UL 103-HT MODEL JSC INSULATED STAINLESS STEEL CHIMNEY FUEL GAS WOOD PRODUCT FEATURES OIL COAL SOLID PACK INSULATED STAINLESS STEEL (MIRROR FINISH) EMBOSSED COUPLER TWIST-LOCK CONNECTION
SuperVent Model JSC Technical Data Sheet CERTIFICATION & APPLICATIONS: CONSTRUCTION: SuperVent Model JSC is Safety Tested and Listed to applicable UL/ULC Standards. Inner Liner (Flue): •Upgraded Stainless Steel. •0.016" thickness Outer Casing: •Upgraded Stainless Steel •0.015" thickness Note: All SuperVent Twist-Lock Couplers are embossed (not lanced) and seams are weather-proofed to prevent moisture from entering the chimney.
Support Kits SuperVent has put together 3 chimney kits to get your project done . . . Model JSC has taken the guess work out of chimney installation by putting the most common parts for each installation all in one box. These 3 kits depict the most common installations. Simply decide which of these scenarios fits your need, then pick up your chimney lengths, roof flashing and elbows (if required). CEILING SUPPORT KIT “My chimney runs straight up through the ceiling.
Stainless Steel Chimney Lengths HEIGHT REQUIREMENTS 3' min. The chimney must extend at least three feet above the highest point where it passes through the roof surface and at least two feet higher than any part of the building within a horizontal distance of ten feet. 3' min. 10' 2' 2' Chimney Sections • Slim, advanced design allows for installation between 16" centers and still provides 2" clearance from combustible material.
Stainless Steel Tees & Elbows CHIMNEY OFFSET CHARTS This chart has three columns for elbow angle required to achieve your desired offset. The first column Offset (”Offset”) is the horizontal measurement, at the chimney center line, of the offset needed to get around an obstacle. The second column (”Height”) is the height of the assembled offset elbow to the top of the return elbow. Column 3 shows the appropriate lengths required. 1. Determine the distance of the offset required. Height 2.
Stainless Steel Tees & Elbows INSULATED TEE WITH PLUG • Insulated tee is for through the wall installation using a Wall Support. • It allows the horizontal connection of the chimney to the appliance and provides access for inspection and cleaning. • Includes twist-lock Tee Plug.
Supports continued DECORATOR CEILING SUPPORT • Supports up to 50 feet of chimney. • Matte black support gives a finished appearance. Size 6" 8" Dimensions A B 17-7/8" 12-3/8" 19-5/8" 14-3/8" Product Code C 8-1/4" 10-1/4" JSC6DCS JSC8DCS Pack 1 1 CATHEDRAL CEILING SUPPORT BOX • Used in pitched ceiling installations. • Supports up to 38 feet of chimney. • Matte black finish. Size Add JUSI (pg. 11) to the Cathedral Ceiling Support for increased performance and safety.
Shields continued RAFTER RADIATION SHIELD • Must be installed where the chimney is enclosed immediately below the roof line. Size 5" 6" 7" 8" Dimensions A B 9" 12" 10" 12" 11" 12" 12" 12" Product Code Pack JSC5RRS JSC6RRS JSC7RRS JSC8RRS 1 1 1 1 WALL THIMBLE • Used in a wall support installation. • Radiation shield is included with spacers which maintain the mandatory two inch clearance to combustibles. • Attractive matte black finishing trim is included.
Flashings and Storm Collars continued RUBBER BOOT FLASHING KIT THIS KIT INCLUDES: • Special Storm Collar • Rubber Boot • Spacer Kit • Special Boot Mounting Screws • This kit fits 5", 6", 7" and 8" Chimneys • Required where the chimney passes through a corrugated roof. • Rubber Boot Flashing fits roof pitches up to 12/12" (10/12 for 8"). Size Product Code A Pack B ALL JURBFK1 1 STORM COLLAR • Used in conjunction with Roof Flashing to keep precipitation out.
Parts and Accessories WALL BAND • Provides lateral support for the chimney when installed adjacent to a wall. • Maintains the mandatory two inch clearance to combustibles. • Install on 1st length above the Tee, then every 8 feet thereafter.
Parts and Accessories continued UNIVERSAL ROOF GUY KIT • • • • Used when 5 feet or more of chimney extends above the roof. The kit includes two 5 foot rods and an adjustable band. Each rod extends to approximately 10 feet. The adjustable band will fit 5", 6", 7" and 8" diameter chimney.
Typical Installations DECORATOR CEILING SUPPORT INSTALLATIONS One Storey Two Storey Deluxe Rain Cap Chimney Sections Storm Collar Adjustable roof Flashing Deluxe Rain Cap Deluxe Rain Cap Chimney Sections Chimney Sections Storm Collar Storm Collar Adjustable roof Flashing Adjustable roof Flashing Attic Insulation Shield Attic Insulation Shield Decorator Ceiling Support Double Wall Stove Pipe Stove Pipe Adapter Elbow Instalation Stainless Steel Elbow Chimney must be enclosed in living space