User's Manual (1.0b)
Chapter 2: Installation
2-35
X10QBi
Rev:1.02
MAC CODE
BAR CODE
M*M
*
M*M*M*M
*
FAN5
FAN10
FAN7
FAN6
FAN8
FAN9
FAN1
FAN4
FAN2
FAN3
JPW2
JPW6
JPW7
JPW3
JPW4
JPW5
LED_PORT80
JM2
JM5
JLPC1
JP2
BT2
SP1
JP3
JL1
J17
JOH1
JI2C2
LED28
LED23
LED2
LED1
LED15
LED19
LED22
LED18
D40
JBT1
LED35
LED10
LED9
LED8
LED14
LED7
LED12
LED13
LED11
LEDIO1
LED3
JSD1
JP1JP5
JPME2
JPME1
JWD1
JPT1
JWP1
JXDP3
JXDP2
JVRM_I2C1
JVRM_I2C2
JXDP1
JIPMB1
JPI2C1
JD1
T-SGPIO1
T-SGPIO2
I-SATA0
I-SATA1
I-SATA2
I-SATA5
I-SATA4
I-SATA3
JF1
JIO1
SMI SLOT P4M1
SMI SLOT P3M2
SMI SLOT P3M1
SMI SLOT P2M2
SMI SLOT P2M1
SMI SLOT P1M2
SMI SLOT P4M2
SMI SLOT P1M1
CPU4
CPU3
CPU1
USB6/7
USB2/3
USB4
COM2
CPU4 SLOT8 PCI-E 3.0 X8
CPU4 SLOT10 PCI-E 3.0 X8
CPU4 SLOT11 PCI-E 3.0 X16
CPU3 SLOT7 PCI-E 3.0 X8
CPU3 SLOT6 PCI-E 3.0 X8
CPU3 SLOT9 PCI-E 3.0 X16
CPU2 SLOT5 PCI-E 3.0 X8
CPU2 SLOT3 PCI-E 3.0 X8
CPU1 SLOT2 PCI-E 3.0 X16
CPU1 SLOT1 PCI-E 3.0 X8
SIO SLOT
CLOSE 1st
OPEN 1st
CPU2
USB0/1
JI2C1
CLOSE 1st
OPEN 1st
CLOSE 1st
OPEN 1st
CLOSE 1st
OPEN 1st
M
*
M*
M* M*
M*
M*
M*
M*
MAC CODE
JPW1
CPU2 SLOT4 PCI-E 3.0 X16
USB5
CMOS Clear
JBT1 is used to clear the CMOS. Instead of pins, this "jumper" consists of contact
pads to prevent the accidental clearing of the CMOS. To clear the CMOS, use a
metal object such as a small screwdriver to touch both pads at the same time to
short the connection. Always remove the AC power cord from the system before
clearing the CMOS.
Note 1. For an ATX power supply, you must completely shut down the sys-
tem, remove the AC power cord, and then short JBT1 to clear the CMOS.
Note 2. Be sure to remove the onboard CMOS Battery before you short
JBT1 to clear the CMOS.
Note 3. Clearing the CMOS will also clear any passwords.
A
B
A. Clear CMOS
B. Watch Dog Enable
Watch Dog Enable/Disable
Watch Dog (JWD1) is a system monitor that can
reset the system when a software application
hangs. Close pins 1-2 to reset the system if an
application hangs. Close pins 2-3 to generate a
non-maskable interrupt signal for the applica-
tion that hangs. Refer to the table on the right
for jumper settings. Watch Dog must also be
enabled in the BIOS.
Watch Dog
Jumper Settings
Jumper Setting Deî‚żnition
Pins 1-2 Reset (default)
Pins 2-3 NMI
Open Disabled