Data Sheet

ManualsBrandsSuppo ManualsUAV & Drone ESCs / Speed ControllersSuppo 100A ESC

SUPPO™

™™

™ Speed Controller Programming Instructions

For Advance programmable Normal Aircraft/Boat ESC

50A/60A/70A/ /100A /200A (No BEC)

70A+UBC/100A+UBEC

Important Note:

Some of these ESCs are

No BEC

to your Receiver. For those

No BEC ESC, you need extra power source for your receiver. You can use a UBEC, a

voltage regulator, or extra batteries as the power source for your receiver. If you hear the

music tone repeat again and again for more than 3 times, you may need to check your

power source to the receiver.

··

·Phrases 1 Enter programming Mode

1. Connect your motor and receiver to the speed controller, but do not connect the

battery yet.

2. Turn on your transmitter and move the throttle stick to the full throttle position (full

up). Please Note: Most Futaba transmitters have the throttle channel reversed by

default.

3. Connect your battery and the controller will initialize with a musical tone.

··

·Phrases 2 Programming

After 3 seconds, the controller will start beeping a sequence of tones – a musical tone

followed by one or more beeps. Each sequence represents a parameter that you can program

and is repeated 3 times. The parameters are:

♪

—

Music Tone + 1

Beep

Options 1. Cell Type and No. of Cells

♪

— —

Music Tone + 2

Beeps

Options 2. Throttle Setting

♪

— — —

Music Tone + 3

Beeps

Options 3. Brake Setting

♪

— — — —

Music Tone + 4

Beeps

Options 4. Direction and Cutoff Type

♪

— — — — —

Music Tone + 5

Beeps

Options 5. Timing Mode

♪— — — — — －

Music Tone + 6

Beeps

Option 6. PWM setting

Step 1. Starting, Enter Sub-optins. When you hear the sequence for the parameter you wish to

program, move the throttle stick to the Center Position to Enter Sub-options.

The controller will then start beeping a Morse code sequence of short and long beeps

representing the possible options you may choose for the selected parameter. See table 2 for

a list of all programmable options. Each option sequence is repeated 3 times.

Summary of content (4 pages)

PAGE 1
SUPPO™ ™ Speed Controller Programming Instructions For Advance programmable Normal Aircraft/Boat ESC 50A/60A/70A/ /100A /200A (No BEC) 70A+UBC/100A+UBEC Important Note: Some of these ESCs are No BEC to your Receiver. For those No BEC ESC, you need extra power source for your receiver. You can use a UBEC, a voltage regulator, or extra batteries as the power source for your receiver.
PAGE 2
Step 2. Select and save, the select the option, move the throttle stick back to the Full-up-position., When you hear the sequence for the option you wish to select. The controller will then save the selected option, and sound a long beep as a confirmation. It then goes back to the beginning of the programming sequence (phrases 2). Step 3. Complete programming and exit programming mode. Setup all the parameters you need to change. When complete, move the throttle stick to the Lowest (Down) Position.
PAGE 3
Option 1.5 Cell Type and Number of Cells ♪— Only for100A-SHV-15S / 200A-SHV-15S (SHV-15S LiPo) • — 1 Short + 1 Long NiMh/NiCD Auto Cell Count - 0.8V/Cell Cutoff Voltage * • — — 1 Short + 2 Long 15S Li-Po (45.4V) – 39V Cutoff Voltage • — — — 1 Short + 3 Long 14S Li-Po (41.7V) – 33V Cutoff Voltage • — — — — 1 Short + 4 Long 13S Li-Po (37V) – 30V Cutoff Voltage • — — — — —1 Short + 5 Long 12S Li-Po (33.3V) – 27V Cutoff Voltage • — — — — — — 1 Short + 6 Long 11S Li-Po (29.
PAGE 4
Option 6.