Use and Care Manual

SURE STEP
®
ANTI-SLIP COATING 100% ACRYLIC LATEX
FLOOR AND CONCRETE PAINT SU-SERIES
Features
General Description
• Skid Resistant
• Exceptional Color
Retention
• Abrasion Resistant
• Resistant to Ponding Water
• Fills and Seals Cracks
• Fast Drying
Sure Step
®
Anti-Slip Coating provides a durable skid resistant finish
for interior or exterior application. Imparts excellent color retention,
abrasion resistance and resistance to ponding water. Sure Step
®
is
water reduced which allows for fast dry plus easy application and
clean up. Available in 5 ready mixed colors and white. There is also
a clear coat available in this line that can be used as a stand alone
clear finish. Sure Step
®
can be exposed to light foot traffic 24 hours
after application of the final coat. Allow 4-5 days for heavier or
continuous foot traffic. Sure Step
®
Anti-Slip Coating has a Coefficient
of Friction rating of > 1.12. ADA (Americans with Disabilities Act)
guidelines recommend a CF of 0.6 or greater for level surfaces and
0.8 or greater for ramps.
Recommended For
Limitations
Walking surfaces such as tennis courts, patios, walkways,
steps, pool decks and areas subjected to foot traffic.
•
Apply by roller, squeegee or brush (small areas) when surface
temperature is between 55°F (12.8°C) and 90°F (32.2°C).
• On exterior applications, do not apply when rain is threatening.
• Not for immersion service.
• Do not use on garage floors or other surfaces that will be driven on.
• Clear should be used for sealing purposes only. It is not an Anti-Slip
Coating.
Product Information
Colors — Standard:
SU-0001, Clear; Not a non-slip
product
SU-0110, Tintable White
SU-0308, Gray Pearl
SU-0310, Light Gray
SU-0505, Tile Red
SU-0789, Pine Green
SU-0922, Desert Sand
SU-0998, Saddle Brown
Technical Data◊
Tintable
White
Vehicle Type
Acrylic Copolymer
Pigment Type
Titanium Dioxide
Volume Solids
38 ±
1.0%
Coverage per Gallon at
Recommended Film Thickness
80 – 120
Sq. Ft.
Depending on surface texture and porosity. Be sure to
estimate the right amount of paint for the job. This will ensure
color uniformity and minimize the disposal of excess paint.
Dry Time @ 77°
F
(25°
C) @ 50% RH
– Tack Free 1 –
2 Hours
– To Recoat 8
Hours
– Light Service
24 Hours
– Full Cure
4 -5 Days
High humidity and cool temperatures will result in longer dry,
recoat and service times.
Dries By
Evaporation
Viscosity
110 –
115 KU
Flash Point
200°F or greater
(TT-P-
141, Method 4293)
Gloss / Sheen
Flat 5-10 @60
°
Surface Temperature at
Application
– Min. 55°
F
– Max.
90°F
Thin With
Do Not Thin
Clean Up Thinner
Warm,
Soapy Water
Weight Per Gallon
11.6
lbs.
Storage Temperature
– Min.
45°F
– Max.
95°F
Volatile Organic Compounds (VOC)
— Tint Bases:
SU-0110, Tintable White
SU-0002, Accent Base
Can be tinted with Universal colorants.
— Special Colors:
Contact your dealer.
Certification:
The product supported by this data sheet contains a maximum of 250 grams
per liter VOC / VOS (2.09 lbs/gal.) excluding water & exempt solvents.
This product is compliant under the Ozone Transport Commission
regulations as a Floor Coating.
Technical Assistance:
Available through your local authorized independent Insl-x dealer. For the
location of the dealer nearest you, call 1-800-225-5554 or visit
www.insl-
x.com
◊ Reported values are for Tintable White. Contact dealer for values
of other bases or colors.
Manufactured by Benjamin Moore & Co. 101 Paragon Drive, Montvale, NJ 07645 Tel: [phone] Fax: [phone] www.Insl-x.com M72 SU-0XXX EN 011615