Installation Instructions

ManualsBrandsSupervent ManualsHeating & Cooling6" Trim Collar Class A Vent

Install first Wall

Band 3 feet

above Wall

Support, and add

one Wall Band

every 8 feet there

after.

If the Chimney

extends 5 feet

or more above

the roof you

must install a

Universal Roof

Guy Kit.

A minimum of

ONLY 6" is

required between

the Ceiling/Wall

and Double Wall

Stove Pipe, or 18"

for Single Wall

Stove Pipe.

* If a wood burning appliance is used every day in the heating

season, surveys have shown that a single wall stove wall pipe

will need replacement every two or three years.

Single Wall

Stove Pipe

*No

Warranty

18 Inches

Light Guage

Carbon Steel

Not Tested

or Labeled

DOUBLE WALL vs SINGLE WALL STOVE PIPE

Product

Warranty

Clearances to

Combustibles

Material

Tested &

Labeled

Model DSP

Double Wall

Stove Pipe

Lifetime

Warranty

6 Inches

Heavy Guage

Stainless Steel /

Aluminized

Steel

ULC S641 /

UL 103

NOTE:

All SuperVent

products are color

coded for your

convenience!

6" Diameter

8" Diameter

Firestop Radiation Shield

(Joist Shield) must be

installed when the chimney

passes from a lower living

space into an upper living

space.

Note: You must enclose all

sections of the chimney when

it passes through accessible

living areas. SuperVent

chimney requires ONLY 2" of

clearance to combustibles.

Getting Started

Before you begin, determine the (inner)

diameter of your Chimney.

This is usually the

same size (6" or 8") as

the flue collar on your

wood stove.

Tee requires a

chimney length

to go through

the wall, and it

must extend a

minimum of 3"

into the room.

Attic Insulation Shield

UL-103 HT

Standard

rox tApp . 8 f .

Approx. ft.8

oAppr x. 8 ft.

.Min. 3 ft

If an offset is required

to avoid rafters or

other obstructions,

measure the

horizontal distance

required and the

vertical height

available, refer to the

Chimney Offset Chart

to determine the

Elbows and Chimney

Length required.

Step 4

Offset Calculation for Ceiling Support Installations Only

A: Offset

B: Height

Choose the proper Roof Flashing required for your installation.

To determine which Roof Flashing you require, work out the pitch of your roof.

ROOF FLASHING SELECTION CHART

6" Chimney Diameter:

0/12 - 6/12 Roof Pitch=

6/12 - 12/12 Roof Pitch=

8" Chimney Diameter:

0/12 - 6/12 Roof Pitch=

6/12 - 12/12 Roof Pitch=

637-1539

637-1665

- (Low Slope)

- (Steep Slope)

- (Low Slope)

- (Steep Slope)

NOTE: for Metal Roofs use:

Universal Rubber Boot Flashing Kit=

637-1704

637-1830

200275

To calculate your

roof pitch use one

of the 12 inch rulers

to measure the

number of inches

(A) from the end of

the other ruler down

to the roof.

1 2 3 4 5 6 7 8 9 10 11

(A)

For example: If (A)

equals 3" then the roof

pitch is 3/12.

Step 3

3' min.

10'

The chimney must extend at least 3' above the highest

point where it passes through the roof surface and at

least 2' higher than any part of the building within a

horizontal distance of 10'.

Determine the number of Chimney Lengths

required. Chimney Lengths are available in 36",

24", 18", 12" and 6" lengths.

NOTE: When calculating

the installed length of

your chimney subtract

1-1/8" for each joint &

include the Height

Requirements as shown

in this illustration.

HEIGHT

REQUIREMENTS

Step 2

Step 5

6 " Diameter 8" Diameter

Elbow Chimney Lengths A B A B

2 x 15 no chimney length 1-1/8" 10" 1-1/4" 10-3/8"

2 x 15 6" chimney length 2-3/8" 14-1/4" 2-1/2" 15-5/8"

2 x 15 12" chimney length 4" 20-1/2" 4-1/8" 21"

2 x 15 24" chimney length 7" 32" 7-1/8" 32-1/2"

2 x 15 36" chimney length 10-1/4" 43-5/8" 10-1/4" 44-1/8"

2 x 30 no chimney length 2-3/4" 11-5/8" 3-1/2" 14-1/2"

2 x 30 6" chimney length 5-1/4" 15-7/8" 6" 18-3/8"

2 x 30 12" chimney length 8-1/4" 21" 9" 24"

2 x 30 24" chimney length 14-1/4" 31-3/8" 15" 32-3/8"

2 x 30 36" chimney length 20-1/4" 41-7/8" 21" 44-3/4"

CHIMNEY OFFSET CHART



The final step required to complete your Wood Stove Venting solution is to determine the Model DSP Double Wall

Stove Pipe parts that will be needed to complete your installation. (Refer to Installation Diagrams (Step 1) and

complete your Installation Planning Work Sheet)

Your Complete Wood Stove Venting Solution

Helpful Installation Tips

Factory Built

Wood Stove

Chimney &

Double Wall

Stove Pipe

Factory Built

Wood Stove

Chimney &

Double Wall

Stove Pipe

Listed

kÉÉÇ=eÉäé\=KKK`çåí~Åí=ìë=~íW

çêIîáëáí=ìë=çåäáåÉ=@

1.800.252.8467

www.supervent.com

R&B #3802-0117(CR) Menards

Reduce, Reuse, Recycle

Our literature is printed on

recyclable paper

Attic Insulation Shield

must be installed when

the chimney passes

from a lower living

space into an upper

living space.

Summary of content (21 pages)

PAGE 1
Your Complete Wood Stove Venting Solution Step 2 Helpful Installation Tips Determine the number of Chimney Lengths required. Chimney Lengths are available in 36", 24", 18", 12" and 6" lengths. The chimney must extend at least 3' above the highest point where it passes through the roof surface and at least 2' higher than any part of the building within a horizontal distance of 10'.
PAGE 2
Complete Wood Stove Chimney & Double Wall Stove Pipe Step 1 Select type of installation by determining where your chimney will run. Decorator Ceiling Support Installation Decorator Ceiling Support Installation Two Story 1 3 2 6 12 16 Note: If your Chimney runs more than 50' you must install a Roof Support. SuperVent Spec. Order # JSC6RS or JSC8RS Cathedral Ceiling Support Installation 7 6 18 20 12 Note: If your Chimney runs more than 50' you must install a Roof Support. SuperVent Spec.
PAGE 3
U.S. INSTALLATION INSTRUCTIONS, WARRANTY AND MAINTENANCE GUIDE Selkirk Corporation 5030 Corporate Exchange Blvd., Grand Rapids, MI 49512 Toll Free: 1.800.433.6341 www.selkirkcorp.
PAGE 4
INSTALLATION INSTRUCTIONS & MAINTENANCE GUIDE & FACTORY BUILT TYPE HT INSULATED CHIMNEY Tested to UL103 Listed A MAJOR CAUSE OF CHIMNEY RELATED FIRES IS FAILURE TO MAINTAIN REQUIRED CLEARANCES (AIR SPACES) TO COMBUSTIBLE MATERIALS. IT IS OF THE UTMOST IMPORTANCE THAT THIS CHIMNEY BE INSTALLED ONLY IN ACCORDANCE WITH THESE INSTRUCTIONS. PLEASE READ ALL INSTRUCTIONS BEFORE BEGINNING YOUR INSTALLATION.
PAGE 5
TABLE OF CONTENTS TYPE OF APPLIANCES 4 PRE-INSTALLATION GUIDELINES 4 TOOLS 4 FRAMING DETAILS 5 CEILING SUPPORT INSTALLATION 5 STOVE PIPE ADAPTOR 5-6 ATTIC INSULATION SHIELD INSTALLATION 6 FIRESTOP JOIST SHIELD INSTALLATION 7 ELBOW INSTALLATION 7 ADJUSTABLE WALL SUPPORT INSTALLATION ADJUSTABLE INTERMEDIATE WALL SUPPORT CATHEDRAL CEILING SUPPORT INSTALLATION RAFTER RADIATION SHIELD INSTALLATION 8-9 9 9 - 10 10 ROOF SUPPORT INSTALLATION 10 - 11 ROOF FLASHING INSTALLATION 11 - 12 ROOF GU
PAGE 6
Authorities require that the chimney extend not less than 3 feet above the highest point where it passes through the roof of a building and not less than 2 feet above any portion of the building within 10 feet (see figure 1). See Chart 2 for Chimney Height Above the Roof on page 16 of these instructions.
PAGE 7
The SuperVent/SuperPro Ceiling Support will support up to 50 feet of chimney sections, all of which must be installed above the support. Figures 4 & 7 show the 2 most common types of Ceiling Support Installation. Frame (on all 4 sides) a level square opening to the dimensions specified in the Framing Dimension Table 1. FRAMING DETAILS: Plan your installation carefully. If possible, position the stove so that the flue outlet is between joists or rafters.
PAGE 8
flue pipe following the appliance manufacturer's installation instructions and appropriate building code requirements keeping in mind that the flue pipe run should be as short and straight as practicable. Generally, for a wood burning appliance installation, an 18" minimum clearance to combustibles must be maintained for a single wall flue pipe. The exception to this is a double wall stove pipe, such as Selkirk's Model DSP which can be installed at reduced clearances of 6" to combustibles.
PAGE 9
FIRESTOP JOIST SHIELD ELBOW INSTALLATION A Firestop Joist Shield (FRS) must be installed where the chimney passes from one living space to another living space, as shown in figure 8. It is designed to provide proper firestopping between floors and to keep direct radiation from the chimney away from the joist framing. One pair of (two) 15o or 30o Elbows may be used in an interior installation to provide an offset in order to avoid cutting of joists and to clear other obstructions.
PAGE 10
After framing in your opening to the dimensions specified (see Framing Dimensions Table 1) on page 5, install the exterior outer half (with the unfinished square plate) of the wall thimble into the outside wall opening. Secure in place with appropriate fasteners through the prepunched holes. ADJUSTABLE WALL SUPPORT As previously mentioned, the ideal location for your chimney system is within the building envelope. A Wall Support installation is required when the above mentioned location is not possible.
PAGE 11
If the chimney penetrates an eave or overhang (soffit) cut an opening with 2" clearance all around. To find the exact spot where the chimney will pass through the eaves, drop a plumb line from the underside of the eaves to the outer edge of the leveled chimney. Mark 5 or 6 points to give an outline of the hole. Remember that the hole will need 2" clearance to the chimney surface. Install an Attic Insulation Shield if space permits on the under side of the overhang.
PAGE 12
Once the box is at the desired position, ensure the box is level and nail the box to the framing using four 2” spiral nails or #8 x1-1/2" wood screws per side. The excess material sticking above the roof can either be trimmed off before attaching the box to the framing or, after it is installed the corners can be cut and the excess material folded down onto the roof deck.
PAGE 13
and the bottom edge OVER the shingles to provide a watershed. Trimming off the shingles may be neccessary around the cone of the Flashing for a better fit. Do not nail the flashing to the roof yet as adjustments may be required. Attach the support brackets to the support band with the 1/2” nuts, bolts and lock washers. The lock washer is placed between the band and support bracket to provide proper spacing as shown in Figure 16.
PAGE 14
The two telescopic legs should form an angle of about 60 degrees to give support to the chimney in all directions. Keep bottom ends equal distance from the chimney and if possible, at the same elevation, on the high side of the sloped roof. Seal the roof with a suitable non-hardening waterproof caulking. After the legs are attached to the chimney and bands, tighten the clamps on the legs to fix the position of the telescoping legs. (See Figure 20).
PAGE 15
UNIVERSAL ROOF GUY BAND (JURGK) ASSEMBLY INSTRUCTIONS 1. Measure the outside diameter of your chimney. 2. Mark the hole at each end of the band that corresponds to the diameter measured. These 2 holes along with the "Common" hole will be utilized for your particular chimney. 12" 11" 10" 9" 8" 7" Common 7" 8" 9" 10" 11" 12" 3. On the "Common" hole assemble 1 carriage bolt, 1 5/16" lock washer, 1 bracket, 1 1/4" lock washer and 1 1/4" hex nut in place as shown.
PAGE 16
MAINTENANCE AND CLEANING OF CHIMNEY: Contact a professional certified chimney sweep for chimney cleaning services and advice if you have any doubts about your ability to clean your chimney system or if the task is too large. To visually inspect the chimney, remove the Rain Cap by simply using the twist-lock feature. Care should be taken not to disengage any lower chimney sections. This will permit the insertion of a flashlight for inspection and a properly sized plastic chimney cleaning brush.
PAGE 17
CHART 1 - OFFSET CHIMNEY INSTALLATION It may be necessary to offset the chimney in order to clear a joist or an obstacle. The three (3) charts below will assist you in selecting the proper combination of elbow angle and chimney length(s) that will provide the necessary degree of offset within an available height. 1. Select the column with the proper chimney diameter of your system. 15o OFFSET CHART Chimney Lengths 5" Diameter A B 6" Diameter A B 7" Diameter A B 8" Diameter A B 2.
PAGE 18
CHART 2 - CHIMNEY HEIGHT ABOVE THE ROOF Requirement # 1 : The code requires that the chimney must extend at least 3 feet above the highest point of the roof that it penetrates. Requirement # 2 : It must also be 2 feet above any roof, wall or other obstruction within a horizontal distance of 10 feet. The following Chart is to assist you in determining the minimum chimney height you will require above the roof.
PAGE 19
REPLACEMENT PARTS LIST DESCRIPTION SUPERPRO PART No. SUPERVENT PART No.
PAGE 20
INSTALLATION INFORMATION Keep in a safe place for future reference CHIMNEY MODEL:__________________________________________ TYPE OF APPLIANCE:______________________________________ INSTALLATION DATE:_______________________________________ DESCRIPTION OF INSTALLATION (Chimney and Flue Pipe Configuration)___________________________________________ _________________________________________________________________________________________________________ __________________________________________________________
PAGE 21
“SMART CHOICE” LIMITED LIFETIME WARRANTY Selkirk Corporation, (“Selkirk”, “we”, “us”, “our”) warrants our residential Chimney & Venting products (* defined below) to be free from defects in material and workmanship. For products installed after January 1, 2009, for a period of Ten (10) years from original installation, we will provide replacement product with a similar or like quality of available Selkirk product, free of charge, excluding any installation costs.