Quick reference (1.0)

ManualsBrandsSupermicro ManualsServerSSF627R3-R72B+

http://www.supermicro.com MNL-1416-QRG

Board Layout

SuperServer F627R3-RTB+/R72B+ Quick Reference Guide

CPU Installation

Front View & Interface

Heatsink Installation

1. Place the heatsink on top of the installed CPU.

2. Align the four screws to the socket.

3. Holding the heatsink in place, screw down as shown

(cross pattern, in order: A, C, B, D).

4. Note: Only use 6-8 lb/f of torque; otherwise, hand-tighten

each screw to avoid damaging the CPU.

Memory

Caution

SAFETY INFORMATION

IMPORTANT: See installation instructions and safety warning

before connecting system to power supply.

http://www.supermicro.com/about/policies/safety_information.cfm

WARNING:

To reduce risk of electric shock/damage to equipment,

disconnect power from server by disconnecting all power

cords from electrical outlets.

If any CPU socket empty, install protective plastic CPU cap

CAUTION:

Always be sure all power supplies for this system have

the same power output. If mixed power supplies are

installed, the system will not operate.

For more information go to :

http://www.supermicro.com/support



Rear View

Power Button

LAN LED

Information LED

UID Button

Description

No.

Description

No.

Micro-Low Profile Card

Low-Profile PCI-E Expansion Slot

Dedicated LAN for IPMI

GbE LAN1/LAN2 Ports

VGA Port

USB 0/1 Ports

Power Supply Module



Align CPU to socket;

install CPU straight down

NOTE:

Do not bend pin inside socket



SNK-P0048P for CPU1

Node 2

Node 4

Node 1

Node 3

Node Locations in the Chassis

Node 2

Controls six front 3.5" HDDs, B1-B6

and two rear 3.5" HDDs B7-B8

Node 4

Controls six front 3.5" HDDs, D1-D6

and two rear 3.5" HDDs D7-D8

Node 1

Controls six front 3.5" HDDs, A1-A6

and two rear 3.5" HDDs A7-A8

Node 3

Controls six front 3.5" HDDs, C1-C6

and two rear 3.5" HDDs C7-C8

SNK-P0048PS for CPU2

Screw #D

Screw #A

Screw #C

Screw #B

Screw #D

Screw #A

Screw #C

Screw #B

Processors and Memory Module Population for Optimal Performance

Number of

CPUs + DIMMs

CPU and Memory Population Configuration Table

(For memory to work properly, follow the instructions below)

1 CPU & 2 DIMMs

CPU1 & P1-DIMMA1/P1-DIMMB1

1 CPU & 4 DIMMs

1 CPU & 5~8 DIMMs

2 CPUs & 4 DIMMs

2 CPUs & 6 DIMMs

CPU1 & P1-DIMMA1/P1-DIMMB1, P1-DIMMC1/P1-DIMMD1

CPU1 & P1-DIMMA1/P1-DIMMB1, P1-DIMMC1/P1-DIMMD1 + Any memory pairs in P1-DIMMA2/P1-DIMMB2/

P1-DIMMC2/P1-DIMMD2 slots

CPU1 + CPU2 & P1-DIMMA1/P1-DIMMB1, P2-DIMME1/P2-DIMMF1

CPU1 + CPU2 & P1-DIMMA1/P1-DIMMB1/P1-DIMMC1/P1-DIMMD1, P2-DIMME1/P2-DIMMF1

2 CPUs & 8 DIMMs

2 CPUs & 10~16 DIMMs

2 CPUs & 16 DIMMs

CPU1 + CPU2 & P1-DIMMA1/P1-DIMMB1/P1-DIMMC1/P1-DIMMD1, P2-DIMME1/P2-DIMMF1/P2-DIMMG1/P2-DIMMH1

+ Any memory pair in P1, P2 DIMM slots

CPU1 + CPU2 & P1-DIMMA1/P1-DIMMB1/P1-DIMMC1/P1-DIMMD1, P2-DIMME1/P2-DIMMF1/P2-DIMMG1/P2-DIMMH1,

P1-DIMMA2/P1-DIMMB2/P1-DIMMC2/P1-DIMMD2, P2-DIMME2/P2-DIMMF2/P2-DIMMG2/P2-DIMMH2

Processors and their Corresponding Memory Modules

CPU#

Corresponding DIMM Modules

CPU 1

P1-DIMMA1

CPU 2 P2-DIMME1

P1-DIMMB1

P2-DIMMF1

P1-DIMMD1

P2-DIMMH1

P1-DIMMA2

P2-DIMME2

P1-DIMMB2

P2-DIMMF2

P1-DIMMD2

P2-DIMMH2

P1-DIMMC2

P2-DIMMG2

P1-DIMMC1

P2-DIMMG1

Intel E5-2600 v2 Series Processor RDIMM Memory Support

Ranks per DIMM

Data Width

Memory Capacity

Per DIMM

(See the Note below)

Speed (MT/s) and Voltage Validated by Slot per

Channel (SPC) and DIMM Per Channel (DPC)

SRx8

2 Slots Per Channel

1DPC

1.35V

1.5V

1GB 2GB

4GB

DRx8

SRx4

DRx4

QRx4

2GB 4GB

8GB

2GB 4GB

8GB

4GB 8GB 16GB

8GB 16GB 32GB

1066, 1333

1066, 1333, 1600, 1866

1066, 1333

1066, 1333, 1600, 1866

1066, 1333

1066, 1333, 1600, 1866

1066, 1333

1066, 1333, 1600, 1866

800

800, 1066

Installing RDIMM Memory

QRx8

4GB 8GB 16GB

800

800, 1066

Intel E5-2600 v2 Series Processor UDIMM Memory Support

Ranks per DIMM

& Data Width

Memory Capacity

Per DIMM

(See the Note below)

Speed (MT/s) and Voltage Validated by Slot per

Channel (SPC) and DIMM Per Channel (DPC)

SRx8 Non-ECC

2 Slots Per Channel

1DPC

1.35V

1.5V

1GB 2GB 4GB

DRx8 Non-ECC

SRx16 Non-ECC

SRx8 ECC

QRx8 ECC

2GB 4GB 8GB

512MB 1GB 2GB

1GB 2GB 4GB

2GB 4GB 8GB

1066, 1333, 1600, 1866

1066, 1333

1066, 1333, 1600, 1866

1066, 1333

1066, 1333, 1600, 1866

Installing UDIMM (ECC/non-ECC) Memory

1.35V

1066, 1333

1066, 1333, 1600

1066, 1333

1066, 1333, 1600

1066, 1333

1066, 1333, 1600

1066, 1333

1066, 1333, 1600

800

1.5V

2DPC

1.35V

1.5V

1066, 1333, 1600

1066, 1333

1066, 1333, 1600

1066, 1333

1066, 1333, 1600

2DPC

ÌMNL-1416-QRGnÎ

Nodes and Corresponding Hard Drives

Description

No.

P2-DIMMF1 (Blue Slot) / DIMMF2

CPU2 Socket

P2-DIMMH1 (Blue Slot) / DIMMH2

P2-DIMMG1 (Blue Slot) / DIMMG2

CPU1 Slot1 PCI-E 3.0 x8 Slot

for SMC-Proprietary Add-On Card

P1-DIMMB1 (Blue Slot) / DIMMB2

P1-DIMMA1 (Blue Slot) / DIMMA2

JSD2: Disk-On-Module power

connector

I-SATA 0/1: SATA 3.0 Ports

Description

No.

CPU1 Slot1 PCI-E 3.0 x8 Micro Low-Profile

I-SATA2~5: SATA 2.0 Ports

S-SATA0~1: SATA 2.0 Ports

JBT1: CMOS Clear

CPU1 Slot1 PCI-E 3.0 x16

JTPM1: Trusted Platform Module Header

CPU1 Socket

P1-DIMMC1 (Blue Slot) / DIMMC2

P1-DIMMD1 (Blue Slot) / DIMMD2

10 P2-DIMME1 (Blue Slot) / DIMME2

PCH

USB1

COM1

LAN2

JSD1

S-SATA1

I-SATA3

I-SATA4

I-SATA2

JTPM1

FAN1

FAN2

FAN3

J21

LED1

JITP0

P1-DIMMB2

P2-DIMMH2

P1-DIMMB1

P1-DIMMA2

P2-DIMMH1

P2-DIMME1

CPU1

P1-DIMMC1

P2-DIMMG2

P1-DIMMA1

ALWAYS POPULATE DIMMx1 FIRST

P1-DIMMC2

P2-DIMME2

P2-DIMMG1

P2-DIMMF1

P1-DIMMD2

P1-DIMMD1

P2-DIMMF2

JBAT1

LAN1

CPU2

BIOS

BMC

IPMI

_LAN

X9DRFR

USB2

I-SATA5

S-SATA0

T-SGPIO1

T-SGPIO2

JBT1

S-SATA2

S-SATA3

I-SATA1

I-SATA0

JSD2

VGA1

1314

1011