User's Manual (1.0b)

Chapter 2: Installation
2-27
X10QBi
Rev:1.02
MAC CODE
BAR CODE
M*M*M*M*M*M*
FAN5
FAN10
FAN7
FAN6
FAN8
FAN9
FAN1
FAN4
FAN2
FAN3
JPW2
JPW6
JPW7
JPW3
JPW4
JPW5
LED_PORT80
JM2
JM5
JLPC1
JP2
BT2
SP1
JP3
JL1
J17
JOH1
JI2C2
LED28
LED23
LED2
LED1
LED15
LED19
LED22
LED18
D40
JBT1
LED35
LED10
LED9
LED8
LED14
LED7
LED12
LED13
LED11
LEDIO1
LED3
JSD1
JP1JP5
JPME2
JPME1
JWD1
JPT1
JWP1
JXDP3
JXDP2
JVRM_I2C1
JVRM_I2C2
JXDP1
JIPMB1
JPI2C1
JD1
T-SGPIO1
T-SGPIO2
I-SATA0
I-SATA1
I-SATA2
I-SATA5
I-SATA4
I-SATA3
JF1
JIO1
SMI SLOT P4M1
SMI SLOT P3M2
SMI SLOT P3M1
SMI SLOT P2M2
SMI SLOT P2M1
SMI SLOT P1M2
SMI SLOT P4M2
SMI SLOT P1M1
CPU4
CPU3
CPU1
USB6/7
USB2/3
USB4
COM2
CPU4 SLOT8 PCI-E 3.0 X8
CPU4 SLOT10 PCI-E 3.0 X8
CPU4 SLOT11 PCI-E 3.0 X16
CPU3 SLOT7 PCI-E 3.0 X8
CPU3 SLOT6 PCI-E 3.0 X8
CPU3 SLOT9 PCI-E 3.0 X16
CPU2 SLOT5 PCI-E 3.0 X8
CPU2 SLOT3 PCI-E 3.0 X8
CPU1 SLOT2 PCI-E 3.0 X16
CPU1 SLOT1 PCI-E 3.0 X8
SIO SLOT
CLOSE 1st
OPEN 1st
CPU2
USB0/1
JI2C1
CLOSE 1st
OPEN 1st
CLOSE 1st
OPEN 1st
CLOSE 1st
OPEN 1st
M*
M*
M* M*
M*
M*
M*
M*
MAC CODE
JPW1
CPU2 SLOT4 PCI-E 3.0 X16
USB5
2-8 Connecting Cables
A. JPW1: 24-pin ATX PWR (Req'd)
B. JPW2: 8-pin PWR (Req'd)
C. JPW3: 8-pin PWR (Req'd)
D. JPW4: 8-pin PWR (Req'd)
E. JPW5: 8-pin PWR (Req'd)
F. JPW6: 8-pin PWR (Req'd)
G. JPW7: 8-pin PWR (Req'd)
H. JSD1: SATA Device PWR (Req'd for
SATA devices)
A
B
C
D
E
F
G
H
DOM Power Connector
A power connector for SATA DOM (Disk-On-
Module) devices is located at JSD1. Con-
nect the appropriate cable here to provide
power support for your SATA DOM devices.
DOM PWR
Pin Denitions
Pin# Denition
1 +5V
2 Ground
3 Ground
Warning: To provide adequate power supply to
the system, be sure to connect the 24-pin ATX
PWR (JPW1) and six 8-pin PWR connectors
(JPW2-JPW7) to the power supply. Failure to
do so will void the manufacturer warranty on
your power supply and motherboard.
Power Connectors
A 24-pin main power supply connector(JPW
1) and six 8-pin power connectors (JPW2-
JPW7) are located on the X10DBi moth-
erboard. These power connectors meet
the SSI EPS 12V specication. Be sure to
connect these power connectors to your
power supply to provide adequate power to
your system. Refer to the table on the right
for pin denitions.
ATX Power 24-pin Connector
Pin Denitions
Pin# Denition Pin # Denition
13 +3.3V 1 +3.3V
14 -12V 2 +3.3V
15 COM 3 COM
16 PS_ON 4 +5V
17 COM 5 COM
18 COM 6 +5V
19 COM 7 COM
20 Res (NC) 8 PWR_OK
21 +5V 9 5VSB
22 +5V 10 +12V
23 +5V 11 +12V
24 COM 12 +3.3V
12V 8-pin PWR Con-
nector
Pin Denitions
Pins Denition
1 through 4 Ground
5 through 8 +12V
(Required)