Datasheet

2-32
X7DBi+ User's Manual
JPG1
JPL2
JPL1
J29
J30
J28
J27
JOH1
JAR
J3P
WOR
JL1
JK1
JCF1
JWF1
LE1
JBT1
FAN7
FAN5
FAN8
FAN3
FAN4
FAN6
JD1
FAN2
FAN1
Printer
VGA
24-Pin ATX PWR
4-Pin PWR
8-Pin PWR
FP CTRL
Buzzer
ESB 2
(North Bridge)
5000P
Bank2
(SouthBridge)
DIMM 1D (Bank1)
DIMM 2A (Bank2)
DIMM 2B (Bank2)
DIMM 2C (Bank2)
DIMM 2D (Bank2)
DIMM 3A (Bank3)
DIMM 3B (Bank3)
DIMM 3C (Bank3)
DIMM 3D (Bank3)
DIMM 4A (Bank4)
DIMM 4B (Bank4)
DIMM 4C (Bank4)
DIMM 4D (Bank4)
Intel
Intel
X7DBi+
CPU2
CPU1
GLAN
CTRL
VGA
CTRL
VGA
Memory
Slot4 PCI-E X8
Slot3 PCI-E X4
Battery
CPU FAN1
PSF
SMBus PS
GLAN1
Bank1
GLAN2
Slot7 SIMLP
CPU FAN2
Compact Flash
IDE#1
Floppy
Slot6 PCI-E X8
Slot2 PCI-E X4
JWD
Slot1 PCI-X 133MHZ
USB 4
WOL
USB 2/3
KEYLOCK
SMB
I-SATA2
I-SATA0
I-SATA5
I-SATA4
I-SATA3
I-SATA1
USB 0/1
COM1
KB/Mouse
BIOS
SI/O
Slot5 PCI-E X4
Bank3
Bank4
DIMM 1A (Bank1)
DIMM 1B (Bank1)
DIMM 1C (Bank1)
IDE Drive Connectors
Pin Defi nitions
Pin# Defi nition Pin # Defi nition
1 Reset IDE 2 Ground
3 Host Data 7 4 Host Data 8
5 Host Data 6 6 Host Data 9
7 Host Data 5 8 Host Data 10
9 Host Data 4 10 Host Data 11
11 Host Data 3 12 Host Data 12
13 Host Data 2 14 Host Data 13
15 Host Data 1 16 Host Data 14
17 Host Data 0 18 Host Data 15
19 Ground 20 Key
21 DRQ3 22 Ground
23 I/O Write 24 Ground
25 I/O Read 26 Ground
27 IOCHRDY 28 BALE
29 DACK3 30 Ground
31 IRQ14 32 IOCS16
33 Addr1 34 Ground
35 Addr0 36 Addr2
37 Chip Select 0 38 Chip Select 1
39 Activity 40 Ground
IDE Connectors
There are two IDE Connectors (JIDE1:
Blue, JIDE2: White) on the mother-
board. The blue IDE connector (JIDE1)
is designated the Primary IDE Drive.
However, it also supports a compact
fl ash card. The white IDE connector
(JIDE2) is designated the Secondary
IDE Drive, reserved for Compact Flash
Card use only. (See the note below.)
See the table on the right for pin defi ni-
tions.
Note: JIDE2 (the white slot) is reserved
for Compact Flash Card only. Do not
use it for other devices. If JIDE2 is
populated with a Compact Flash Card,
JIDE1 (the blue slot) will be available for
one device only. For the Compact Flash
Card to work properly, you will need to
enable its corresponding jumper, and
connect a power cable to its corre-
sponding power connector fi rst.
A
B
A. IDE1
B.Compact Flash Card
Slot