Owner manual

ManualsBrandsSure Heat ManualsHardware2008 Four Seasons FSIS Natural Gas Conversion Kit

NATURAL GAS CONVERSION MANUAL

For Model FSISLP

FOR OUTDOOR USE ONLY

Part No. Qty Description

1 RCOZZ00341A 1 Main Burner Valve & Manifold Assembly with Valves (NG)

2 RPAZZ00002A 1 Thread Sealing Tape

3 RCOZZ00341A 1 Side Burner Orice (NG)

4 RCOZZ00117A 1 NG Regulator 3/8” NPT x 3/8” UNF

5 RCODZ00026A 2 Orice Back IR (NG)

6 RCODZ00052A 1 Connecting tube 3/8" NPT

Summary of content (8 pages)

PAGE 1
NATURAL GAS CONVERSION MANUAL For Model FSISLP FOR OUTDOOR USE ONLY 1 4 1 2 3 4 5 6 Part No.
PAGE 2
FSISLP Natural Gas Conversion Instructions Tools needed: Phillips head screwdriver 3/4” wrench 1/4” wrench or socket Adjustable wrench ! WARNING ▲ Be sure gas supply is off, the knobs are in the off position and the grill is cool. ! Wear golves to be protected from the sharp edges of the interior parts. ▲ NOTE: Make sure to use supplied pipe sealant on all non-flared fittings. 1. To get started, remove all the control knobs and set aside. (See Fig. 1) Fig. 1 2.
PAGE 3
FSISLP Natural Gas Conversion Instructions 5. Remove the two (2) phillips pan head screws from the right side of the control panel. (See Fig. 5) Fig. 5 Phillips Pan Head Screws 6. Let a friend help you to carefully pull the front control panel away from the grill a little and hold it. (See Fig. 6) 7. Use a wrench hold the elbow on the rear IR burner valve and use another wrench to disconnect the flex line. (See Fig. 7) Fig. 6 Fig. 7 flex line elbow Fig. 8 8.
PAGE 4
FSISLP Natural Gas Conversion Instructions 10. Remove the front control panel, use a screw driver to remove the twelve (12) screws securing the bezels and the manifold in position. (See Fig. 10) Fig. 10 11. Replace the LP manifold with the one provided in the NG conversion kit. Use the twelve screws removed in step 10 to attach the bezels and manifold onto the front control panel. (See Fig. 10 -11) NOTE: Make sure the “ OFF” position facing up as it was.
PAGE 5
FSISLP Natural Gas Conversion Instructions 15. Place the front control panel back onto the grill and hold it. Feed the two igniter wires through the hole on the grill head bottom into the grill cabinet. Reconnect the wires to the two outstand terminal tabs on the igniter module. (See Fig. 15) Fig. 15 16. Reattach the flex lines to the rear IR burner valve, bottom IR burner valve and side burner valve. (See Fig. 16) Note: Be careful, applying pressure to the elbow of the valves may cause them to break.
PAGE 6
FSISLP Natural Gas Conversion Instructions Fig. 20 20. Remove the two (2) screws securing the bottom IR burner in position on the front. (See Fig. 20) 21. Remove the rear one screw securing the bottom IR burner in position. (See Fig. 21) Fig. 21 Fig. 22 22. Pull the bottom IR burner out a little and disconnect the flex line and igniter wire . (See Fig. 22) Note: Make sure the igniter wire dose not fall into the grill. 23.
PAGE 7
FSISLP Natural Gas Conversion Instructions 25. Use the three (3) screws removed in step 20-21 to secure the bottom IR burner in position. (See Fig. 25) 26. Remove the six screws securing the wind shield and rear IR cover in position. (See Fig. 26) 27. Grasp the rear IR cover and remove it. (See Fig. 27) Fig. 25 Fig. 26 Fig. 27 Fig. 28 28. Hold the elbow and use a wrench to remove the rear IR burner LP orifice. (See Fig. 28) 29.
PAGE 8
FSISLP Natural Gas Conversion Instructions 30. Attach the 3/8" NPT connecting tube onto the manifold. (See Fig. 30) Fig. 30 NOTE: Make sure to use supplied pipe sealant on all non-flared fittings. 31. Attach the NG regulator onto the connecting tube. (See Fig. 31) Note: pay attention to arrow on the NG regulator indicating direction of gas flow. The arrow should point toward the grill. Fig. 31 NOTE: Make sure to use supplied pipe sealant on all non-flared fittings. 32.