Owner manual

ManualsBrandsSure Heat ManualsHardwareSonoma SGIR27 Natural Gas Conversion Kit

PLA

TINUM

EDITION

27" Rear Infrared Model

Natural Gas Conversion Manual

Part No. Qty Description

44213827 1 Hose 27" - 3/8" Flare Both Ends for Side Burner (NG)

40276201

Main Burner

Valve & Manifold Assembly with Valves (NG)

3 44110102 2 Connector 3/8" MNPT x 3/8" Flare

4 44133801 1 Tee Fitting - Galvanized 3/8" Flare

5 49900004 1 Sealant Pipe (4ml)

6 44183815 1 Nipple Pipe 3/8" NPT x 1.5"

7 47311010 1 Regulator 3/8" FNPT Threads (NG)

8 46210102 1 Side Burner Valve Assembly - 12K BTU (NG)

9 08338381 1 3/8" Street Elbow

10 08005201 1 Rear IR NG Orifice

CANADIAN GAS ASSOCIATION

APPROVED

NOTE: Images in this manual may differ slightly from your grill

FOR OUTDOOR USE ONLY

Summary of content (8 pages)

PAGE 1
Sonoma 27" Rear Infrared Model Natural Gas Conversion Manual P L AT I N U M EDITION TM FOR OUTDOOR USE ONLY 1 2 3 4 10 7 8 5 6 9 Part No. Qty Description 1 44213827 1 Hose 27" - 3/8" Flare Both Ends for Side Burner (NG) 2 40276201 1 Main Burner Valve & Manifold Assembly with Valves (NG) 3 44110102 2 Connector 3/8" MNPT x 3/8" Flare 4 44133801 1 Tee Fitting - Galvanized 3/8" Flare 5 49900004 1 Sealant Pipe (4ml) 6 44183815 1 Nipple Pipe 3/8" NPT x 1.
PAGE 2
SGIR27 Natural Gas Conversion Instructions Tools Needed: Phillips head screwdriver 1/4” nut driver * Channel locks Adjustable wrench Rear Heat Shield Fig 2 Screws * 1/4” socket set with extension can also be used. Be sure gas supply is off, the knobs are in the off position and the grill is cool. Fig 3 1. Remove cooking grates and flavor grids. (See Fig. 1) Screws Igniter Heat Shield 2. Remove the screws holding the rear heat shield in place. Lift out rear heat shield and set aside. (See Fig. 2) 3.
PAGE 3
SGIR27 Natural Gas Conversion Instructions 7. Remove the front heat shield. (See Fig. 7) 8. Grasp and push the burner(s) towards the rear of the grill to detach the burner from the valves. (See Fig. 8) Fig 9 9. Angle the burners up and remove. (See Fig. 8) 10. Remove the control knobs from the front of the grill. (See Fig. 9) Screws 11. Remove the two (2) screws holding each bezel in place on the control panel. (See Fig. 10) Fig 10 12. Remove the bezels from the front control panel.
PAGE 4
SGIR27 Natural Gas Conversion Instructions 14. Remove manifold from grill body. (See Fig. 14) Manifold You are now ready to install the new NG manifold. Fig 14 15. Start by placing the new manifold into the grill body with the control knob stems going outward through control panel front. (See Fig. 15) 16. Reattach the flex line on the right of the grill to the new manifold using the adjustable wrench. (See Fig. 12 on previous page) Control Knob Stems 17.
PAGE 5
SGIR27 Natural Gas Conversion Instructions Installing the NG regulator Main Gas Pipe 1. Remove the LP regulator from the main gas pipe using an adjustable wrench. Located inside the cart on bottom of grill head. (See Fig. 19) Fig 20 Remaining end still connected will be removed later. LP Nipple 2. Remove the LP nipple brass fitting from main gas pipe. (See Fig. 20) Note: For the following steps, the supplied pipe dope needs to be applied to all indicated fittings before the fittings are screwed in.
PAGE 6
SGIR27 Natural Gas Conversion Instructions 7. Attach the 3/8" nipple to the 3/8" street elbow. (See Fig. 25) 8. Attach the NG regulator to the nipple (See Fig. 26). Fig 26 Note: pay attention to arrow on the NG regulator indicating direction of gas flow. The arrow should point toward the grill. Remember to apply pipe dope! 9. Attach one end of the supplied hose to the flared fitting on the side of the “T” connector. (See Fig.
PAGE 7
SGIR27 Natural Gas Conversion Instructions 4. Remove the two (2) screws holding the bezel and valve in place. Remove bezel from the front of the side burner. (See Fig. 11 on page 3) Casting Side Burner Assy Fig 32 5. Remove the two (2) screws holding the side burner LP valve assembly in place. This will free up the assembly. (See Fig. 31) 6. Holding the assembly securely, remove side burner assembly from casting. Replace with new side NG side burner assembly. (See Figs.
PAGE 8
SGIR27 Natural Gas Conversion Instructions Converting the Rear Infrared Burner to NG 1. Remove the four (4) screws on the inside of the grill that hold the rear infrared cover in place. (See Fig. 37) Fig 37 Rear Screws 2. Close the grill hood slowly, 3. Remove the two (2) screws from the back infrared cover, located on the back of the grill. (See Fig. 38) Fig 38 4. Grasp rear infrared cover and remove it from the grill. (See Fig. 38) 5. Disconnect flex line and twist orifice elbow to remove LP orifice.