Fusion4Home Max Cellular signal booster kit for the Home or Office User Guide 05.17.
Thank you for purchasing SureCall’s Fusion4Home cellular signal booster kit. SureCall’s Fusion4Home Max was specifically designed to eliminate frustrations over dropped calls and limited range by amplifying incoming and outgoing cellular signals in homes and offices. If you have any questions during setup, please reach out to our US-based experienced support technicians: Call: 1-888-365-6283 Email: support@surecall.com Visit: www.surecall.
TABLE OF CONTENTS How it works ...................................................................................................................................... 4 PACKAGE CONTENTS......................................................................................................................... 4 BEFORE INSTALLATION...................................................................................................................... 6 Installation Overview...........................................
How it works 1. The high-gain outside antenna captures even the weakest cell signal, from the cell tower where it is aimed. 2. The Fusion4Home Max Donor booster uses Extended Range Technology™ (ERT) to grab signal outside, at its strongest point , where it boosts voice, text and data signals for all 4G & 5G devices. 3. Using low-loss RG-6 cable, signal is transmitted from the outside to the inside Fusion4Home Max inside host amplifier. 4.
Your Fusion4Home Max signal booster package includes the following items: • SureCall Fusion4Home Max inside host and power supply • Directional Panel Inside Antenna • Inside cable (connects inside Panel to the booster) • Outside Yagi antenna • Outside Amplifier • Outside Cable (connects outside amplifier to inside host) Inside Components 1. Fusion4Home Max inside host amplifier and power supply 2. Panel antenna 3. Inside Cable (20 ft.) Outside Components 4.
BEFORE INSTALLATION Prior to securing the location of any booster parts, a “soft install” is recommended as adjustments may be needed to optimize performance. Ensure adequate separation between the planned locations of the inside and outside antenna – at least 25 ft (see diagram ”Antenna Separation” on page 7).
negatives and generally should fall between -40 and -130. A score closer to zero indicates a stronger signal. For example, a signal of -120 dB indicates no service, while a score of about -50 dB means you have excellent signal. For specific dB signal measurements, use the methods below. • • iOS - First turn off your Wi-Fi, Next, open the Phone app an dial *3001#12345#* then press the call button. This will open the Field Test app.
Once you have identified your install location, assemble the u-bolt, bracket, nuts and washers onto a pole (available separately) as shown in the illustration. Keep the connections loose enough to allow the antenna to rotate until the optimum direction is found. Next assemble the outside amplifier to provided bracket as shown below and secure to in the same location. Connect the Yagi antenna cable connector to the outside amplifier.
Step 3. Install the Inside Amp and Inside Antenna. Choose a location for the booster and inside antenna that is near a working outlet and at least 25 Ft from the outside antenna. Consider the below factors affecting booster performance. 1. Signal strength at the location of the outside antenna. 2. Interior building materials between the inside antenna and your mobile device. 3. Distance between the outside antenna and inside antenna (minimum 25 ft.
Place the Inside Host To install the booster to a wall, select a location that is near a working AC outlet. Use the supplied screws or appropriate screws for surface of mounting location and drill through screw tab holes on booster (see “Booster Diagram” illustration) and mount the booster to a wall. Next, connect the outside and inside components by routing the outside cable from the outside amplifier indoors and connect to the booster port marked “OUTSIDE”.
Step 5: Configure Gain Settings If Needed Place a call in the room where the inside antenna is located to confirm that your phone is receiving a boosted signal. Note: Bars are not always a reliable measure of signal. The best way to confirm signal coverage is the ability to place and hold a call. Only the presence of a RED/YELLOW flash indicates the presence of an unresolved issue.
LED INDICATORS Note: Bars are not always a reliable measure of signal. The best way to confirm signal coverage is the ability to place and hold a call. Only the presence of a RED/YELLOW flash indicates the presence of an unresolved issue. Important: The booster gain dials should remain at maximum level and only reduced if other recommended actions do not resolve the issue. LED Condition Status/Resolution Initializing on Power-up All control lights flash RED & YELLOW for 5 seconds then off for 5 minutes.
SPECIFICATIONS Model Fusion4Home Max (US), Fusion4Home Max CA (Canada) Uplink Frequency Range (MHz): 698-716 / 776 – 787 / 824-849 / 1850-1915 / 1710-1755 Downlink Frequency Range (MHz): 728-746 / 746 – 757 / 869-894 / 1930-1995 / 2110-2155 Maximum Gain: 72 dB Supported Standards: CDMA, WCDMA, GSM, EDGE, HSPA+, EVDO, LTE and all cellular standards Max Uplink Power: 26.0 dBm Input Impedance: 50Ω VSWR ≤2.
Configuration 1: Warning: Any product modifications that use unauthorized antennas, cables, and/or coupling devices are prohibited by the FCC. Contact FCC for details: 1-888-CALL-FCC. Changes or modifications not expressly approved by SureCall could void the user’s authority to operate the equipment. Note: The term “IC” before the radio certification number only signifies that Industry Canada technical specifications were met. FCC 27.
FCC 15.105 Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
CONSUMER GUIDELINES This is a CONSUMER device BEFORE USE, you MUST REGISTER THIS DEVICE with your wireless provider and have your provider’s consent. Most wireless providers consent to the use of signal boosters. Some providers may not consent to the use of this device on their network. If you are unsure, contact your provider. In Canada, BEFORE USE you must meet all requirements set out in ISED CPC-2-1-051 You MUST operate this device with approved antennas and cables as specified by the manufacturer.
WARRANT Y Three-Year Product Warranty To activate your three-year manufacturer’s warranty, register at www.SureCall.com/activate SureCall warrants its products for three years from the date of purchase against defects in workmanship and/or materials. Specifications are subject to change. The threeyear warranty only applies to products meeting the latest FCC Certification Guidelines stated on 2/20/2013 and going into effect April 30, 2014.
SureCall, Inc 48346 Milmont Drive Fremont, California 94538, USA 888.365.6283 | www.surecall.
