User's Manual (1.0b)

2-16
X10QBi Platform User's Manual
SMI Slot P1M1
Installing Memory Cards on
the Baseboard
1. The X10QBi baseboard supports
eight memory slots for eight X10QBi-
MEM1 memory cards with two
memory cards per CPU. Please refer
the table below.
2. Each X10QBi-MEM1 memory card
supports up to 12 modules of DDR3
ECC RDIMM/LRDIMM memory of
up to 1600 MHz. With eight cards
installed on the baseboard, the
X10QBi supports up to 96 modules
with a total size of 6TB supported.
2-6 Memory Support for the X10QBi Platform
X10QBi-MEM1
PRESENT_LED1
DIMM2A_LED3
DIMM1A_LED2
DIMM0A_LED1
DIMM2B_LED6
DIMM1B_LED5
DIMM0B_LED4
DIMM2C_LED1 DIMM1C_LED8
DIMM0C_LED7
DIMM2D_LED4
DIMM1D_LED3
DIMM0D_LED2
BAR CODE
A3
D1D2C1C2C3 D3
OK
B1B2B3A1A2
JDI
JDI
DIMMC3
DIMMA1 DIMMA2
DIMMA3
DIMMB3
DIMMB2
DIMMB1
Rev. 1.01
DIMMC2
DIMMC1
DIMMD3
DIMMD2
DIMMD1
A1
A2
A3
B1
B2
B3
C1
C3
D1
D2
D3
C2
X10QBi
Rev:1.02
MAC CODE
BAR CODE
MAC CODE
SMI Slot P1M2
SMI Slot P2M1 SMI Slot P2M2
SMI Slot P3M1 SMI Slot P3M2
SMI Slot P4M1
SMI Slot P4M2
3. When installing a DIMM module on a memory card, be sure to press the
module straight down into the slot until it is properly seated and the PRES-
ENT_LED is on. Also, be sure to always install the DIMM modules in the blue
slots rst, starting with DIMMA1/DIMMB1/DIMMC1/DIMMD1.
Installing Memory Cards to the Baseboard
After populating DIMMs on the memory cards, follow the table below to install the
memory cards that are populated with DIMM modules on the baseboard:
CPUs and the Corresponding Memory Cards
CPU# Corresponding DIMM Modules
No. of card(s) for
Each CPU
One (1) Memory Card for each CPU Installed
on the baseboard
Two (2) Memory Cards for each
CPU Installed on the baseboard
CPU 1 SMI Slot P1M1 SMI Slot P1M1 + SMI Slot P1M2
CPU 2 SMI Slot P2M1 SMI Slot P2M1 + SMI Slot P2M2
CPU 3 SMI Slot P3M1 SMI Slot P3M1 + SMI Slot P3M2
CPU 4 SMI Slot P4M1 SMI Slot P4M1 + SMI Slot P4M2
Note 1: For proper memory installation on the memory card, please always
populate the blue slots rst, starting with DIMMA1,DIMM B1, DIMMC1 and
then DIMMD1.
Note 2: To optimize system performance, we recommend that the 4-CPU
conguration be used in your system (either with full-loading of 96 memory
modules installed or half-loading with 48 modules installed.) Please also
note that the 1-CPU conguration has not been validated by Supermicro.
PRESENT_LED