manual NOTE: If you are a system integrator, VAR or OEM, a POST diagnostics card is recommended. For I/O port 80h codes, refer to Appendix B. Memory Errors 1. Make sure the DIMM modules are properly and fully installed. 2. You should be using unbuffered ECC/Non ECC DDR memory (see next page). Also, it is recommended that you use the same memory speed for all DIMMs in the system. See Section 2-4 for memory limitations. 3.
Chapter 3: Troubleshooting 2. BIOS upgrades can be downloaded from our web site at http://www.supermicro.com/techsupport/download.htm. Note: Not all BIOS can be flashed, it depends on the modifications to the boot block code. 3.
SUPER P4SCT/P4SCT+/P4SCT+II User's Manual Question: What's on the CD that came with my motherboard? Answer: The supplied compact disc has quite a few drivers and programs that will greatly enhance your system. We recommend that you review the CD and install the applications you need. Applications on the CD include chipset drivers for Windows and security and audio drivers. Question: I see some of my PCI devices sharing IRQs, but the system seems to be fine.
Chapter 3: Troubleshooting Question: How do I connect the ATA100/66 cable to my IDE device(s)? Answer: The 80-wire/40-pin high-density ATA100/66 IDE cable that came with your system has two connectors to support two drives. This special cable must be used to take advantage of the speed the ATA100/66 technology offers. Connect the blue connector to the onboard IDE header and the other connector(s) to your hard drive(s).
SUPER P4SCT/P4SCT+/P4SCT+II User's Manual Notes 3-6
Chapter 4: BIOS Chapter 4 BIOS 4-1 Introduction This chapter describes the AwardBIOS for the P4SCT/P4SCT+/P4SCT+II. The Award ROM BIOS is stored in a Flash chip and can be easily upgraded using a floppy disk-based program. Note: Due to periodic changes to the BIOS, some settings may have been added or deleted and might not yet be recorded in this manual. Refer to the Manual Download area of our web site for any changes to BIOS that are not reflected in this manual.
SUPER P4SCT/P4SCT+/P4SCT+II User's Manual 4-2 Running Setup *Optimal default settings are in bold text unless otherwise noted. The BIOS setup options described in this section are selected by choosing the appropriate text from the Main BIOS Setup screen. All displayed text is described in this section, although the screen display is often all you need to understand how to set the options (see on next page). When you first power on the computer, the AwardBIOS™ is immediately activated.
Chapter 4: BIOS Date/Time Set the system date and time. Key in the correct information in the "mm", "dd" and "yy" fields. Press the "Enter" key to save the data. Legacy Diskette A This setting allows the user to set the type of floppy disk drive installed as diskette A. The options are "None", "360Kb, 5.25 in", "1.2MB, 5.25 in", "720Kb, 3.5 in", "1.44 MB, 3.5 in", and "2.88MB 3.5 in". Legacy Diskette B This setting allows the user to set the type of floppy disk drive installed as diskette B.
SUPER P4SCT/P4SCT+/P4SCT+II User's Manual 4-4 Advanced BIOS Setup Choose Advanced BIOS Setup from the Award BIOS main menu with the Left/Right arrow keys. You should see the following display. Select one of the items in the left frame of the screen to go to the sub screen for that item. Advanced BIOS Setup options are displayed by highlighting the option using the arrow keys. All Advanced BIOS Setup options are described in this section. 4-4.
Chapter 4: BIOS ACPI Function Select "Enabled" to activate the function of BIOS Support for Advanced Configuration and Power Interface features. The settings are "Enabled" or "Disabled". ACPI Suspend Type If enabled, the option allows the user to determine the ACPI Suspend type. The options are "S1(POS)", "S3(STR)", and S1&S3. APIC Mode This setting allows you to Enable or Disable APIC.
SUPER P4SCT/P4SCT+/P4SCT+II User's Manual ECC Configuration This setting allows you to enable or disable ECC (Error Correction and Checking). The options are "ECC" and "Non-ECC". CSA LAN (Giga-LAN) Select "Enabled" to activate the function of CSA LAN. The options are "Enabled" and "Disabled". Smart Fan Control Select "Enabled" to enable the function of Smart Fan Control. The options are "Disabled" and "Enabled". SATA Mode This setting allows you to set the SATA Mode RAID via BIOS.
Chapter 4: BIOS USB Legacy Support This setting allows you to enable or disable the functions of USB, Keyboard/ Mouse under POST and DOS. The options are Disabled, and Enabled. CPU THRM-Throttling THRM throttling is used to lower power consumption and reduce the heat generated by the CPU. The options for this setting are "87.5%", "75%", "62.5%", "50%", "37.5%", "25%' and "12.5%". 4-4.3 I/O Device Configuration Choose I/O Device Configuration from the Award BIOS main menu with the Left/Right arrow keys.
SUPER P4SCT/P4SCT+/P4SCT+II User's Manual UART Mode Select This setting allows the user to select the UART mode for the BIOS. The options are "IrDA", "ASKIR" and "Normal". RxD, TxD Active This allows the user to change the settings for the "RxD, TxD Active" function. The options are "Hi, Hi", "Hi, Lo", "Lo, Hi", and "Lo, Lo". IR Transmission Delay If "Enabled", the transmission of IR (infrared) signals will be delayed. The options are "Enabled" and "Disabled".
Chapter 4: BIOS Power On Function This setting allows the user to decide which method to use to power on the system. The options are "Password", "Hot Key", "Mouse Left", "Mouse Right", "Any Key", and "Button Only". KB Power On Password This setting allows the user to enter the Password when the system is powered on via keyboard. Hot Key Power On This setting allows the user to decide which hot-keys to use in order to power on the system.
SUPER P4SCT/P4SCT+/P4SCT+II User's Manual Resources Controlled By This setting allows BIOS to automatically configure all boot and Plug and Play compatible devices. If you choose Auto, you cannot select the IRQ, DMA and memory base address fields because BIOS automatically assigns them. The options are "Auto " and "Manual". Onboard CSA LAN Boot Select "Enabled" to enable the Boot ROM embedded in the Onboard CSA LAN Chip. The options are: "Enabled" and "Disabled". 4-4.
Chapter 4: BIOS Agent after Boot Select "Disabled" to allows the Agent of Console Redirection to continue running after OS bootup. The Options are "Enabled", and "Disabled". 4-4.6 Hardware Monitor Choose Hardware Monitor from the Award BIOS main menu with the Left/ Right arrow keys. You should see the following display: CPU Warning Temperature This allows you to set the CPU warning temperature.
SUPER P4SCT/P4SCT+/P4SCT+II User's Manual 4-4.7 Processor & Clock Options Limit CPUID MaxVal This feature allows the user to set the limit for the CPUID Maximum Value. The value can be set from 1 to 3. The options are "Enabled" and "Disabled". (*For Windows XP, the option should be set to "Disabled.
Chapter 4: BIOS 4-5 Security Choose Security from the Award BIOS main menu with the Left/Right arrow keys. You should see the following display: Set Supervisor Password When the item "Set Supervisor Password" is highlighted on the above screen, press the key. When prompted, type the Supervisor Password in the dialogue box to set or to change the Supervisor Password. Set User Password When the item "Set User Password" is highlighted on the above screen, press the key.
SUPER P4SCT/P4SCT+/P4SCT+II User's Manual 4-6 Boot Choose Boot from the Award BIOS main menu with the Left/Right arrow keys. You should see the following display: X Removable Device Priority This setting allows you to set the priority of removable devices. The options are "Floppy Disks", "LS120", "Zip 100", "USB-FDD0", "USB-FDD1", "USBZIP0", and "USB-ZIP1". X CD ROM Drives Boot Priority This item allows the user to specify the boot sequence of the available CD ROM Devices.
Chapter 4: BIOS Second Boot Device This item allows the user to set the second boot-up device. The options are "Removable", "Hard Disks", "CDROM", "Legacy LAN", and "Disabled". Third Boot Device This item allows the user to set the Third boot-up device. The options are "Removable", "Hard Disks", "CDROM", "Legacy LAN", and "Disabled".
SUPER P4SCT/P4SCT+/P4SCT+II User's Manual Load Fail-Safe Defaults Highlight this item and hit to load the default settings for all items in the BIOS Setup. These are the safest settings to use. Load Optimized Defaults Highlight this item and hit to load the optimized settings for all items in the BIOS Setup. These settings provide you with optimal system performance.
Appendix A: BIOS POST Messages Appendix A BIOS POST Messages During the Power-On Self-Test (POST), the BIOS will check for problems. If a problem is found, the BIOS will activate an alarm or display a message. The following is a list of such BIOS messages.
SUPER P4SCT/P4SCT+//P4SCT+II User's Manual Notes A-2
Appendix B: Award BIOS POST Codes Appendix B: Award BIOS POST Codes This section lists the POST (Power On Self Testing) Codes for the Award BIOS. POST (hex) CFh C0h C1h C3h C5h 0h1 02h 03h 04h 05h 06h 07h 08h 09h 0Ah 0Bh 0Ch 0Dh 0Eh Description Test CMOS R/W functionality. Early chipset initialization: -Disable shadow RAM -Disable L2 cache (socket 7 or below) -Program basic chipset registers Detect memory -Auto-detection of DRAM size, type and ECC.
SUPER P4SCT/P4SCT+//P4SCT+II User’s Manual POST (hex) 0Fh 10h 11h 12h 13h 14h 15h 16h 17h 18h 19h 1Ah 1Bh 1Ch 1Dh 1Eh 1Fh 20h 21h 22h 23h 24h 25h 26h 27h 28h 29h 2Ah 2Bh 2Ch Description Reserved Auto detect flash type to load appropriate flash R/W codes into the run time area in F000 for ESCD & DMI support. Reserved Use walking 1’s algorithm to check out interface in CMOS circuitry. Also set real-time clock power status, and then check for override.
Appendix B: Award BIOS POST Codes POST (hex) 2Dh 2Eh 2Fh 30h 31h 32h 33h 34h 35h 36h 37h 38h 39h 3Ah 3Bh 3Ch 3Dh 3Eh 3Fh 40h 41h 42h 43h 44h 45h 46h 47h 48h 49h 4Ah 4Bh 4Ch 4Dh 4Eh 4Fh 50h 51h 52h 53h 54h 55h 56h 57h Description 1. Initialize multi-language 2. Put information on screen display, including Award title, CPU type, CPU speed …. Reserved Reserved Reserved Reserved Reserved Reset keyboard except Winbond 977 series Super I/O chips.
SUPER P4SCT/P4SCT+//P4SCT+II User’s Manual POST (hex) 58h 59h 5Ah 5Bh 5Ch 5Dh 5Eh 5Fh 60h 61h 62h 63h 64h 65h 66h 67h 68h 69h 6Ah 6Bh 6Ch 6Dh 6Eh 6Fh 70h 71h 72h 73h 74h 75h 76h 77h 78h 79h 7Ah 7Bh 7Ch 7Dh 7Eh 7Fh Description Reserved Initialize the combined Trend Anti-Virus code. Reserved (Optional Feature) Show message for entering AWDFLASH.EXE from FDD (optional) Reserved 1. Initialize Init_Onboard_Super_IO switch. 2. Initialize Init_Onboard_AUDIO switch.
Appendix B: Award BIOS POST Codes POST (hex) 80h 81h 82h 83h 84h 85h 86h 87h 88h 89h 90h 91h 92h 93h 94h 95h 96h FFh Description Reserved Reserved 1. Call chipset power management hook. 2. Recover the text font used by EPA logo (not for full screen logo) 3. If password is set, ask for password. Save all data in stack back to CMOS Initialize ISA PnP boot devices 1. USB final Initialization 2. NET PC: Build SYSID structure 3. Switch screen back to text mode 4. Set up ACPI table at top of memory. 5.
SUPER P4SCT/P4SCT+//P4SCT+II User’s Manual NOTES B-6
Appendix C: Software Installation Instructions Appendix C Installing Software Drivers and Windows Operating System After all the hardware has been installed, you must first configure the Adaptec Embedded Serial ATA RAID Driver before you install the Windows operating system. The necessary drivers are all included on the Supermicro bootable CDs that came packaged with your motherboard. (*The following section provides information on Adaptec's SATA RAID Driver based on the Intel Hance Rapids ICH Controller.
SUPER P4SCT/P4SCT+/P4SCT+II User's Manual ATA Operate Mode You can select from the following two modes: Combined Mode and Enhanced Mode. Combined Mode: In this mode, system BIOS assigns the traditional IRQ 14 and IRQ 15 for the use of HDD. Up to 4 ATA devices are supported by this mode.
Appendix C: Software Installation Instructions Configuring BIOS settings for the SATA RAID Functions (Enhanced Mode) 1. Press the key during system bootup to enter the BIOS Setup Utility. (*Note: If it is the first time to power on the system, we recommend that you load the Optimized Default Settings. If you have already done so, please skip to Step 3. 2. Use the arrow keys to select the "Exit" Menu.
SUPER P4SCT/P4SCT+/P4SCT+II User's Manual The Adaptec Embedded Serial ATA with HostRAID Controller Driver Adaptec's Embedded Serial ATA RAID with HostRAID controller adds RAID functionality to the Serial ATA I/O controller by supporting RAID 0 (Striping) or RAID 1 (Mirroring) to enhance the industry's pioneer PCI-to-e host controller products. RAID striping (RAID 0) can greatly improve hard disk I/O performance because of its capability in striping data across multiple drives.
Appendix C: Software Installation Instructions Managing Arrays Select this option to view array properties, and delete arrays. The following sections describe the operations Of "Managing Arrays". To select this option, use the arrow keys and the key to select "Managing Arrays" from the main menu (as shown above).
SUPER P4SCT/P4SCT+/P4SCT+II User's Manual Viewing Array Properties To view the properties of an existing array: 1. At the BIOS prompt, press Ctrl+A. 2. From the ARC menu, select Array Configuration Utility (ACU). 3. From the ACU menu, select Manage Arrays (as shown on the previous screen.) 4. From the List of Arrays dialog box, select the array you want to view and press Enter. The Array Properties dialog box appears, showing detailed information on the array.
Appendix C: Software Installation Instructions Creating Arrays Before creating arrays, make sure the disks for the array are connected and installed in your system. Note that disks with no usable space, or disks that are un-initialized are shown in gray and cannot be used. See Initializing Disk Drives. To create an array: 1 Turn on your computer and press Ctrl+A when prompted to access the ARC utility.
SUPER P4SCT/P4SCT+/P4SCT+II User's Manual Assigning Array Properties Once you've create a new array, you are ready to assign the properties to the array. *Caution: Once the array is created and its properties are assigned, you cannot change the array properties using the ACU. You will need to use the Adaptec Storage Manager - Browser Edition. (Refer to Adaptec's User's Guide in the enclosed CD.) To assign properties to the new array: 1.
Appendix C: Software Installation Instructions 2. Under the item "Arrays Label", type in an label and press Enter. (*Note: The label shall not be more than 15 characters.) 3. For RAID 0, select the desired stripe size. (*Note: Available stripe sizes are 16, 32, and 64 KB-default. It is recommended that you do not change the default setting.) 4. The item: "Create RAID via" allows you to select between the different creating methods for RAID 0 and RAID 1.
SUPER P4SCT/P4SCT+/P4SCT+II User's Manual 5. When you are finished, press Done (as the screen shown below). Notes: 1. Before adding a new drive to an array, back up any data contained on the new drive. Otherwise, all data will be lost. 2. If you stop the Build or Clear process on a RAID 1 from ACU, you can restart it by pressing Ctrl+R. 3. A RAID 1 created using the Quick Init option may return some data miscompares if you later run a consistency check. This is normal and is not a cause for concern. 4.
Appendix C: Software Installation Instructions Adding a Bootable Array To make an array bootable: 1. From the Main menu, select Manage Arrays. 2. From the List of Arrays, select the array you want to make bootable, and press Ctrl+B. 3. Enter Y to create a bootable array when the following message is displayed: "This will make all other existing bootable array non-bootable. Do you want to make this array bootable? (Yes/No):" Then, a bootable array will be created.
SUPER P4SCT/P4SCT+/P4SCT+II User's Manual Adding/Deleting Hotspares (*Note: In order to rebuild a RAID (RAID 0 or RAID 1), you would need to add a new HDD as a hotspare.) 1. Turn on your computer and press Ctrl+A as prompted to access the ARC Utility. 2. From the ARC menu, select Array Configuration Utility (ACU). 3. From the ACU menu, select Add/Delete Hotspares. 4.
Appendix C: Software Installation Instructions Initializing Disk Drives If an installed disk does not appear in the disk selection list for creating a new array, or if it appears grayed out, you may have to initialize it before you can use it as part of an array. Drives attached to the controller must be initialized before they can be used in an array. Caution: Initializing a disk overwrites the partition table on the disk and makes any data on the disk inaccessible.
SUPER P4SCT/P4SCT+/P4SCT+II User's Manual 4. Use the up and down arrow keys to highlight the disk you wish to initialize and press Insert (as shown in the screen below).
Appendix C: Software Installation Instructions 5. Repeat Step 4 so that both drives to be initialized are selected (as shown in the screen below). 6. Press Enter. 7. Read the warning message as shown in the screen. 8. Make sure that you have selected the correct disk drives to initialize. If correct, type Y to continue.
SUPER P4SCT/P4SCT+/P4SCT+II User's Manual Rebuilding Arrays *Note 1: Rebuilding applies to Fault Tolerant array (RAID 1) only. If an array Build process (or initialization) is interrupted or critical with one member missing, you must perform a Rebuild to optimized its functionality. For a critical array Rebuild operation, the optimal drive is the source drive. *Note 2: If no spare array exists and a hard disk drive fails, you need to create a spare before you can rebuild an array.
Appendix C: Software Installation Instructions Using the Disk Utilities The Disk Utilities enable you to format or verify the media of your Serial ATA hard disks. To access the disk utilities: 1. Turn on your computer and press Ctrl+A when prompted to access the ARC utility (as shown in the screen below.
SUPER P4SCT/P4SCT+/P4SCT+II User's Manual 2. From the ARC menu, select Disk Utilities as shown in the screen below. 3 Select the desired disk and press Enter (as shown in the screen below.
Appendix C: Software Installation Instructions You can choose from the following options: 1. Format Disk—Simulates a low-level format of the hard drive by writing zeros to the entire disk. Serial ATA drives are low-level formatted at the factory and do not need to be low-level formatted again. (*Caution: Formatting destroys all data on the drive. Be sure to back up your data before performing this operation.) 2. Verify Disk Media—Scans the media of a disk drive for defects.
SUPER P4SCT/P4SCT+/P4SCT+II User's Manual C-2 Installing Intel's Hance Rapids Driver by Adaptec and the OS a. Insert Supermicro's bootable CD that came with the package into the CD Drive during the system reboot, and the screen:"Super Micro Driver Diskette Maker" will appear. b. Choose from the list the item: "Intel Hance Rapids Driver by 3rd Party (Adaptec)" and press . c. From the next screen displayed, choose the OS driver you want to install and press . d.
Appendix C: Software Installation Instructions C-3 Installing Other Software Programs and Drivers A. Installing Drivers other than Adaptec Embedded Serial ATA RAID Controller Driver After you've installed Windows Operating System, a screen as shown below will appear. You are ready to install software programs and drivers that have not yet been installed. To install these software programs and drivers, click the icons to the right of these items.
SUPER P4SCT/P4SCT+/P4SCT+II User's Manual Supero Doctor III The Supero Doctor III program is a Web base management tool that supports remote management capability. It includes Remote and Local Management tools. The local management is called SD III Client. The Supero Doctor III program included on the CDROM that came with your motherboard allows you to monitor the environment and operations of your system.
Appendix C: Software Installation Instructions Supero Doctor III Interface Display Screen-II (Remote Control) (*Note: SD III Software Revision 1.0 can be downloaded from our Web site at: ftp://ftp.supermicro.com/utility/Supero_Doctor_III/. You can also download SDIII User's Guide at: http://www.supermicro.com/PRODUCT/ Manuals/SDIII/UserGuide.pdf. For Linux, we will still recommend Supero Doctor II.
SUPER P4SCT/P4SCT+/P4SCT+II User's Manual Notes C-24