User Manual
Table Of Contents
- Preface
- Chapter 1 Introduction
- Chapter 2 Installation
- 2-1 Standardized Warning Statements
- 2-2 Static-Sensitive Devices
- 2-3 Motherboard Installation
- 2-4 Memory Support
- 2-5 Connectors/IO Ports
- 2-6 Connecting Cables
- ATX PWR, DC PWR and HDD PWR Connectors (JPW1, PJ1, J6)
- Fan Headers (FAN1 ~ FAN4) (FAN4 is available on PCB 2.00 only)
- Chassis Intrusion
- System Management Bus Header
- DOM PWR Connector
- TPM Header/Port 80 Header
- Overheat LED Header
- Speaker
- Standby Power
- I-SGPIO1/I-SGPIO2
- NVMe I2C Header
- Power SMBus (I2C) Connector (available on PCB 2.00 only)
- System Management Bus Header
- GPIO Header
- ATX PWR, DC PWR and HDD PWR Connectors (JPW1, PJ1, J6)
- 2-7 Jumper Settings
- 2-8 Onboard Indicators
- 2-9 SATA Connections
- Chapter 3 Troubleshooting
- Chapter 4 BIOS
- Appendix A BIOS Error Beep Codes
- Appendix B Software Installation Instructions
- Appendix C UEFI BIOS Recovery Instructions
- Appendix D Dual Boot Block
vii
Universal Serial Bus (USB) ...................................................................... 2-12
Unit Identier Switch ................................................................................ 2-13
VGA .......................................................................................................... 2-13
Front Control Panel ....................................................................................... 2-14
Front Control Panel Pin Denitions............................................................... 2-15
Power LED .............................................................................................. 2-15
Overheat (OH)/Fan Fail/PWR Fail/UID LED ............................................ 2-15
HDD LED .................................................................................................. 2-16
NIC1/NIC2 (LAN1/LAN2) .......................................................................... 2-16
Reset Button ........................................................................................... 2-17
Power Button ........................................................................................... 2-17
Power Fail LED (Available on PCB 2.00 only) ....................................... 2-18
2-6 Connecting Cables ........................................................................................ 2-19
ATX PWR, DC PWR and HDD PWR Connectors (JPW1, PJ1, J6) ........ 2-19
Fan Headers (FAN1 ~ FAN4) (FAN4 is available on PCB 2.00 only) ..... 2-20
Chassis Intrusion ..................................................................................... 2-20
System Management Bus Header ........................................................... 2-21
DOM PWR Connector .............................................................................. 2-21
TPM Header/Port 80 Header ................................................................... 2-22
Overheat LED Header .............................................................................. 2-22
Speaker .................................................................................................... 2-23
Standby Power ......................................................................................... 2-23
I-SGPIO1/I-SGPIO2 ................................................................................. 2-24
NVMe I2C Header .................................................................................... 2-24
Power SMBus (I
2
C) Connector (available on PCB 2.00 only) ................. 2-25
System Management Bus Header ........................................................... 2-25
GPIO Header ............................................................................................ 2-26
2-7 Jumper Settings ............................................................................................ 2-27
Explanation of Jumpers ................................................................................ 2-27
VGA Enable .............................................................................................. 2-27
CMOS Clear ............................................................................................. 2-28
PCI-E Slot SMB Enable (I
2
C1/I
2
C2) ......................................................... 2-28
Watch Dog Timer Enable ......................................................................... 2-29
USB Wake-Up ......................................................................................... 2-29
Management Engine (ME) Recovery ...................................................... 2-30
ME Manufacturing Mode .......................................................................... 2-30
Gigabit LAN Ports Enable/Disable (on -F, -LN2F, -TLN4F models) ....... 2-31
10G LAN Ports Enable/Disable (on -TLN2F and -TLN4F models) .......... 2-31
BIOS Recovery ......................................................................................... 2-32
Table of Contents