XPass 2 INSTALLATION GUIDE Version 1.00 English EN 101.00.XP2-MDPB V1.
Contents Safety instructions............................................................................................ 3 Introduction ...................................................................................................... 5 Components ...................................................................................................................................................5 Name and function of each part ................................................................................
Safety instructions Safety instructions Observe the following instructions to use the product safely and prevent any risk of injury or property damage. Warning Noncompliance of instructions could lead to serious injury or death. Installation Do not install the product in a place with direct sunlight, moisture, dust, or soot. • A fire or electric shock may occur. Do not install the product in a place with heat from an electric heater. • A fire or electric shock may occur due to overheating.
Safety instructions Operation Do not drop the product or apply an impact to the product. • A product failure may occur. When cleaning the product, wipe the product with a soft and dry cloth and no water, benzene or alcohol. • Otherwise, a product failure may occur.
Introduction Introduction Components XPass 2 Drilling Template Wall Bracket Diode Wall Fixing Screw x 2 Shrink Tube NOTE • Ferrite Core Bracket Fixing Screw (Star Shaped) Quick Guide PVC Anchor x 2 Components may vary according to the installation environment.
Introduction Name and function of each part LED lamp RF card authentication unit Reset button Cable Name Description LED lamp Indicates the operational status of the device with the color of the LED lamp. RF card authentication unit Reads RF cards for entering and exiting. Reset button Initialize the device.
Introduction Cables and connectors Pin Name Color 1 485 TRXP Blue (White stripe) 2 485 TRXN Yellow (Black stripe) 3 485 GND White (Black stripe) 4 ENET RXN Yellow 5 ENET RXP Black 6 ENET TXN Orange 7 ENET TXP White 8 ENET VB1 Red 9 ENET VB1 Green 10 ENET VB2 Blue 11 ENET VB2 Brown 12 WG GND Black 13 WG D1 White 14 WG D0 Green 15 TTL IN0 Purple 16 TTL IN1 Brown 17 TTL GND Gray 18 RLY NO Gray (White stripe) 19 RLY COM Green (White stripe) 20 RLY NC
Installation Installation Fixing the bracket and the product 1 Determine the correct position to install the bracket using the provided drilling template. Fix the bracket firmly using fixing screws through the bracket to the position where XPass 2 will be installed. NOTE • • If installing XPass 2 on a concrete wall, drill holes, insert PVC anchors, and fix them with fixing screws. To avoid RF interference, a minimum separation distance must be maintained.
Installation 2 Install XPass 2 onto the fixed bracket. Wall 3 Assemble XPass 2 with the bracket by rotating the product fixing screw. Wall NOTE • When assembling the product with the bracket, you can use the included bracket fixing screw(Star Shaped) instead of the product fixing screw for enhanced security.
Installation Power supply connection 21 - PWR +VDC 22 - PWR GND Red Black (White stripe) DC power XPass 2 NOTE • • Use a power supply adaptor of DC 12 V (± 10%) with a minimum of 1,000 mA or DC 24V (± 10%) with a minimum of 500 mA which has obtained the approval of IEC/EN 60950-1.
Installation LAN connection (connecting to a PC directly) XPass 2 has an automatic MDI/MDIX function so that it can be connected to a PC directly using a normal straight type CAT-5e cable, not a cross cable.
Installation Relay connection Fail Safe Lock In order to use the Fail Safe Lock, connect N/C relay as shown in the figure below. There is normally a current flowing through the relay for the Fail Safe Lock. When the relay is activated, blocking the current flow, the door will open. If the power supply to the product is cut off due to a power failure or an external factor, the door will open.
Installation Automatic door connection Door button 18 - RLY NO 19 - RLY COM Gray (White stripe) Green (White stripe) Sensor 18 Automatic door Controller 19 Door Lock XPass 2 13
Installation Connecting as a standalone XPass 2 can be connected to the door lock, door button, and door sensor directly without connecting a separate I/O device.
Installation Connecting to Secure I/O 2 Secure I/O 2 is an I/O device, can be connected to XPass 2 with the RS-485 cable. Security can be maintained even if the connection between XPass 2 and Secure I/O 2 has been lost or the power supply to BioEntry W2 has been shut off due to external factors. • Use the RS-485 cable with AWG24, twisted pair, and less than 1.2 km in length. • If connecting with a RS-485 daisy chain, connect the termination resistor (120 Ω) to both ends of the daisy chain connection.
Installation Wiegand connection XPass 2 Use as a Wiegand input/output device 12 - WG GND 13 - WG D1 14 - WG D0 RFID reader / Control device 16 Black White Green
Installation Resetting Network Settings 1 2 3 4 5 Turn the power on. Press and hold the reset button on the rear of device until the device restart automatically. Connect the device with default values. • TCP/IP address: DHCP address assignment (If DHCP address assignment is failed, 169.254.x.x will be set.) • Server mode: Disabled • RS-485: Default, 115200 bps Change the TCP/IP address or RS-485 information. Turn the power off later on and then check the network setting is properly.
Product specifications Product specifications Category Credential General LF card option HF card option NFC card BLE card RF read range * CPU Memory LED Sound Operating temperature Storage temperature Operating humidity Storage humidity Dimension (W x H x D) Weight Capacity Interface IP rating IK rating Certificates Max. User Max. Card Max.
Product specifications Dimensions (Unit: mm) * The tolerance is ±0.3mm. 144.7 48 27 132.2 39.
FCC compliance information FCC compliance information THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
Appendices Appendices Disclaimers • The information in this manual is provided with regard to the Suprema's products. • The right to use is acknowledged only for products included in the terms and conditions of the sales agreement guaranteed by Suprema. The right of license to other intellectual property rights not discussed in this manual is not acknowledged.
Appendices When we speak of free software, we are referring to freedom, not price. Our General Public Licenses are designed to make sure that you have the freedom to distribute copies of free software (and charge for them if you wish), that you receive source code or can get it if you want it, that you can change the software or use pieces of it in new free programs, and that you know you can do these things.
Appendices case of interfaces specified for a particular programming language, one that is widely used among developers working in that language.
Appendices • regardless of how they are packaged. This License gives no permission to license the work in any other way, but it does not invalidate such permission if you have separately received it. d) If the work has interactive user interfaces, each must display Appropriate Legal Notices; however, if the Program has interactive interfaces that do not display Appropriate Legal Notices, your work need not make them do so.
Appendices 7. Additional Terms. “Additional permissions” are terms that supplement the terms of this License by making exceptions from one or more of its conditions. Additional permissions that are applicable to the entire Program shall be treated as though they were included in this License, to the extent that they are valid under applicable law.
Appendices organization, or merging organizations. If propagation of a covered work results from an entity transaction, each party to that transaction who receives a copy of the work also receives whatever licenses to the work the party's predecessor in interest had or could give under the previous paragraph, plus a right to possession of the Corresponding Source of the work from the predecessor in interest, if the predecessor has it or can get it with reasonable efforts.
Appendices The Free Software Foundation may publish revised and/or new versions of the GNU General Public License from time to time. Such new versions will be similar in spirit to the present version, but may differ in detail to address new problems or concerns. Each version is given a distinguishing version number.
Appendices 1. Exception to Section 3 of the GNU GPL. You may convey a covered work under sections 3 and 4 of this License without being bound by section 3 of the GNU GPL. 2. Conveying Modified Versions.
Appendices version for the Library. OpenSSL License Copyright (c) 1998-2017 The OpenSSL Project. All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. 2.
Appendices LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. The licence and distribution terms for any publically available version or derivative of this code cannot be changed. i.e. this code cannot simply be copied and put under another distribution licence [including the GNU Public Licence.
Suprema Inc. 17F Parkview Tower, 248, Jeongjail-ro, Bundang- gu, Seongnam-si, Gyeonggi-do, 13554, Rep. of KOREA Tel: +82 31 783 4502 I Fax: +82 31 783 4503 I Inquiry: sales_sys@supremainc.com ©2019 Suprema Inc. Suprema and identifying product names and numbers herein are registered trade marks of Suprema, Inc. All non-Suprema brands and product names are trademarks or registered trademarks of their respective companies.
