User's and BIOS Manual (1.1)

2-36
X8SIA/X8SIA-F User's Manual
SP1
+
+
B1
JBT1
IPMB
JD1
JPW1
JPW2
JPI2C
JWOL
JWF1
JF1
FAN2
FAN1
FAN5
FAN3
FAN4
T-SGPIO1 T-SGPIO2
JI2C1
JI2C2
JWOR
JL1
3
JPUSB1
JLED
JPL1
JPL2
JPG1
LE1
C
C
LE7
J*
W83627DHG
IDT
89HI0524G2PS
PCH
Hermon
SLOT7 PCI-E 2.0 (2.5GT/s) X1
SLOT6 PCI-E 2.0
SLOT5 PCI-E 2.0 X8
SLOT4 PCI-E 2.0 X8
SLOT3 PCI-E 2.0 (2.5GT/s) X1
USB8/9
FAN2/CPUFAN
USB4
USB5
FAIL PWR
DOM PWR
JWOL:
I-SATA4
I-SATA3
UID
DIMM2A
DIMM2BDIMM2CDIMM1B DIMM1A
Chassis Intrusion
Wake on Lan
Wake on Ring
CMOS CLEAR
1-2:ENABLE
2-3:DISABLE
JPL2:LAN2
JPL1:LAN1
2-3:DISABLE
1-2:ENABLE
JPB:BMC
JPI2C:PWR I2C
JSPK:Buzzer/Speaker
COM2
FLOPPY
DDR3 1066/1333 UDIMM/RDIMM required
JL1:
LAN1/LAN2
JPUSB1:B/P USB WAKE UP
1-2:ENABLE
2-3:DISABLE
JI2C1/JI2C2
USB6/7
2-3:Disable 1-2:Enable
CPU
JLED:Power LED
OFF:Disable
ON:Enable
2-3:DISABLE
1-2:ENABLE
JF1
ON
LED LED
PWRHDD
NIC1
NIC2
OH/FF
RST
PWR
I-SATA2
I-SATA1
I-SATA0
I-SATA5
SLOT2 PCI-E 2.0 (2.5GT/s) X4 (IN X8 SLOT)
SLOT1 PCI 33MHz
DIMM1C
JPG1: VGA
KB/MOUSE
VGA
COM1
IPMI_LAN
USB0/1 USB2/3
X8SIA
A
A. BP USB 0/1 Wake-up
B. BMC Jumper
USB Wake-Up
Use the JPUSB1 jumper to "wake-up" your
system by pressing a key on a USB keyboard
or clicking the USB mouse. The JPUSB1
jumper is used together with the USB Wake-
Up feature in the BIOS. Enable this jumper
and the USB feature in the BIOS to wake-up
your system via USB devices.
Note: When the USB function is set to
Enabled in the BIOS, and a USB Wake-
up jumper is set to Disabled, remove the
USB devices from the USB ports whose
USB jumper is Disabled before the sys-
tem goes into the standby mode.
JPUSB1 (BackPanel USB
0/1/2/3 Wake-up Enable)
Pin# Denition
1-2 Enabled (Default)
2-3 Disabled
B
BMC Jumper (X8SIA-F Only)
JPB is used to enable or disable the BMC
(Baseboard Management Control) Chip and
the onboard IPMI connection. This jumper is
used together with the IPMI settings in the
BIOS. The default position is on pins 1 and
2 to enable BMC. See the table on the right
for jumper settings.
BMC IPMI Enable/Disable Jumper
Settings
Settings Denition
Pins 1-2 Enabled (Default)
Pins 2-3 Disabled