Owner's manual

ManualsBrandsSure Heat ManualsHardwareTuscany CS812 Natural Gas Conversion Kit

CS812 Natural Gas Conversion Manual

FOR OUTDOOR USE ONLY

Part No. Qty Description

1 RCOZZ00345A 1 Main Burner Valve & Manifold Assembly with Valves (NG)

2 RCOZZ00117A 1 Hose 27" - 3/8" Flare Both Ends for Side Burner (NG)

3 RPAZZ00002A 1 Thread Sealing Tape

4 RCOZZ00346A 1 Side Burner Orifice (NG)

5 RCOZZ00117A 1 NG Regulator 3/8” NPT x 3/8” UNF

6 RCODZ00026A 1 Orifice Back IR NG"

7 RCOZA00021A 1 Tee Fitting - Galvanized 3/8" NPT

8 RCODZ00024A 1 Connector 3/8” NPT x 3/8” UNF

NOTE: Images in this manual may differ slightly from your grill.

Tuscany

bbyy AAllttiimmaa

Summary of content (6 pages)

PAGE 1
Tuscany TM by Altima CS812 Natural Gas Conversion Manual FOR OUTDOOR USE ONLY 4 3 6 1 7 5 8 2 1 2 3 4 5 6 7 8 Part No.
PAGE 2
CS812 Natural Gas Conversion Instructions Tools Needed: Phillips head screwdriver 3/4” wrench 1/4” wrench or socket Adjustable wrench Fig 1 * 1/4” socket set with extension can also be used. Side burner valve elbow Side burner valve hose Be sure gas supply is off, the knobs are in the off position and the grill is cool. Wear a golve to be protected from the sharp edges of the interior parts To get started, remove all the control knobs and set aside.
PAGE 3
CS812 Natural Gas Conversion Instructions 6. Remove the four (4) phillips pan head screws at both sides of the the front control panel. (See Fig. 6) Phillps pan head screws 7. Let a friend help you to pull the front control panel away from the grill and hold it. Using a wrench, hold the elbow on the rear IR burner valve and use another wrench to disconnect the flex line. (See Fig. 7) 8.
PAGE 4
CS812 Natural Gas Conversion Instructions 13. Push the front control panel back in position, make sure the orifices of the valves insert into the main burner tubes. Then use the four (4) screws remvoed in step 6 on page 3 to secure the front control panel in position. (See Fig. 11) Main burner tube Fig 11 14. Remove the six (6) screws securing the rear IR cover and wind shield in position. (See Fig. 12) Control valve orifice 15.
PAGE 5
CS812 Natural Gas Conversion Instructions 19. Unscrew the nut securing the bracket on the side burner orifice. (See Fig. 16) 20. Use a wrench to remove the side burner orifice from the flex line and replace it with the NG orifice provided in the kit. (See Fig. 17) 21. Use the nut removed in step 19 to secure the bracket onto the side burner orifice. (See Fig. 16) Fig 16 Bracket 22. Use the two screws removed in step 18 on page 4 to secure the bracket in position. (See Fig. 15 on page 4) 23.
PAGE 6
CS812 Natural Gas Conversion Instructions Note: Make Sure to use thread Sealing tape on all non-flared fittings. 27. Attach the tee fitting to the manifold as shown. Tighten with wrench. (See Fig. 18) Fig 18 28 .Attach the Connector 3/8” NPT x 3/8” UNF to the tee fitting as shown. Tighten with wrench. (See Fig. 19) 29. Attach the NG regulator to the tee fitting.(See Fig. 20) Note: pay attention to arrow on the NG regulator indicating direction of gas flow. The arrow should point toward the grill.