This owner’s manual applies to the SX4 series: SX4 SX4 SEDAN 80J2059 NOTE: The illustrated models are examples of the SX4 series. © 2009 All rights reserved. No part of this document may be reproduced or transmitted in any form or by any means, electronic or mechanical, for any purpose, without the express written permission of Suzuki Motor Corporation.
FOREWORD All information in this manual is based on the latest product information available at the time of publication. Due to improvements or other changes, there may be discrepancies between information in this manual and your vehicle. SUZUKI MOTOR CORPORATION reserves the right to make production changes at any time, without notice and without incurring any obligation to make the same or similar changes to vehicles previously built or sold.
IMPORTANT MODIFICATION WARNING WARNING/CAUTION/NOTE Please read this manual and follow its instructions carefully. To emphasize special information, the symbol and the words WARNING, CAUTION and NOTE have special meanings. Pay special attention to the messages highlighted by these signal words: WARNING Do not modify this vehicle. Modification could adversely affect safety, handling, performance or durability and may violate governmental regulations.
LEAK DETECTION PUMP NOTE: Your vehicle has a pump to regularly check the vehicle’s evaporative emission control system for leaks. This check is performed approximately five hours after the engine is turned off. During this leak check, you may hear a sound coming from the vehicle for several minutes. This sound is normal and does not indicate a malfunction.
MEMO 80J23-03E
INTRODUCTION Thank you for choosing SUZUKI and welcome to our growing family. Your choice was a wise one; SUZUKI products are a great value that will give you years of driving pleasure. This Owner’s Manual was prepared to help you have a safe, enjoyable, and trouble-free experience with your SUZUKI. In it you will learn about the vehicle’s operation, its safety features and maintenance requirements. Please read it carefully before operating your vehicle.
SERVICE STATION GUIDE 1. 2. 3. 4. 5. 6. 7. 8. 9. 10.
TABLE OF CONTENTS California Proposition 65 Warning WARNING Engine exhaust, some of its constituents, and certain product components contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
ILLUSTRATED TABLE OF CONTENTS EXTERIOR 1. Rear Window Wiper (if equipped) (P.2-80) 2. High-mount Stop Light (if equipped) (P.7-45) 3. Radio Antenna (P.5-15) 4. Engine Hood (P.5-44) 5. Head Light (P2-75, P7-41) 6. Windshield Wiper (P.2-78) 7. Roof Rail (if equipped) (P.5-55) 8. Fuel Filler Cap (P.5-43) 9. License Plate Light (P.7-44) 10. Tailgate (if equipped) (P.2-3) 11. Rear Combination Light (P.7-43) 12. Front Fog Light (if equipped) (P.2-77, 7-42) 13. Outside Rearview Mirror (P.2-20) 14. Door Locks (P.
ILLUSTRATED TABLE OF CONTENTS INTERIOR 1. Seat Belts (P.2-28) 2. Side Curtain Air Bags (if equipped) (P.2-50) 3. Interior Light (P.5-45, 7-40) 4. Assist Grip (if equipped) (P.5-48) 5. Power Mirror Control Switch (if equipped) (P.2-20)/ Power Window Controls (P.2-17) 6. Sun Visor (P.5-45) 7. Spot Light (P.5-47, 7-40) 8. Inside Rearview Mirror (P.2-19) 9. Luggage Compartment Light (if equipped) (P.5-46, 7-45) 10. Luggage Compartment Cover (if equipped) (P.5-52) 11. Rear Seat (P.2-24) 12.
ILLUSTRATED TABLE OF CONTENTS INSTRUMENT PANEL 1. Lighting Control Lever (P.2-75)/ Turn Signal Control Lever (P.2-77) 2. Shift Paddles (if equipped) (P.3-14) 3. Front Air Bags (P.2-49) 4. Instrument Cluster (P.2-59) 5. Windshield Wiper and Washer Lever (P.2-78)/Rear Window Wiper and Washer Switch (if equipped) (P.2-80) 6. Hazard Warning Switch (P.2-78) 7. Audio (P.5-15) 8. Front Fog Light Switch (if equipped) (P.2-77) 9. Fuse Box (P.7-36) 10. Engine Hood Release Handle (P.5-44) 11.
ILLUSTRATED TABLE OF CONTENTS TIRE CHANGING TOOL 1. 2. 3. 4. Jack Handle (P.8-1) Wheel Brace (P.8-1) Spare Tire (P.7-31, 8-1) Jack (P.
LOCATION OF WARNING MESSAGES 11 12 Read and follow all of the warnings (labels etc.) on your vehicle. Make sure you understand all of them. Keep them on the vehicle. Do not remove the messages for any reason. If a label comes off or the messages become difficult to be read, have it corrected by your SUZUKI dealer. 1 9 Driver 1. Air bag warning labels (on both sun visors) 2. Jacking warning label 3. Fuel filler cap message 4. Brake fluid cap message 5. Engine cooling fan warning label 6.
FUEL RECOMMENDATION FUEL RECOMMENDATION 1 Fuel Recommendation ........................................................
Fuel Recommendation: 1, 2 FUEL RECOMMENDATION Fuel Recommendation Gasoline Containing MTBE Fuel Pump Labeling Unleaded gasoline containing MTBE (methyl tertiary butyl ether) may be used in your vehicle if the MTBE content is not greater than 15%. This oxygenated fuel does not contain alcohol. In some states, pumps that dispense oxygenated fuels are required to be labeled for the type and percentage of oxygenate and whether important additives are present.
BEFORE DRIVING BEFORE DRIVING 60G404 Keys ...................................................................................... 2-1 Door Locks .......................................................................... 2-1 2 Keyless Start System Remote Controller/ Keyless Entry System Transmitter .................................... 2-6 Theft Deterrent Light ........................................................... 2-17 Windows ...........................................................................
Keys: 8 Door Locks: 3, 5, 8 BEFORE DRIVING Keys Door Locks To unlock a front door from outside the vehicle, insert the key and turn the top of the key toward the front of the vehicle. WARNING EXAMPLE Always lock all doors when driving. Locking the doors helps to prevent occupants from being thrown from the vehicle in the event of an accident. It also helps prevent unintended opening of the doors.
Door Locks: 3, 5, 8 BEFORE DRIVING Power Door Locking System You can lock and unlock all the doors (including the tailgate of SX4) simultaneously by: • Turning the key in a front door lock, or • Pushing the power door locking switch located on the driver’s side or the front passenger’s side door panel. Front passenger’s side EXAMPLE To unlock only one of the front doors, insert the key in that door lock and turn the top of the key toward the front of the vehicle once.
Door Locks: 3, 5, 8 BEFORE DRIVING NOTE: • If your vehicle is equipped with the keyless entry system, you can also lock or unlock all doors by operating the remote controller/transmitter. Refer to “Keyless Start System Remote Controller/Keyless Entry System Transmitter” in this section. • If your vehicle is equipped with the keyless start system, you can also lock or unlock all doors by pushing the request switch on the door handle.
Door Locks: 3, 5, 8 BEFORE DRIVING Trunk Lid (SX4 SEDAN) WARNING Always make sure that the tailgate is closed and latched securely. Completely closing the tailgate helps prevent occupants from being thrown from the vehicle in the event of an accident. Completely closing it also helps keep exhaust gases from entering the car.
Door Locks: 3, 5, 8 BEFORE DRIVING Internal Trunk Release (SX4 SEDAN) EXAMPLE (1) EXAMPLE 56KN010 80JC005 If your vehicle is equipped with a trunk lid unlatch switch (1), push and hold the trunk lid unlatch switch (1) and lift the trunk lid to open the trunk lid. You can unlock the lid by pulling the release lever located to the outboard side of the driver’s seat. WARNING The trunk lid unlatch switch (1) operates when the keyless start system remote controller is within the switch’s operating range.
Door Locks: 3, 5, 8 BEFORE DRIVING Keyless Start System Remote Controller/Keyless Entry System Transmitter Type A Type B Keyless Start System Remote Controller (Type A) The remote controller enables the following operations: • You can lock or unlock the doors by operating the LOCK/UNLOCK buttons on the remote controller. Refer to the explanation in this section. • You can lock or unlock the doors by pushing the request switch on the door handle. For details, refer to the explanation in this section.
Door Locks: 3, 5, 8 BEFORE DRIVING NOTE: • The maximum operating distance of the remote controller is about 5 m (16 ft.), but this can vary depending on the surroundings, especially near other transmitting devices such as radio towers or CB (Citizen’s Band) radios. • The door locks cannot be operated with the remote controller if the ignition switch is in a position other than “LOCK”, or the ignition key is inserted in the ignition switch, or if any door is open.
Windows: 3, 8 BEFORE DRIVING When the remote controller is within the operating range described in this section, you can lock or unlock the doors by pushing the request switch (1) on the door handle of the driver’s door, front passenger’s door or tailgate of SX4. To lock all doors when all doors are unlocked: • Push the request switch on one of the door handles once. The turn signal lights will flash once when the doors are locked.
Windows: 3, 8 BEFORE DRIVING CAUTION The remote controller is a sensitive electronic instrument. To avoid damaging the remote controller: • Do not expose it to impacts, moisture or high temperature such as by leaving it on the dashboard under direct sunlight. • Keep the remote controller away from magnetic objects such as a television.
Windows: 3, 8 Mirrors: 3, 8 BEFORE DRIVING • If you open the driver’s door and lock the door by turning the lock knob forward or pushing the power door locking switch, the driver’s door will be automatically unlocked. • If you open a door other than the driver’s door and lock the front passenger’s door by turning the lock knob forward or pushing the power door locking switch, the front passenger’s door will be automatically unlocked.
Mirrors: 3, 8 Seat Adjustment: 3 BEFORE DRIVING WARNING Swallowing a lithium battery may cause serious internal injury. Do not allow anyone to swallow a lithium battery. Keep lithium batteries away from children and pets. If swallowed, contact a physician immediately. (1) CAUTION 80J2076 (1) Lithium disc type battery: CR2032 or equivalent 2) Replace the battery (1) so its + terminal faces the bottom of the case as shown in the illustration. 3) Close the remote controller firmly.
Seat Adjustment: 3 BEFORE DRIVING To program a new remote controller 1) Close all the doors of the vehicle. 2) Sit in the driver’s seat and confirm that the driver’s door is unlocked. 3) Insert the key into the ignition switch. 4) Complete steps 1 through 6 described below within 25 seconds after step 3). UNLOCK (2) LOCK (1) 80JC093 1. Push the power door locking switch of the driver’s door to the lock position and then push it to the unlock (2) position. 2. Repeat step 1 two more times. 3.
Seat Adjustment: 3 Head Restraints: 3 BEFORE DRIVING To change the old remote controller codes in your vehicle’s memory If you have lost one of the remote controllers, you should change the remote controller codes in your vehicle’s memory as soon as possible for security. To erase the remote controller code(s) in your vehicle’s memory, you should program the new remote controller code. The old codes in your vehicle’s memory will be erased automatically.
Head Restraints: 3 Seat Belts and Child Restraint Systems: 3 BEFORE DRIVING The turn signal lights will flash once when the doors are locked. When the doors are unlocked: • The turn signal lights will flash twice. • If the interior light switch is in the “DOOR” position, the interior light will turn on for about 15 seconds and then fade out. If you insert the key into the ignition switch during this time, the light will start to fade out immediately.
Seat Belts and Child Restraint Systems: 3 BEFORE DRIVING CAUTION The transmitter/remote controller is a sensitive electronic instrument. To avoid damaging it, do not expose it to dust or moisture or tamper with internal parts. (1) Programming/removing a transmitter code yourself Your new vehicle was originally equipped with two transmitters. 80J2077 (1) Lithium disc type battery: CR2025 or equivalent 2) Replace the battery (1) so its + terminal faces the “+” mark of the transmitter.
Seat Belts and Child Restraint Systems: 3 BEFORE DRIVING To change the old transmitter codes in your vehicle’s memory If you have lost one of the transmitters, you should change the transmitter codes in your vehicle’s memory as soon as possible for security.
Seat Belts and Child Restraint Systems: 3 BEFORE DRIVING Theft Deterrent Light Windows Passenger’s door EXAMPLE Power Window Controls (3) Driver’s side EXAMPLE (1) (4) (2) 80JM022 This light will blink with the ignition switch in the “OFF” or “ACC” position. The blinking light is intended to deter theft by leading others to believe that the vehicle is equipped with a security system. 80JC096 (5) The passenger’s door has a switch (3) to operate the passenger’s window.
Seat Belts and Child Restraint Systems: 3 BEFORE DRIVING Lock switch WARNING EXAMPLE CLOSE OPEN 81A009 To open a window, push the top part of the switch and to close a window lift up the top part of the switch. The driver’s window has an auto-down feature for added convenience (at toll booths or drive-through restaurants, for example). This means you can open the window without holding the window switch in the “Down” position. Press the driver’s window switch completely down and release it.
Seat Belts and Child Restraint Systems: 3 BEFORE DRIVING Mirrors EXAMPLE WARNING Inside Rearview Mirror 65D410 • Always adjust the mirror with the selector set to the day position. • Only use the night position if it is necessary to reduce glare from the headlights of vehicles behind you. Be aware that in this position you may not be able to see some objects that could be seen in the day position. 52LM012 NOTE: The rear door windows are not designed to open fully.
Seat Belts and Child Restraint Systems: 3 BEFORE DRIVING Outside Rearview Mirrors Power Mirror Control (if equipped) (1) NOTE: If your vehicle is equipped with the heated outside rearview mirrors, refer to “Heated Rear Window and Heated Outside Rearview Mirrors (if equipped) Switch” in this section. (1) (2) (3) (4) (2) (3) (4) 79J033 79J034 Adjust the outside rearview mirrors so you can just see the side of your vehicle in the mirrors.
Seat Belts and Child Restraint Systems: 3 BEFORE DRIVING Front Seats Adjusting Seat Position Seat Adjustment WARNING Never attempt to adjust the driver’s seat or seatback while driving. The seat or seatback could move unexpectedly, causing loss of control. Make sure that the driver’s seat and seatback are properly adjusted before you start driving.
Seat Belts and Child Restraint Systems: 3 BEFORE DRIVING Adjusting Seatbacks Head Restraints WARNING WARNING All head restraints must be reinstalled to properly protect vehicle occupants. All seatbacks should always be in an upright position when driving, or seat belt effectiveness may be reduced. Seat belts are designed to offer maximum protection when seatbacks are in the upright position. WARNING • Never drive the vehicle with the head restraints removed.
Seat Belts and Child Restraint Systems: 3 BEFORE DRIVING Front Seat Heater (if equipped) EXAMPLE (1) (3) (2) (4) 80J2012 (1) head restraint (2) bars (3) release knob To raise the head restraint, pull upward on the restraint until it clicks. To lower the restraint, push down on the restraint while holding in the release knob (3). If a head restraint must be removed (for cleaning, replacement, etc.), push in the release knob and pull the head restraint all the way out.
Seat Belts and Child Restraint Systems: 3 BEFORE DRIVING CAUTION To avoid damaging the heater element: • Do not subject the front seats to heavy impacts, such as children jumping on them. • Do not cover the seat with any insulating materials such as blankets or cushions. 86G064 Rear Seats Head Restraints Head restraints are designed to help reduce the risk of neck injuries in the case of an accident.
Seat Belts and Child Restraint Systems: 3 BEFORE DRIVING NOTE: It may be necessary to fold forward the seatback to provide enough overhead clearance to remove the head restraint. Rear To raise the rear head restraint, pull upward on the restraint until it clicks. To lower the restraint, push down on the restraint while holding in the release knob (3). If a head restraint must be removed (for cleaning, replacement, etc.), push in the release knob and pull the head restraint all the way out.
Seat Belts and Child Restraint Systems: 3 BEFORE DRIVING Folding Rear Seats The rear seats of your vehicle can be folded forward to provide additional cargo space. 1) Hook the webbing of the outboard lapshoulder belts in the belt hangers. SX4 EXAMPLE CAUTION To fold the rear seats forward: • When you move a seatback, make sure the belt webbing is hooked in the seat belt hangers so the seat belts are not caught by the seatback, seat hinge, or seat latch. This helps prevent damage to the belt system.
Seat Belts and Child Restraint Systems: 3 BEFORE DRIVING 3) For SX4, pull the release lever on the top of each split seat, and fold the seatbacks forward. For SX4 SEDAN, push the release button on the top of each split seat, and fold the seatbacks forward. CAUTION After folding the rear seatback forward, do not allow any foreign material to enter the lock opening. This may cause damage to the inside of the lock and prevent the seatback from being locked securely.
Seat Belts and Child Restraint Systems: 3 BEFORE DRIVING WARNING Do not put your hand into the rear seatback lock opening, or your finger may get caught and be injured. Seat Belts and Child Restraint Systems CAUTION Above the pelvis After securing the rear seatback, make sure that it is locked securely. If it is not, red will appear in the release lever (SX4) or around the release button (SX4 SEDAN).
Seat Belts and Child Restraint Systems: 3 BEFORE DRIVING WARNING Across the pelvis as low as possible across the hips 65D201 WARNING (Continued) • Seat belts should never be worn with the straps twisted and should be adjusted as tightly as is comfortable to provide the protection for which they have been designed. A slack belt will provide less protection than one which is snug.
Seat Belts and Child Restraint Systems: 3 BEFORE DRIVING Lap-Shoulder Belt WARNING (Continued) • Infants and small children should never be transported unless they are properly restrained. Restraint systems for infants and small children can be purchased commercially and should be used. Make sure that the system you purchase meets Federal Motor Vehicle Safety Standards. Read and follow all the directions provided by the manufacturer.
Seat Belts and Child Restraint Systems: 3 BEFORE DRIVING To reduce the risk of sliding under the belt during a collision, position the lap portion of the belt across your lap as low on your hips as possible and adjust it to a snug fit by pulling the shoulder portion of the belt upward through the latch plate. The length of the diagonal shoulder strap adjusts itself to allow freedom of movement.
Seat Belts and Child Restraint Systems: 3 BEFORE DRIVING Seat Belt Reminder When the driver and front passenger don’t buckle their seat belts, the driver’s seat belt reminder light in the instrument cluster and the front passenger’s seat belt reminder light in the information display will come on and a buzzer will sound as a reminder to the driver and front passenger to buckle their seat belts.
Seat Belts and Child Restraint Systems: 3 BEFORE DRIVING Flow chart Driver’s seat belt reminder If the driver’s seat belt remains unbuckled with the ignition key in the “ON” position, the driver’s seat belt reminder works as follows: 1) The driver’s seat belt reminder light will come on for about 20 seconds when the ignition key is turned to the “ON” position then will blink for about 55 seconds. When the light comes on, a buzzer will also sound intermittently for about 6 seconds (Reminder 1).
Seat Belts and Child Restraint Systems: 3 Supplemental Restraint System (advanced air bags): 3, 9, 12 BEFORE DRIVING Front passenger’s seat belt reminder The front passenger’s seat belt reminder will activate only when there is a passenger sitting in the front seat. In some situations, however, such as when you place heavy objects in the front seat, the seat belt reminder can be activated as if there were a passenger present.
Supplemental Restraint System (advanced air bags): 3, 9, 12 BEFORE DRIVING Seat Belt Inspection CAUTION When you move a seatback, make sure the belt webbing is hooked in the seat belt hangers so the seat belts are not caught by the seatback, seat hinge, or seat latch. This helps prevent damage to the belt system. WARNING EXAMPLE Be sure to inspect all seat belt assemblies after any collision.
Supplemental Restraint System (advanced air bags): 3, 9, 12 BEFORE DRIVING Child Restraint Systems Infant restraint - rear seat only EXAMPLE 60G332 Infant restraint - rear seat only 80JC007 Booster seat EXAMPLE EXAMPLE SUZUKI highly recommends that you use a child restraint system to restrain infants and small children. Many different types of child restraint systems are available; make sure that the restraint system you select meets Federal Motor Vehicle Safety Standards.
Supplemental Restraint System (advanced air bags): 3, 9, 12 BEFORE DRIVING WARNING Children could be endangered in a crash if their child restraints are not properly secured in the vehicle. When installing a child restraint system, be sure to follow the instructions below. Be sure to secure the child in the restraint system according to the manufacturer’s instructions. 65D607 65D608 WARNING Do not install a rear-facing child restraint in the front passenger’s seat.
Supplemental Restraint System (advanced air bags): 3, 9, 12 BEFORE DRIVING Installation with Lap-Shoulder Seat Belts (child restraint with no top strap) A-ELR type belt A-ELR type belt EXAMPLE EXAMPLE A-ELR type belt EXAMPLE 83E031 Install your child restraint system according to the instructions provided by the child restraint system manufacturer. If you install the child restraint system in the front seat, be sure to slide the seat to the rearmost position.
Supplemental Restraint System (advanced air bags): 3, 9, 12 BEFORE DRIVING A-ELR type belt A-ELR type belt WARNING EXAMPLE Before installing a child restraint in the rear center seat, follow these steps for secure installation: • Make sure the detachable connector is securely latched and the webbing is not twisted. • Make sure the seat belt is passed through the seat belt guide.
Supplemental Restraint System (advanced air bags): 3, 9, 12 BEFORE DRIVING Installation with the LATCH System To revert from ALR to ELR EXAMPLE 65D267 When you unbuckle the seat belt and allow it to retract to a certain length, the retractor will automatically revert back to the normal ELR mode.
Supplemental Restraint System (advanced air bags): 3, 9, 12 BEFORE DRIVING NOTE: Although there are three rear seating positions, you cannot install three LATCH type child restraints in the rear seats. You can install one or two LATCH restraint(s). Be sure to install the LATCH type child restraint(s) in the outboard seating positions.
BEFORE DRIVING EXAMPLE If your LATCH restraint has rigid lower connecting bars, these general instructions apply: 1) If possible, fold the seatback rearward for easier installation. EXAMPLE EXAMPLE 65D341 65D342 4) Return the seatback to the normal, upright position. Tighten the lower straps as described in the child restraint owner’s manual. Attach the top tether strap, if applicable.
BEFORE DRIVING EXAMPLE EXAMPLE EXAMPLE 54G183 54G184 54G185 3) Use your hands to carefully align the connecting bar tips with the anchors. Take care not to pinch your fingers. 4) Push the child restraint toward the anchors so that the connecting bar tips are partially hooked to the anchors. Use your hands to confirm the position. 5) Grasp the front of the child restraint and push the child restraint forcefully to latch the connecting bars.
BEFORE DRIVING Installation of Child Restraint with Top Strap SX4 EXAMPLE Front 80JS072 SX4 SEDAN EXAMPLE Front Some child restraint systems require the use of a top strap. Top strap anchor brackets are provided in your vehicle at the locations shown in the illustrations. Install the child restraint system as follows: 1) For SX4, remove the luggage compartment cover.
BEFORE DRIVING 5) When routing the top strap, be sure to pass the top strap as shown in the illustration. For SX4 SEDAN, if the top strap cannot be properly tightened when passed under the head restraint as shown in the Type 1 and Type 2 illustrations, pass the top strap over the top of the head restraint as shown in the Type 3 illustration. (Refer to “Head Restraints” section for details on how to raise or lower the head restraint.) 6) Make sure that cargo does not interfere with routing of the top strap.
BEFORE DRIVING WARNING Seat Belt Pretensioner System (for front seat belt only) Your vehicle is equipped with a seat belt pretensioner system at the front seating positions. You can use the pretensioner seat belts in the same manner as ordinary seat belts. Failure to follow these instructions may increase the risk of injury in a crash. • Only use an extender for the person, vehicle and seating position it was provided for.
BEFORE DRIVING The driver and all passengers must be properly restrained by wearing seat belts at all times, whether or not a pretensioner is equipped at their seating position, to help minimize the risk of severe injury or death in the event of a crash. Sit fully back in the seat; sit up straight; do not lean forward or sideways. Adjust the belt so the lap portion of the belt is worn low across the pelvis, not across the waist.
BEFORE DRIVING EXAMPLE 2 10 8 1 7 13 9 8 4 9 6 80J2086 3 Your vehicle is equipped with a Supplemental Restraint System consisting of the following components in addition to a lapshoulder belt at each front seating position. 11 14 11 12 5 3 80J2085 1. Driver’s front air bag 2. Front passenger’s front air bag 3. Seat belt pretensioners 4. Air bag controller 5. Driver’s seat position sensors 6. Occupant classification module 7. “PASS AIR BAG OFF” indicator 8. Forward crash sensors 9.
BEFORE DRIVING Front Air Bags The driver’s front air bag is located behind the center pad of the steering wheel and the front passenger’s front air bag is located behind the passenger’s side of the dashboard. The words “SRS AIRBAG” are molded into the air bag covers to identify the location of the air bags.
BEFORE DRIVING Front air bags will not inflate Front air bags are not designed to inflate in rear impacts, side impacts, rollovers or minor frontal collisions, since they would offer no protection in those types of accidents. Remember, since air bags deploy only one time during an accident, seat belts are needed to restrain occupants from further movements during the accident. Side Air Bags and Side Curtain Air Bags EXAMPLE Therefore, an air bag is NOT a substitute for seat belts.
BEFORE DRIVING Side collision range EXAMPLE EXAMPLE 80J2078 80JM146 Side air bags are located in the part of the front seatbacks closest to the doors. The words “SRS AIRBAG” are indicated on the tag to identify the location of the side air bags. Side curtain air bags are located in the roof lining. The words “SRS AIRBAG” are molded into the pillar to identify the location of the side curtain air bags.
BEFORE DRIVING Side air bags and side curtain air bags will not inflate Side air bags and side curtain air bags will probably not inflate WARNING An air bag supplements, or adds to, the crash protection offered by seat belts. The driver and all passengers must be properly restrained by wearing seat belts at all times, whether or not air bags are mounted at their seating position, to minimize the risk of severe injury or death in the event of a crash.
BEFORE DRIVING Driver’s Seat Position Sensor The driver’s seat is equipped with a seat position sensor to monitor the driver seat fore/aft position. The seat position sensor provides information which is used to judge if the driver’s front air bag should deploy at reduced power or at full power. CAUTION Do not put any cargo or metal objects under the seat. The seat position sensor may not work properly or may be damaged if it is covered with something.
BEFORE DRIVING When the ignition switch is turned to the “ON” position, the “PASS AIR BAG OFF” indicator comes on for several seconds to let you know the system is working. When the front passenger sensing system has turned off the front passenger’s front air bag including the seat belt pretensioner, the “PASS AIR BAG OFF” indicator will come on and stay on to remind you that the front passenger’s front air bag is off.
BEFORE DRIVING The front passenger sensing system is designed to enable the front passenger’s front air bag when the system senses a properly-seated adult in the front passenger’s seat. When the passenger sensing system has allowed the air bag to be enabled, the “PASS AIR BAG OFF” indicator will remain off to remind you that the air bag is active.
BEFORE DRIVING How the System Works WARNING • Do not spill any liquids on the seat. Liquids can damage the sensors under the front seat. • Have the driver’s seat position sensor and the front passenger’s sensor mat inspected by your dealer after a collision. • Do not replace the front seats. If you replace them, the air bags and front passenger sensing system may not work properly. • Do not use a seat cover. If you use a seat cover, the front passenger sensing system may not work properly.
BEFORE DRIVING WARNING 65D610 54G582 • The driver should not lean over the steering wheel. The front passenger should not rest his or her body against the dashboard, or otherwise get too close to the dashboard. For vehicles with side air bags and side curtain air bags, occupants should not lean on or sleep against the door. In these situations, the out-of-position occupant would be too close to an inflating air bag, and may suffer severe injury.
BEFORE DRIVING Servicing the Air Bag System If the air bags inflate, have the air bags and related components replaced by an authorized SUZUKI dealer as soon as possible. If your vehicle ever gets in deep water and the driver’s floor is submerged, the air bag controller could be damaged. If this happens, have the air bag system inspected by the SUZUKI dealer as soon as possible. Special procedures are required for servicing or replacing an air bag.
BEFORE DRIVING Instrument Cluster 1. 2. 3. 4. 5. 6. 7. 8.
BEFORE DRIVING Warning and Indicator Lights Low Tire Pressure Warning Light 52D305 As an added safety feature, your vehicle has been equipped with a tire pressure monitoring system (TPMS) that uses a low tire pressure warning light to inform you when one or more of your tires is significantly under-inflated. When the ignition switch is turned to the “ON” position, this light comes on briefly so you can check that the light is working.
BEFORE DRIVING WARNING If the low tire pressure warning light comes on and stays on, reduce your speed and avoid abrupt steering and braking. Stop in a safe place as soon as possible and check your tires. • If you have a flat tire, replace it with the spare tire. Refer to “Jacking Instructions” in the “EMERGENCY SERVICE” section. Refer to “Replacing Tires and/or Wheels” for instructions on how to restore normal operation of the tire pressure monitoring system after you have had a flat tire.
BEFORE DRIVING 1) Pull off the road and stop carefully. WARNING Remember that stopping distance may be longer, you may have to push harder on the pedal, and the pedal may go down farther than normal. 2) Test the brakes by carefully starting and stopping on the shoulder of the road. 3) If you determine that it is safe, drive cautiously at low speed to the nearest dealer for repairs, or 4) Have the vehicle towed to the nearest dealer for repairs.
BEFORE DRIVING NOTE: When you disconnect and re-connect the battery, ESP® system functions other than ABS will be deactivated and the slip indicator light will blink 1 time per second. For details on how to reactive the ESP® systems, refer to “SLIP Indicator Light” in the “OPERATING YOUR VEHICLE” section. For details of the ESP® systems, refer to “Electronic Stability Program (ESP®)” in the “OPERATING YOUR VEHICLE” section. WARNING ESP® The systems cannot prevent accidents. Always drive carefully.
BEFORE DRIVING Oil Pressure Light Charging Light Driver’s Seat Belt Reminder Light 50G051 50G052 60G049 This light comes on when the ignition switch is turned to the “ON” position, and goes out when the engine is started. The light will come on and remain on if there is insufficient oil pressure. If the light comes on when driving, pull off the road as soon as you can and stop the engine. Check the oil level and add oil if necessary.
BEFORE DRIVING AIR BAG Light Malfunction Indicator Light CAUTION Continuing to drive the vehicle when the malfunction indicator light is on or blinking can cause permanent damage to the vehicle’s emission control system, and can affect fuel economy and driveability. 63J030 65D530 This light monitors inflators, crash sensors, seat belt pretensioners, the front passenger sensing system, and corresponding electrical circuits.
BEFORE DRIVING Low Fuel Warning Light If any door (including the tailgate of SX4) is open when the vehicle is moving, a ding sounds to remind you to close all doors completely. Keyless Start System Indicator Light (if equipped) “CRUISE” Indicator Light (if equipped) 54G343 If this light comes on, fill the fuel tank immediately. When this light comes on, a ding sounds once to remind you to fill the fuel. If you do not fill the fuel, a ding sounds every time when the ignition switch is turned to “ON”.
BEFORE DRIVING Illumination Indicator Light High Beam Indicator Light system inspected SUZUKI dealer. by an authorized If the oil temperature of the parts for i-AWD system is high, this light will blink. The “iAWD AUTO” or “i-AWD LOCK” mode will be changed to the “2WD” mode automatically to prevent a damage of the parts for iAWD system. 64J045 50G056 This indicator light comes on while the position lights, tail light and/or the headlights are on.
BEFORE DRIVING intelligent All Wheel Drive (i-AWD) LOCK Indicator Light (if equipped) For details of the “i-AWD LOCK” mode, refer to “Using the 2WD/i-AWD Switch” in the “OPERATING YOUR VEHICLE” section. Speedometer EXAMPLE CAUTION Do not operate your vehicle in “iAWD LOCK” mode on dry hard surfaces. 79J100 When the ignition switch is turned to the “ON” position, this light comes on briefly so you can check that the light is working. Daytime Running Light (D.R.L.
BEFORE DRIVING Tachometer Fuel Gauge EXAMPLE If the low fuel warning light (1) comes on, fill the fuel tank immediately. When the low fuel warning light (1) comes on, a ding sounds once to remind you to fill the fuel. If you do not fill the fuel, a ding sounds every time when the ignition switch is turned to “ON”. (2) CAUTION Avoid driving with an extremely low fuel level. Running out of fuel could cause the engine to misfire, damaging the catalytic converter.
BEFORE DRIVING Temperature Gauge Information display Display (E) Clock (if equipped) Instantaneous Fuel Consumption The display (A) shows instantaneous fuel consumption with a bar graph only when the vehicle is moving. (A) (B) (D) (1) EXAMPLE (C) (E) (3) (2) 80JM103 When the ignition switch is in the “ON” position, this gauge indicates the engine coolant temperature. Under normal driving conditions, the indicator should stay within the normal, acceptable temperature range between “H” and “C”.
BEFORE DRIVING You can turn off or on the indication of instantaneous fuel consumption according to the following instruction. indication of instantaneous fuel consumption. EXAMPLE WARNING EXAMPLE If you attempt to adjust the display while driving, you could lose control of the vehicle. Do not attempt to adjust the display while driving. 80J2027 1) Change the display (B) to the driving range by pushing the indicator selector knob (2).
BEFORE DRIVING (a) (b) (c) (d) (e) Trip meter A Trip meter B Average fuel consumption Driving range Thermometer WARNING If you attempt to adjust the display while driving, you could lose control of the vehicle. Do not attempt to adjust the display while driving. NOTE: • Indications will change when you push and release a knob. • The display shows estimated values. Indications may not be the same as actual values.
BEFORE DRIVING Thermometer The thermometer indicates the outside temperature. EXAMPLE Transaxle selector position indicator (for CVT) EXAMPLE EXAMPLE (h) (g) (Initial setting) (f) 80J2032 80J2030 If the outside temperature nears freezing, the mark (f) will appear on the display. NOTE: • The outside temperature indication is not the actual outside temperature when driving at low speed, or when stopped.
BEFORE DRIVING Odometer / Illumination Control Setting When the ignition switch is in the “ON” position, the display (D) shows the odometer. If you turn the indicator selector knob (2) clockwise or counterclockwise, the display will change to the illumination control setting. Odometer The odometer records the total distance the vehicle has been driven. CAUTION Keep track of your odometer reading and check the maintenance schedule regularly for required services.
BEFORE DRIVING WARNING If you attempt to adjust the display while driving, you could lose control of the vehicle. Do not attempt to adjust the display while driving. NOTE: • If you push the indicator selector knob or do not turn the knob for more than 5 seconds while activating the illumination control, the illumination control will be canceled automatically and the display (D) will show the odometer indication.
BEFORE DRIVING Lighting Operation Daytime Running Light (D.R.L.) System EXAMPLE The headlights light, but are dimmer than the low beam, when the following three conditions are all met. Also, the D.R.L. indicator light on the instrument panel comes on. EXAMPLE (3) Conditions for D.R.L. system operation: 1) The engine is running. 2) The parking brake is released. 3) The headlights are off. (2) (1) 63J309 63J308 To turn the lights on or off, twist the knob on the end of the lever.
BEFORE DRIVING Front Fog Light Switch (if equipped) Turn Signal Control Lever Turn Signal Operation With the ignition switch in the “ON” position, move the lever up or down to activate the right or left turn signals. Normal turn signal EXAMPLE 65D611 64J058 The front fog light comes on when the fog light switch is pushed in with the headlights are on and the beams set to the low beam position. WARNING To avoid possible injury, do not operate controls by reaching through the steering wheel.
BEFORE DRIVING Hazard Warning Switch Lane change signal Windshield Wiper and Washer Lever EXAMPLE 63J311 Some times, such as when changing lanes, the steering wheel is not turned far enough to cancel the turn signal. For convenience, you can flash the turn signal by moving the lever part way and holding it there. The lever will return to its normal position when you release it. 80JM041 Push in the hazard warning switch to activate the hazard warning lights.
BEFORE DRIVING Windshield Wipers Windshield Washer EXAMPLE EXAMPLE EXAMPLE MIST OFF INT LO HI 63J302 63J301 To turn the windshield wipers on, move the lever down to one of the three operating positions. In the “INT” position (if equipped), the wipers operate intermittently. The “INT” position is very convenient for driving in mist or light rain. In the “LO” position, the wipers operate at a steady low speed. In the “HI” position, the wipers operate at a steady high speed.
BEFORE DRIVING CAUTION To help prevent damage to the windshield wiper and washer system components, you should take the following precautions: • Do not continue to hold in the lever when there is no windshield washer fluid being sprayed or the washer motor can be damaged. • Do not attempt to remove dirt from a dry windshield with the wipers or you can damage the windshield and the wiper blades. Always wet the windshield with washer fluid before operating the wipers.
BEFORE DRIVING Tilt Steering Lock Lever (if equipped) Horn Heated Rear Window and Heated Outside Rearview Mirrors (if equipped) Switch EXAMPLE EXAMPLE Type 1 EXAMPLE LOCK UNLOCK 80J2010 63J026 The lock lever is located under the steering column. To adjust the steering wheel height: 1) Pull up the lock lever to unlock the steering column. 2) Adjust the steering wheel to the desired height and lock the steering column by push down the lock lever.
BEFORE DRIVING When the rear window is misted, push this switch (1) to clear the window. CAUTION The heated rear window and the heated outside rearview mirrors (if equipped) use a large amount of electricity. Be sure to turn off after the window and mirrors have become clear. (2) 80JC040 NOTE: • The defogger will work only when the engine is running. • The defogger will automatically turn off after the defogger remains on for 15 minutes to prevent discharging of the battery.
BEFORE DRIVING MEMO 2-83 80J23-03E
OPERATING YOUR VEHICLE OPERATING YOUR VEHICLE Exhaust Gas Warning ......................................................... 3-1 Daily Inspection Checklist .................................................. 3-1 Ignition Switch ..................................................................... 3-2 Parking Brake Lever ........................................................... 3-6 3 Pedals ................................................................................... 3-7 Starting the Engine ..........
Ignition Switch: 8 OPERATING YOUR VEHICLE Exhaust Gas Warning WARNING 52D334 WARNING Avoid breathing exhaust gases. Exhaust gases contain carbon monoxide, a potentially lethal gas that is colorless and odorless. Since carbon monoxide is difficult to detect by itself, be sure to take the following precautions to help prevent carbon monoxide from entering your vehicle. • Do not leave the engine running in garages or other confined areas.
Ignition Switch: 8 OPERATING YOUR VEHICLE 12)Check all gauges. 13)Make sure that the BRAKE light turns off when the parking brake is released. Once a month, or each time you fill your fuel tank, check the tire pressure using a tire pressure gauge. Also check the tire pressure of the spare tire.
Lighting/Turn Signal Control Lever: 8 OPERATING YOUR VEHICLE Vehicle Without Keyless Start System ACC Accessories such as the radio can operate, but the engine is off. Manual transaxle ON This is the normal operating position. All electrical systems are on. Push START This is the position for starting the engine using the starter motor. The key should be released from this position as soon as the engine starts.
Lighting/Turn Signal Control Lever: 8 Windshield Wiper and Washer Lever: 8 OPERATING YOUR VEHICLE Vehicle With Keyless Start System • If the keyless start system red indicator light illuminates, the remote controller may not be in the vehicle or the battery of the remote controller may be unreliable. (3) (2) (4) (1) EXAMPLE 80J2016 56KN076 The ignition switch can be operated without using an ignition key when the remote controller is in an area of the vehicle other than the rear luggage area.
Windshield Wiper and Washer Lever: 8 Rear Window Wiper/Washer Switch: 8 OPERATING YOUR VEHICLE If you leave any of the doors open with the ignition switch in the “ACC” position for a while (and no key inserted), the engine may not start when you turn the ignition switch to “START”. If the engine does not start, close all doors completely or turn the ignition switch back to the “LOCK” position, then start the engine. • CVT vehicle To turn the ignition switch, push the switch.
Rear Window Wiper/Washer Switch: 8 Tilt Steering Lock Lever: 6 Cruise Control: 7, 8 OPERATING YOUR VEHICLE CAUTION 81A297S Parking Brake Lever • Do not turn the starter motor for more than 15 seconds at a time. If the engine does not start, wait 15 seconds before trying again. If the engine does not start after several attempts, check the fuel and ignition systems or consult your SUZUKI dealer.
Cruise Control: 7, 8 OPERATING YOUR VEHICLE For CVT vehicles, always set the parking brake before moving the gearshift lever to the “P” (Park) position. If you park on an incline and shift into “P” before you set the parking brake, the weight of the vehicle may make it difficult to shift out of “P” when you are ready to drive the vehicle. When preparing to drive the vehicle, move the gearshift lever out of the “P” position before releasing the parking brake.
Cruise Control: 7, 8 Remote Audio Controls: Horn: 6 OPERATING YOUR VEHICLE Clutch Pedal (1) (For manual transaxle) The clutch pedal is used to disengage the drive to the wheels when starting the engine, stopping or shifting the gearshift lever. Depressing the pedal disengages the clutch. CAUTION Do not drive with your foot resting on the clutch pedal. It could result in excessive clutch wear, clutch damage, or unexpected loss of engine braking.
OPERATING YOUR VEHICLE Starting a Cold Engine With your foot off the accelerator pedal, crank the engine by turning the ignition key to “START”. Release the key when the engine starts. Engine Block Heater (if equipped) NOTE: Activate the heater at least four hours before you start the engine. However, as the heating time varies depending on the ambient temperature and other factors, adjust the time by observing the engine cranking condition.
OPERATING YOUR VEHICLE CAUTION Secure the block heater cord back to its original position or to the routed position. A loose cord could get caught in the engine accessory drive belt(s) or other moving parts. Using the Transaxle Manual Transaxle EXAMPLE 3) Close the engine hood securely before starting the engine. 80J2082 Reverse gear: with lifting up ring, shift the gearshift lever to the right, engage gear.
OPERATING YOUR VEHICLE WARNING • Reduce your speed and downshift to a lower gear before going down a long or steep hill. Downshifting will allow the engine to provide braking. Avoid riding the brakes or they may overheat, resulting in brake failure. • When driving on slippery roads, be sure to slow down before downshifting. Large and sudden changes in engine speed may cause loss of traction, which could cause you to lose control.
OPERATING YOUR VEHICLE The gearshift lever has a lock mechanism to help prevent accidental shifting. To shift the gearshift lever: Shift with the lock button (1) pushed in and the brake pedal depressed. Shift with the lock button (1) pushed in. Shift without the lock button (1) pushed in. NOTE: • Always shift the gearshift lever without pushing in the lock button (1) except when you shift from “P” to “R”, from “N” to “R” or from “R” to “P”.
OPERATING YOUR VEHICLE D (Drive) Use this position for all normal driving. With the gearshift lever in “D” range you can get an automatic downshift by pressing the accelerator pedal. The higher the vehicle speed is, the more you need to press the accelerator pedal to get a downshift. Manual mode The CVT can shift gears automatically. When using the manual mode, you can shift gears in the same manner as conventional manual transaxle. To use the manual mode, shift the gearshift lever from “D” to “M”.
OPERATING YOUR VEHICLE NOTE: When you shift gears, the gear may not shift to the desired position. This is to maintain good drivability and to protect the transaxle. NOTE: To shift gears continuously, remove your hand from the gearshift lever, then shift the lever again. You cannot shift gears continuously while holding the lever in the “+” or “–” position.
OPERATING YOUR VEHICLE Canceling the manual mode To cancel the manual mode, shift the gearshift lever from “M” to “D”. Temporary manual mode Pull the shift paddle (if equipped) toward you when driving with the gearshift lever in the “D” position. The information display shows the manual mode indicator (1) and the current gear position (2). EXAMPLE (1) If You Cannot Shift CVT Gearshift Lever Out of “P” (PARK) (1) This procedure is for emergency use only.
OPERATING YOUR VEHICLE Using the 2WD/i-AWD (intelligent All Wheel Drive) Switch (if equipped) 80J009 This i-AWD system enables you to select the driving mode according to the driving conditions by operating the 2WD/i-AWD switch. With this feature, you can select 3 mode positions, “2WD”, “i-AWD AUTO” and “i-AWD LOCK” by operating the 2WD/ i-AWD switch even when the vehicle is moving, provided the front wheels are in the straight ahead position.
OPERATING YOUR VEHICLE From i-AWD AUTO to i-AWD LOCK Push the “i-AWD LOCK” switch for a few seconds until the “i-AWD LOCK” indicator will come on. 79J100 From i-AWD LOCK to i-AWD AUTO Push the “i-AWD LOCK” switch, and the “iAWD AUTO” indicator will come on. From i-AWD AUTO or LOCK to 2WD Push the “2WD” switch, and the “i-AWD AUTO” or “i-AWD LOCK” indicator will turn off. NOTE: • The 2WD/i-AWD switch can be operated when the vehicle is either stopped or moving.
OPERATING YOUR VEHICLE CAUTION Cruise Control (if equipped) Unevenly worn tires can cause problems in the operation of the 2WD/iAWD switch. Be sure to rotate the tires according to the maintenance schedule. Refer to “Tires” and “Maintenance Schedule” in the “INSPECTION AND MAINTENANCE” section for proper tire rotation procedures. WARNING To help avoid loss of vehicle control, do not use the cruise control system when driving in heavy traffic, on slippery or winding roads, or on steep downgrades.
OPERATING YOUR VEHICLE To Set Cruising Speed 1) Turn on the cruise control system by pushing the “CRUISE” switch (1). When the “CRUISE” indicator light comes on, you can set cruising speed. 2) Accelerate or decelerate to the desired speed. 3) Push the “SET/COAST” switch (3) and turn on the “SET” indicator light. Take your foot off the accelerator pedal and the set speed will be maintained.
OPERATING YOUR VEHICLE To Change Cruising Speed Using the accelerator pedal To reset at a faster cruising speed, accelerate to the desired speed using the accelerator pedal and push the “SET/COAST” switch (3). The new speed will be maintained. Using the brake pedal To reset at a slower cruising speed, decelerate to the desired speed using the brake pedal and push the “SET/COAST” switch (3). The new speed will be maintained.
OPERATING YOUR VEHICLE WARNING If water gets into the brake drums, brake performance may become poor and unpredictable. After driving through water or washing the underside of the vehicle, test the brakes while driving at a slow speed to see if they have maintained their normal effectiveness. If the brakes are less effective than normal, dry them by repeatedly applying the brakes while driving slowly until the brakes have regained their normal effectiveness.
OPERATING YOUR VEHICLE WARNING • On some types of loose surfaces (such as gravel, snow-covered roads, etc.), the stopping distance required for an ABS-equipped vehicle may be slightly greater than for a comparable vehicle with a conventional brake system. With a conventional brake system, skidding tires are able to “plow” the gravel or snow layer, shortening the stopping distance. ABS minimizes this resistance effect. Allow for extra stopping distance when driving on loose surfaces.
OPERATING YOUR VEHICLE How the ABS Works WARNING If the ABS warning light ((1) or (2)) and the Brake system warning light (3) on the instrument panel simultaneously stay on or come on when driving, both anti-lock function and rear brake force control function (proportioning valve function) of the ABS system may have failed. This could cause the rear wheels to skid or the vehicle to spin during braking on a slippery road or hard braking on a dry paved road.
OPERATING YOUR VEHICLE The ESP® has the following three systems: Stability Control System The vehicle stability control system helps provide integrated control of systems such as anti-lock brakes, traction control, engine control, etc. This system automatically controls the brakes and engine to help prevent the vehicle from skidding when cornering on a slippery road surface or when turning the steering wheel abruptly.
OPERATING YOUR VEHICLE The ESP® indicator lights are described below: SLIP Indicator Light 52KM133 When one of the ESP® systems other than ABS is activated, the SLIP indicator light in the instrument cluster blinks 5 times per second. CAUTION If the SLIP indicator light comes on and stays on while driving, there may be a malfunction of the ESP® systems (other than ABS). You should have the systems inspected by an authorized SUZUKI dealer.
OPERATING YOUR VEHICLE Tire Pressure Monitoring System (TPMS) “ESP OFF” switch 62J142 When the “ESP OFF” switch located at the center console is pushed and held to turn off the ESP® systems (other than ABS), the “ESP OFF” indicator light in the instrument cluster comes on. When you have turned the ESP® systems (other than ABS) off, make sure to turn them back on before resuming ordinary driving.
OPERATING YOUR VEHICLE WARNING (Continued) Driving on a significantly underinflated tire causes the tire to overheat and can lead to tire failure. Under-inflation also reduces fuel efficiency and tire tread life, and may affect the vehicle’s handling and stopping ability.
OPERATING YOUR VEHICLE The low tire pressure warning light can come on due to normal causes such as natural air leaks and pressure changes caused by changes in temperature or atmospheric pressure. Adjusting the air pressure in the tires to the pressure shown on the tire information placard should cause the low tire pressure warning light to turn off. If the light turns on again shortly after adjusting the pressure in your tires, you may have a flat tire.
OPERATING YOUR VEHICLE When you turn off the engine, however, the malfunction indicator resets. It takes about ten minutes after restarting the engine for the malfunction to be detected again and for the light to start flashing. WARNING When the malfunction indicator is illuminated, the system may not be able to detect or signal low tire pressure as intended.
OPERATING YOUR VEHICLE WARNING Only use tires and wheels recommended by SUZUKI as standard or optional equipment for your vehicle. Use of tires or wheels not recommended by SUZUKI can result in TPMS failure. Refer to “Tires” in the “INSPECTION AND MAINTENANCE” section for additional information. For Vehicles Sold in U.S.A. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) This device may not cause harmful interference.
OPERATING YOUR VEHICLE MEMO 3-31 80J23-03E
DRIVING TIPS DRIVING TIPS Break-In ................................................................................ 4-1 Catalytic Converter ............................................................. 4-1 Improving Fuel Economy ................................................... 4-2 Highway Driving .................................................................. 4-3 Driving on Hills .................................................................... 4-3 Driving on Slippery Roads .......................
Instrument Panel: 3, 8 DRIVING TIPS Break-In Catalytic Converter CAUTION 52D078S WARNING • Wear Your Seat Belts at All Times. Even though air bags are equipped at the front seating positions, the driver and all passengers should be properly restrained at all times, using the seat belts provided. Refer to the “Seat Belts and Child Restraint Systems” section for instructions on proper use of the seat belts. • Never drive while under the influence of alcohol or other drugs.
Instrument Cluster: 8 DRIVING TIPS Improving Fuel Economy CAUTION To minimize the possibility of catalyst or other vehicle damage: • Maintain the engine in the proper operating condition. • In the event of an engine malfunction, particularly one involving engine misfire or other apparent loss of performance, have the vehicle serviced promptly. • Do not shut off the engine or interrupt the ignition when the transaxle is in gear and the vehicle is in motion.
Warning and Indicator Lights: 8 DRIVING TIPS Highway Driving EXAMPLE 60A183S Keep the air cleaner clean If the air cleaner is clogged with dust, there will be greater intake resistance, resulting in decreased power output and increased fuel consumption. Keep weight to a minimum The heavier the load, the more fuel the vehicle consumes. Take out any luggage or cargo when it is not necessary.
Warning and Indicator Lights: 8 DRIVING TIPS WARNING Driving on Slippery Roads Try not to hold the brake pedal down too long or too often while going down a steep or long hill. This could cause the brakes to overheat, resulting in reduced braking efficiency. Failure to take this precaution could result in loss of vehicle control. CAUTION When descending a down hill, NEVER turn the ignition key to the “OFF” position. Emission control system and CVT (if equipped) damage may result.
Warning and Indicator Lights: 8 DRIVING TIPS CAUTION Do not continue rocking the vehicle for more than a few minutes. Prolonged rocking can cause engine overheating, transaxle or transfer case damage or tire damage. Tire Chains Tire chains should only be used if they are needed to increase traction or are required by law. Make sure that the chains you use are small-link chains or cable-type chains and are the correct size for your vehicle’s tires.
Warning and Indicator Lights: 8 DRIVING TIPS WARNING In addition to following the driving tips in this section, it is important to observe the following precautions. • Make sure your tires are in good condition and always maintain the specified tire pressure. Refer to “Tires” in the “INSPECTION AND MAINTENANCE” section for details. • Do not use tires other than those specified by SUZUKI. Never use different sizes or types of tires on the front and rear wheels.
Warning and Indicator Lights: 8 A/T Selector Position Indicator: 8 Speedometer/Odometer/Trip meter: 8 DRIVING TIPS MEMO 4-7 80J23-03E
OTHER CONTROLS AND EQUIPMENT OTHER CONTROLS AND EQUIPMENT 60G407 Heating and Air Conditioning System ............................... 5-1 Radio Antenna ..................................................................... 5-15 Audio Systems .................................................................... 5-15 Fuel Filler Cap ..................................................................... 5-43 Engine Hood ........................................................................ 5-44 Sun Visor ....
Parking Brake Lever: 6 Pedals: 6 OTHER CONTROLS AND EQUIPMENT Heating and Air Conditioning System There are three types of heating and air conditioning systems as follows: Air Outlet EXAMPLE • Heating System • Manual Heating and Air Conditioning System • Automatic Heating and Air Conditioning System (Climate Control) 80JM044 1. 2. 3. 4. 5.
Pedals: 6 Gearshift Lever: 10 OTHER CONTROLS AND EQUIPMENT Heating System Side outlet Air flow selector (3) Description of Controls (c) (4) (b) (a) (d) (e) 63J048 (1) (2) (3) 63J193 Temperature selector (1) This is used to select the temperature by turning the selector. This is used to select one of the functions described below. Ventilation (a) Blower speed selector (2) This is used to turn on the blower and to select blower speed by turning the selector.
Gearshift Lever: 10 Fuel Filler Cap: 5 OTHER CONTROLS AND EQUIPMENT Heat & defrost (d) Bi-level (b) Air intake selector (4) (f) (g) 79J066 79J068 63J047 Temperature-controlled air comes out of the floor outlets and cooler air comes out of the center and side outlets. When the temperature selector (1) is in the fully COLD position or fully HOT position, however, the air from the floor outlets and the air from the center and side outlets will be the same temperature.
Fuel Filler Cap: 5 Folding Rear Seats: 3 OTHER CONTROLS AND EQUIPMENT System Operating Instructions Natural ventilation Select “VENTILATION” and “FRESH AIR”, the temperature selector to the desired temperature position, and the blower speed selector to “OFF”. Fresh air will flow through the vehicle during driving. Forced ventilation The control settings are the same as for natural ventilation except you set the blower speed selector to a position other than “OFF”.
Folding Rear Seats: 3 OTHER CONTROLS AND EQUIPMENT Manual Heating and Air Conditioning System Air flow selector (3) Ventilation (a) (c) Description of Controls (4) (b) (d) 79J065 (a) (e) Temperature-controlled air comes out of the center and side air outlets. Bi-level (b) 80JC043 (1) (5) (2) This is used to select one of the functions described below. (3) 80JC042 Temperature selector (1) This is used to select the temperature by turning the selector.
Folding Rear Seats: 3 OTHER CONTROLS AND EQUIPMENT Air intake selector (4) Defrost (e) Heat (c) (f) (g) 79J067 79J069 63J047 Temperature-controlled air comes out of the floor outlets and the side outlets, also comes out of the windshield defroster outlets and also comes slightly out of the side defroster outlets. Temperature-controlled air comes out of the windshield defroster outlets, the side defroster outlets and the side outlets. This selector is used to select the following modes.
Folding Rear Seats: 3 OTHER CONTROLS AND EQUIPMENT Air conditioning switch (5) To turn on the air conditioning system, push in the “A/C” switch and set the blower speed selector to a position other than “OFF”. With this “A/C” switch operation, a indicator light will come on when the air conditioning system is on. To turn off the air conditioning system, push the “A/C” switch again. During operation of the air conditioner, you may notice slight changes in engine speed.
Folding Rear Seats: 3 OTHER CONTROLS AND EQUIPMENT Quick cooling (using recirculated air) The control settings are the same as for normal cooling except you select “RECIRCULATED AIR” and the highest blower speed. NOTE: • If you select “RECIRCULATED AIR” for an extended period of time, the air in the vehicle can become contaminated. Therefore, you should occasionally select “FRESH AIR”.
Folding Rear Seats: 3 Armrest: 3 OTHER CONTROLS AND EQUIPMENT Automatic Heating and Air Conditioning System (Climate Control) (1) (2) (3) (4) (5) (6) (7) (8) (9) Description of Controls (1) (7) (9) (8) (6) (4) (2) (5) Temperature selector Blower speed selector Air intake selector Air flow selector Defrost switch “OFF” switch Air conditioning switch “AUTO” switch Display (3) 80J2042 5-9 80J23-03E
Sun Visor: 5 Interior Light Switch: 7 OTHER CONTROLS AND EQUIPMENT Air intake selector (3) Blower speed selector (2) Temperature selector (1) (1) (2) (3) (a) (b) (7) 80J2043 80JM047 80J2044 Turn the temperature selector (1) to adjust the temperature. The blower speed selector (2) is used to turn on the blower and to select blower speed. Push the air intake selector (3) to change between the following modes.
Spot Light: 7 Assist Grips: 3 Coat Hooks: OTHER CONTROLS AND EQUIPMENT “FRESH AIR” and “RECIRCULATED AIR” are selected alternately each time the air intake selector is pushed. NOTE: If you select “RECIRCULATED AIR” for an extended period of time, the air in the vehicle can become contaminated. Therefore, you should occasionally select “FRESH AIR”. Air flow selector (4) Ventilation (c) (c) (d) 79J065 (4) (e) Temperature-controlled air comes out of the center and side air outlets.
Eyeglasses Holder: Engine Hood: 5 OTHER CONTROLS AND EQUIPMENT Defrost switch (5) Heat & defrost (f) Heat (e) 79J067 79J068 Temperature-controlled air comes out of the floor outlets and the side outlets, a small amount of air comes out of the windshield defroster outlets and also comes slightly out of the side defroster outlets. Temperature-controlled air comes out of the floor outlets, the windshield defroster outlets, the side defroster outlets and the side outlets.
Cup Holder and Storage Area: 3 OTHER CONTROLS AND EQUIPMENT System Operating Instructions Defrost Automatic operation (1) NOTE: If the “AUTO” on the display blinks, there is a problem in the heating system and/or air conditioning system. You should have the system inspected by an authorized SUZUKI dealer. (8) 80JM051 Temperature-controlled air comes out of the windshield defroster outlets, the side defroster outlets and the side outlets.
Accessory Socket: 8 Frame Hooks: 5, 6 OTHER CONTROLS AND EQUIPMENT EXAMPLE (11) Manual operation Maintenance You can manually control the climate control system. Set the selectors to the desired positions. If you do not use the air conditioner for a long period, such as during winter, it may not give the best performance when you start using it again. To help maintain optimum performance and durability of your air conditioner, it needs to be run periodically.
Frame Hooks: 5, 6 OTHER CONTROLS AND EQUIPMENT Radio Antenna SX4 SEDAN The radio antenna wire is printed inside the rear window. SX4 EXAMPLE CAUTION Audio Systems There are two types of audio system as shown below: Type 1 • Do not attach any metal objects to the rear window glass, or place metallic film near it. Either of these conditions may cause poor reception or noise. • When cleaning the inside of the rear window, be careful not to scratch or damage the rear window antenna.
OTHER CONTROLS AND EQUIPMENT Precautions Type 2 80J060 AM/FM/XM 6-CD PLAYER WITH CD CHANGER CONTROL • When the inside of the car is very cold and the player is used soon after switching on the heater, moisture may form on the disc or the optical parts of the player and proper playback may not be possible. If moisture forms on the disc, wipe it off with a soft cloth. If moisture forms on the optical parts of the player, do not use the player for about one hour.
OTHER CONTROLS AND EQUIPMENT prevent the system from operating properly. 52D347 52D348 To remove fingermarks and dust, use a soft cloth, and wipe in a straight line from the center of the compact disc to the circumference. Never stick labels on the surface of the compact disc or mark the surface with a pencil or pen. (B) (C) (B) 52D349 Do not use any solvents such as commercially available cleaners, anti-static spray, or thinner to clean compact discs.
OTHER CONTROLS AND EQUIPMENT Basic Operations (1) Power on/off knob Volume control knob (2) Tone/balance/fader control knob (3) Preset button 5 (4) Preset button 6 Type 1 AM/FM/XM CD PLAYER WITH CD CHANGER CONTROL (1) (2) (3) (4) Type 2 AM/FM/XM 6-CD PLAYER WITH CD CHANGER CONTROL (1) (2) (3) (4) 80J061 5-18 80J23-03E
OTHER CONTROLS AND EQUIPMENT Turning power on/off Press the power on/off knob (1). The unit starts in the function mode it was in when the power was turned off last. Adjusting the volume Turn the volume control knob (1). Turning it clockwise increases the volume; turning it counterclockwise decreases the volume. NOTE: While driving, adjust the volume to an extent that sound and/or noise coming from outside the car can be heard.
OTHER CONTROLS AND EQUIPMENT Listening to the Radio Display (C) Type 1 AM/FM/XM CD PLAYER WITH CD CHANGER CONTROL (A) (B) (D) (2) (3) (6) (1) 66J097 (4) (1) (2) (3) (4) (5) (6) Band switch button (FM/AM) Seek up button Seek down button Manual tuning knob Preset buttons (1 to 6) Auto store button (AS)/ Scan button (SCAN) (A) (B) (C) (D) Band Preset channel number Stereo indicator Frequency (5) Type 2 AM/FM/XM 6-CD PLAYER WITH CD CHANGER CONTROL (6) (1) (2) (3) (4) (5) 80J062 5-20 80J23-
OTHER CONTROLS AND EQUIPMENT Selecting the reception band Press the band switch button (1). Each time the button is pressed, the reception band is switched as follows: 66J098 Seek tuning Press the seek up button (2) or the seek down button (3). The unit stops searching for a station at a frequency where a broadcast station is available. Manual tuning Turn the manual tuning knob (4). The frequency being received is displayed. Preset memory 1) Select the desired station.
OTHER CONTROLS AND EQUIPMENT Listening to a CD CAUTION (A) 52D291 52D274 • CDs or CD-ROMs carrying no mark (A) cannot be used. • Some discs previously recorded in CDR\CD-RW format may not be used. • A CD is inserted with its label facing upward. • When there is a CD already loaded in the unit, another CD cannot be loaded at the same time. Do not use force when inserting the CD into the CD insertion slot. • If a blank disc (non-recorded CD-R) is loaded in the unit, the disc will be ejected.
OTHER CONTROLS AND EQUIPMENT Type 1 AM/FM/XM CD PLAYER WITH CD CHANGER CONTROL (Built in CD Player) Display (D) (A) (B) (C) 66J100 (1) (6) (2) (4) (3) (1) (2) (3) (4) (5) (6) CD insertion slot CD eject button Disc button (CD/AUX) Track up button/Fast forward button Track down button/Rewind button Repeat button (RPT) (A) (B) (C) (D) Mode indicator Track number Play time Repeat indicator (5) 80J063 5-23 80J23-03E
OTHER CONTROLS AND EQUIPMENT NOTE: About Single CDs (8 cm CDs) • No adapter is required to play a single CD. • A single CD is inserted from the center of the CD insertion slot. • Since an ejected single CD is not automatically reloaded, be sure to remove the ejected single CD. Loading a CD Insert a CD in the CD insertion slot (1). When a CD is loaded, play starts and the CD indicator (A) lights. Ejecting a CD Press the CD eject button (2).
OTHER CONTROLS AND EQUIPMENT Type 2 AM/FM/XM 6-CD PLAYER WITH CD CHANGER CONTROL (Built-in CD Changer) Display (F) (A) (B) (C) (D) (E) 66J102 (3) (1) (4) (8) (5) (6) (7) (2) (1) (2) (3) (4) (5) (6) (7) (8) Load button (LOAD) Disc select buttons (1 to 6) CD insertion slot CD eject button Disc button (CD/AUX) Track up button/Fast forward button Track down button/Rewind button Repeat button (RPT) (A) (B) (C) (D) (E) (F) Mode indicator Disc number Track number Play time CD indicator Repeat indica
OTHER CONTROLS AND EQUIPMENT NOTE: About Single CDs (8 cm CDs) • Since the unit is not compatible with a single CD, do not load it into the unit. • Keep in mind the fact that a single CD cannot be played even using a single CD adaptor for the unit. • When a single CD is loaded into the unit accidentally, it will be ejected immediately. Please be sure to remove it. If you forcefully try to push it into the unit without removing it, the CD cannot be ejected. This will result in a damage to the mechanism.
OTHER CONTROLS AND EQUIPMENT Ejecting all the CDs Press the CD eject button (4) for 2 seconds or longer. All the CDs will be ejected from the unit in a sequential manner. • Please prepare a location where removed CDs can be stored. • If you leave the ejected CD without removing it, it will be drawn into the unit automatically after about 15 seconds.
OTHER CONTROLS AND EQUIPMENT Listening to an MP3/WMA Disc Display (Type 1) (D) Type 1 AM/FM/XM CD PLAYER WITH CD CHANGER CONTROL (A) (E) (F) (C) (B) (2) (5) 66J104 (3) (4) Display (Type 2) (1) (D) (A) (B) (E) (F) (C) (G) 66J105 Type 2 AM/FM/XM 6-CD PLAYER WITH CD CHANGER CONTROL (2) (5) (3) (4) (1) (1) (2) (3) (4) (5) Sound control knob Repeat button (RPT) Track up button/Fast forward button Track down button/Rewind button Display button (DISP) (A) (B) (C) (D) (E) (F) (G) Folder num
OTHER CONTROLS AND EQUIPMENT What is MP3/WMA? MP3 (MPEG1/2 Audio Layer-III) and WMA (Windows MediaTM Audio) are the compression formats of digital audio. The former is developed by MPEG (Motion Picture Experts Group), and the latter is developed by Microsoft Corporation. Using these compression formats, you can record the contents of about 10 music CDs on a single CD media (This figures refer to data recorded on a 650 MB CD-R or CDRW at a fixed bit rate of 128 kbps and a sampling frequency of 44.1 kHz).
OTHER CONTROLS AND EQUIPMENT • Maximum number of files in one folder: 255 • Maximum depth of trees: 8 • Maximum number of folders: 255 (Root folder is included.) MP3/WMA MODE Selecting a folder Turn the sound control knob (1) to select a folder. Repeat play Press the repeat button (2).
OTHER CONTROLS AND EQUIPMENT Listening to a XM Satellite Radio (Option) Display (C) Type 1 AM/FM/XM CD PLAYER WITH CD CHANGER CONTROL (A) (8) (6) 66J107 (3) (4) (1) (1) (2) (3) (4) (5) (6) (7) (8) (5) (2) (7) XM button Category button (CAT) Seek up button Seek down button Manual tuning knob Display button (DISP) Preset button (1 to 6) Scan button (SCAN) (A) Band (B) Channel number (C) Category indicator Type 2 AM/FM/XM 6-CD PLAYER WITH CD CHANGER CONTROL (8) (6) (B) If you want to purchase X
OTHER CONTROLS AND EQUIPMENT XM MODE Selecting a band Press the XM button (1). Each time the button is pressed, the band changes in the following order. XM1 XM2 Selecting a category Press the seek up button (3) or seek down button (4) to select a category. Displaying the category Press the category button (2) to have the currently selected category appear on the display. XM3 Selecting a channel Turn the manual tuning knob (5) to select a channel.
OTHER CONTROLS AND EQUIPMENT Listening to Audio for AUX (Option) Display Type 1 AM/FM/XM CD PLAYER WITH CD CHANGER CONTROL (A) 66J221 (1) Aux button (CD/AUX) (A) Mode indicator Aux function This system has an external input terminal so you can listen to audio from an external device connected to this unit. (1) Press the aux button (1).
OTHER CONTROLS AND EQUIPMENT Listening to a CD from an External CD Changer (Option) Display (A) (B) (5) (C) (D) 66J113 (3) (4) (1) (G) (E) (F) Type 1 AM/FM/XM CD PLAYER WITH CD CHANGER CONTROL (6) (2) Type 2 AM/FM/XM 6-CD PLAYER WITH CD CHANGER CONTROL (1) (2) (3) (4) (5) (6) Disc button (CD/AUX) Disc select buttons (1 to 6) Track up button/Fast forward button Track down button/Rewind button Repeat button (RPT) Category button (CAT) (A) (B) (C) (D) (E) (F) (G) Mode indicator Disc number Tr
OTHER CONTROLS AND EQUIPMENT Selecting a CD changer mode Press the disc button (1). Each time the button is pressed, the selected CD plays as follows: Built-in CD player Selecting a disc Press the disc select button (2) corresponding to the disc number you want to listen to. Play starts from the first track on the disc. If a disc number having no disc is pressed, the selection will be invalid. Selecting a track • Press the track up button (3) to listen to the next track.
OTHER CONTROLS AND EQUIPMENT Repeat play Press the repeat button (5). Each time the button is pressed, repeat play mode changes as follows: TRACK REPEAT OFF • TRACK REPEAT The indication “TRACK RPT” appears in the display for 2 seconds and then the repeat indicator (E) lights. The track being currently played is played repeatedly. • DISC REPEAT The indication “DISC RPT” appears in the display for 2 seconds and then the repeat indicator (E) lights.
OTHER CONTROLS AND EQUIPMENT Remote Audio Controls (if equipped) To control the volume: • To increase the volume, push the upper part of the switch (1). The volume continues to increase until you release the switch. • To decrease the volume, push the lower part of the switch (1). The volume continues to decrease until you release the switch. • To mute, push the switch (2). To change the selection on a CD: • To advance to the next track on a CD, push the upper part of the switch (4) briefly.
OTHER CONTROLS AND EQUIPMENT Anti-Theft Feature (1) Power on/off knob (2) Track up button/Fast forward button (3) Preset buttons (1 to 6) Type 1 AM/FM/XM CD PLAYER WITH CD CHANGER CONTROL The anti-theft feature is intended to discourage theft or the audio system by preventing the system from operating when it is moved to a different vehicle. This feature works by allowing you to enter a Personal Identification Number (PIN).
OTHER CONTROLS AND EQUIPMENT Setting the Anti-Theft Function Canceling Your Established PIN Setting 1) Turn off the power by pressing the power on/off knob (1). This operation is to be done when you want to cancel the anti-theft function or change your PIN. 66J118 1) Turn off the power by pressing the power on/off knob (1). 4) After you enter your four digit PIN, the display will return to “0000”. 66J118 2) Press the power on/off knob (1) while pressing and holding the track up button (2).
OTHER CONTROLS AND EQUIPMENT Confirming Your Personal Identification Number (PIN) EXAMPLE When the main power source is disconnected such as when you exchange your battery, etc, you will have to confirm your PIN to be able to use the audio system. To confirm your PIN: 66J124 3) Input your PIN. The power of the audio system will turn off and your PIN will be deleted. To change your PIN, first delete your current PIN, then set a new one.
OTHER CONTROLS AND EQUIPMENT Troubleshooting Applicable to every device Phenomenon Power is not turned on. (No sound is produced) Cause Remedy Fuse is blown. Contact your authorized SUZUKI dealer. Connections are not properly made. Contact your authorized SUZUKI dealer. Radio Phenomenon Cause Remedy Too much noise. Not tuned correctly to the frequency of a station. Tune correctly to the station frequency. Stations cannot be selected by seek tuning. There is no station with strong radio waves.
OTHER CONTROLS AND EQUIPMENT Error display This unit has a number of self-diagnostic functions to protect the system. If a problem should occur, the display shows the type of error. Refer to the table below and take proper measures to correct the problem. If the problem is corrected, the unit will operate normally. Error display Measures to be taken CD/CD changer “Mechanical error”. This error display indicates a mechanical failure in the CD changer (failure to change or eject a disc).
OTHER CONTROLS AND EQUIPMENT Fuel Filler Cap SX4 SEDAN The fuel filler cap is located on the left rear side of the vehicle. The fuel filler door can be unlocked by pulling up the opener lever located on the outboard side of the driver’s seat and can be locked by simply closing the door. EXAMPLE SX4 EXAMPLE EXAMPLE Open Close 56KN029 80JC060 EXAMPLE EXAMPLE 79K053 To remove the fuel filler cap: 1) Open the fuel filler door. 2) Remove the cap by turning it counterclockwise.
OTHER CONTROLS AND EQUIPMENT EXAMPLE WARNING (1) If you need to replace the fuel cap, use a genuine SUZUKI cap. Use of an improper cap can result in a malfunction of the fuel system or emission control system. It may also result in fuel leakage in the event of an accident. (2) Engine Hood EXAMPLE 56KN078 NOTE: The cap holder (1) can hold the fuel filler cap (2) when refueling. To reinstall the fuel filler cap: 1) Turn the cap clockwise until you hear several clicks. 2) Close the fuel filler door.
OTHER CONTROLS AND EQUIPMENT Sun Visor Interior Light Switch EXAMPLE EXAMPLE (3) (2) (1) (1) 80JS024 3) Continue to lift up the hood until it is high enough to support with the prop rod. To close the engine hood: 1) Lift the hood up slightly and remove the prop rod from the hole. Put the prop rod back to the holding clip. 2) Lower the hood close to the bumper, then let it drop down. Make sure the hood is securely latched after closing.
OTHER CONTROLS AND EQUIPMENT Luggage Compartment Light (SX4) EXAMPLE Trunk Light (SX4 SEDAN) EXAMPLE (1) (2) 79J075 NOTE: The number of doors involved in the lighting operation of the interior light depends on the vehicle specification. If there is a switch (rubber projection) at the door opening as shown, the door is involved in the lighting operation. The tailgate of SX4 is also involved in this operation even without the rubber projection.
OTHER CONTROLS AND EQUIPMENT Spot Light Accessory Socket (if equipped) Cigarette Lighter and Ashtray (if equipped) Cigarette Lighter (if equipped) 79J074 Push the switch to turn on the light and push it again to turn off the light. 80J2046 The accessory socket will work when the ignition switch is in the “ACC” or “ON” position. This socket can be used to provide 12 volt/ 120 watt power for electrical accessories.
OTHER CONTROLS AND EQUIPMENT Assist Grips (if equipped) Ashtray (if equipped) CAUTION To avoid damage to the cigarette lighter socket, do not use it as an accessory power source. Some accessories’ power plug can damage the inner mechanism of the cigarette lighter socket. EXAMPLE 79J047 You can fit the ashtray into any of the cup holders on the center console. WARNING Make sure tobacco is fully extinguished before closing the ashtrays. Never throw waste in the ashtrays: it could create a fire hazard.
OTHER CONTROLS AND EQUIPMENT Glove Box Cup Holder and Storage Area (if equipped) EXAMPLE WARNING Do not use the cup holder or the storage bin to hold cups containing hot liquids or sharp-edged, hard or breakable objects. Objects in these bins may be thrown about during a sudden stop or impact, and could cause personal injury. Bottle holder Front 79J120 To open the glove box, pull the latch lever. To close it, push the lid until it latches securely.
OTHER CONTROLS AND EQUIPMENT Rear Luggage compartment pocket (SX4) Front Seat Back Pocket (if equipped) EXAMPLE (1) 80JM143 80JM124 You should hold a bottle with a cap in the holder. To open the lid, slide the lever (1) and pull the lid. 80JC089 This pocket is provided for holding light and soft things such as gloves, newspapers or magazines. WARNING Do not put hard or breakable objects in the pocket. If an accident occurs, objects such as bottles, cans, etc.
OTHER CONTROLS AND EQUIPMENT Armrest (if equipped) Shopping Hook (if equipped) Luggage compartment EXAMPLE 80J2068 To use the armrest, pivot it down from the stowed (fully up) position. When not in use, return the armrest to the stowed position. CAUTION To avoid damage to the armrest, do not lean onto it or allow a child ride on it. Floor Mats (if equipped) 80J2014 80JM058 You can hang the shopping bag or other suitable objects on the hook. This hook is not designed for large or heavy items.
OTHER CONTROLS AND EQUIPMENT WARNING Failure to take the following precautions may result in the driver’s side floor mat interfering with the pedals and causing a loss of vehicle control or an accident. • Make sure that the floor mat grommet(s) is(are) hooked to the fastener(s). • Never place additional floor mats on top of the existing floor mats. Luggage Compartment Cover (if equipped) Luggage or other cargo placed in the luggage compartment can be hidden from view by a luggage compartment cover.
OTHER CONTROLS AND EQUIPMENT Luggage Compartment Board (if equipped) To remove the luggage compartment board: 80JM062 80JM060 80JM059 1) Fold the board forward. You can stow the board behind the rear seatback as shown in the illustration. Your vehicle is equipped with the luggage compartment board in the luggage compartment. You can place luggage or other cargos on the board or under the board. You can also place tall luggage by stowing the board on the floor of the luggage compartment.
OTHER CONTROLS AND EQUIPMENT To re-install the luggage board to the normal position: To install the luggage board on the floor of the luggage compartment: (2) (1) 80JM145 80JM144 80JM129 Place the strikers of the luggage board to the latches on the side and tail end of original position. 1) Unfold the luggage compartment board (1), and insert it along the groove (2) at both side of the luggage compartment as shown in the illustration. 2) Slide the board forward.
OTHER CONTROLS AND EQUIPMENT Roof Rails or Roof Rack Anchors (if equipped) You can use the roof rails or the roof rack anchors to attach the optional roof rack which is available at your SUZUKI dealer. If you use a roof rack, observe the instructions and precautions in this section and provided with the roof rack. Roof rails 79J167 Roof rack anchors 80J082 • Make sure the roof rack is securely installed. • To mount various types of cargo (such as skis, bicycles, etc.
OTHER CONTROLS AND EQUIPMENT Frame Hooks Front bumper cover (if equipped) CAUTION SX4 If towing your vehicle, use the frame hook of removed bumper cover side to prevent damage to the vehicle. Front (1) (d) EXAMPLE NOTE: When return the cover, make sure the ungual (d) of the cover securely fit to the slit on under the front bumper of vehicle.
OTHER CONTROLS AND EQUIPMENT SX4 Side (3) Frame hooks are provided on the front (1), rear (2) and side (3) of the vehicle. The hooks (1) and (2) are used for emergency situations. The hooks (3) are used for trailer/train shipping purposes. Rear (2) To tow your vehicle on the road or highway, follow the instruction of “Towing” in “EMERGENCY SERVICE” section.
VEHICLE LOADING AND TOWING VEHICLE LOADING AND TOWING Vehicle Loading ................................................................... 6-1 Trailer Towing ...................................................................... 6-2 Towing Your Vehicle (recreational towing) ......................
Exhaust Gas Warning: NO Daily Inspection Checklist: NO VEHICLE LOADING AND TOWING Vehicle Loading Vehicle Capacity Weight – Maximum permissible load weight a vehicle can carry including the weight of all the occupants, accessories and cargo. The weight of any accessories already installed on your vehicle at the time of purchase, or that you or the dealer install after purchase, must be subtracted from the Vehicle Capacity Weight to determine how much capacity remains available for occupants and cargo.
Daily Inspection Checklist: NO Starting the Engine: 1 VEHICLE LOADING AND TOWING Trailer Towing Towing Your Vehicle (recreational towing) Your vehicle may be towed behind another vehicle (such as a motorhome), provided you use the proper towing method specified for your vehicle. The towing method you must use depends on the specifications of your vehicle: whether it is a 2wheel drive (2WD) or intelligent All Wheel Drive (i-AWD) vehicle. 54G639 Do not use your vehicle to tow a trailer.
Engine Block Heater: 1 VEHICLE LOADING AND TOWING A: 2WD (except 2WD mode of i-AWD) VEHICLES WITH MANUAL TRANSAXLE OR CVT 1) Secure the front wheels on a towing dolly according to the instructions provided by the dolly manufacturer. 2) Release the parking brake. TOWING METHOD A FROM THE FRONT: FRONT WHEELS ON A DOLLY AND REAR WHEELS ON THE GROUND 80J2053 CAUTION 80J2052 Towing the 2WD or i-AWD CVT vehicles with four wheels on the ground can result in damage to the CVT.
Using the Transaxle: 10 VEHICLE LOADING AND TOWING B: 2WD or i-AWD (including 2WD mode) VEHICLES WITH MANUAL TRANSAXLE 1) Shift the manual transaxle lever into neutral. 2) Turn the ignition key to the “ACC” position to unlock the steering wheel. 3) Release the parking brake. TOWING METHOD B FROM THE FRONT: FOUR WHEELS ON THE GROUND CAUTION The steering column is not strong enough to withstand shocks transmitted from the front wheels during towing. Always unlock the steering wheel before towing.
Using the Transaxle: 10 VEHICLE LOADING AND TOWING MEMO 6-5 80J23-03E
INSPECTION AND MAINTENANCE INSPECTION AND MAINTENANCE 60G410 Maintenance Schedule ....................................................... 7-2 Periodic Maintenance Schedule ........................................ 7-3 Maintenance Recommended under Severe Driving Conditions ........................................................................... 7-7 Drive Belt ............................................................................. 7-11 Engine Oil and Filter ........................................
Highway Driving: NO Driving on Hills: NO INSPECTION AND MAINTENANCE WARNING 60A187S WARNING You should take extreme care when working on your vehicle to prevent accidental injury. Here are a few precautions that you should be especially careful to observe: • To prevent damage or unintended inflation of the air bag system, be sure the battery is disconnected and the ignition switch has been in the “LOCK” position for at least 90 seconds before performing any electrical service work on your SUZUKI.
Driving on Hills: NO Driving on Slippery Roads: NO INSPECTION AND MAINTENANCE NOTICE (for U.S.A.) Maintenance, replacement or repair of the emission control devices and systems may be performed by any automobile repair establishment or individual using any part which has been certified under the provisions in the Clean Air Act sec. 207. (a) (2). Maintenance Schedule The following table shows the times when you should perform regular maintenance on your vehicle.
Driving on Slippery Roads: NO INSPECTION AND MAINTENANCE Periodic Maintenance Schedule R: Replace or change I : Inspect, clean, adjust, lubricate or replace as necessary Interval: This interval should be judged by miles (x 1000) odometer reading or months, whichever comes km (x 1000) first. months ENGINE & EMISSION CONTROL 1. Drive belt Inspect for damage *2. Valve lash (clearance) 3. Engine oil and oil filter *4. Cooling system hoses and connections 5. Engine coolant *6. Exhaust pipes and mountings *7.
Driving on Slippery Roads: NO INSPECTION AND MAINTENANCE R: Replace or change I : Inspect, clean, adjust, lubricate or replace as necessary Interval: This interval should be judged by miles (x 1000) odometer reading or months, whichever comes km (x 1000) first. months ENGINE & EMISSION CONTROL 1. Drive belt Inspect for damage *2. Valve lash (clearance) 3. Engine oil and oil filter *4. Cooling system hoses and connections 5. Engine coolant *6. Exhaust pipes and mountings *7. EVAP canister *8.
INSPECTION AND MAINTENANCE R: Replace or change I : Inspect, clean, adjust, lubricate or replace as necessary miles (x 1000) Interval: This interval should be judged by odometer km (x 1000) reading or months, whichever comes first. months CHASSIS AND BODY 1. Clutch (for manual transaxle) Pedal and fluid level *2. Brake discs and pads (front, rear) Brake drums and shoes (rear) *3. Brake hoses and pipes 4. Brake fluid level check, *replacement 5. Brake pedal stroke check, *adjustment 6.
INSPECTION AND MAINTENANCE R: Replace or change I : Inspect, clean, adjust, lubricate or replace as necessary miles (x 1000) Interval: This interval should be judged by odometer km (x 1000) reading or months, whichever comes first. months CHASSIS AND BODY 1. Clutch (for manual transaxle) Pedal and fluid level *2. Brake discs and pads (front, rear) Brake drums and shoes (rear) *3. Brake hoses and pipes 4. Brake fluid level check, *replacement 5. Brake pedal stroke check, *adjustment 6.
INSPECTION AND MAINTENANCE Maintenance Recommended under Severe Driving Conditions Follow this schedule if your car is mainly operated under one or more of the following conditions: • When most trips are less than 6 kilometers (4 miles) • When most trips are less than 16 kilometers (10 miles) and outside temperature remain below freezing. • Idling and/or low-speed operation in stop-and-go traffic. • Operating in dusty areas.
INSPECTION AND MAINTENANCE R: Replace or change I : Inspect, clean, adjust, lubricate or replace as necessary Interval: This interval should be judged by miles (x 1000) odometer reading or months, whichever km (x 1000) comes first. months 42 70 42 45 75 45 48 80 48 51 85 51 54 90 54 57 95 57 60 100 60 63 105 63 66 110 66 69 115 69 ENGINE & EMISSION CONTROL 1. Drive belt Inspect for damage – – – – – – I – – – *2. Valve lash (clearance) – – – – – – I – – – 3.
INSPECTION AND MAINTENANCE R: Replace or change I : Inspect, clean, adjust, lubricate or replace as necessary miles (x 1000) Interval: This interval should be judged by odometer km (x 1000) reading or months, whichever comes first. months CHASSIS AND BODY 1. Clutch (for manual transaxle) Pedal and fluid level *2. Brake discs and pads (front, rear) Brake drums and shoes (rear) *3. Brake hoses and pipes 4. Brake fluid level check, *replacement 5. Brake pedal stroke check, *adjustment 6.
INSPECTION AND MAINTENANCE R: Replace or change I : Inspect, clean, adjust, lubricate or replace as necessary miles (x 1000) Interval: This interval should be judged by odometer km (x 1000) reading or months, whichever comes first. months CHASSIS AND BODY 1. Clutch (for manual transaxle) Pedal and fluid level *2. Brake discs and pads (front, rear) Brake drums and shoes (rear) *3. Brake hoses and pipes 4. Brake fluid level check, *replacement 5. Brake pedal stroke check, *adjustment 6.
INSPECTION AND MAINTENANCE Drive Belt WARNING Engine Oil and Filter Oil Level Check Specified Oil Engine oil dipstick When the engine is running, keep hands, hair, clothing, tools, etc. away from the moving fan and drive belts. Check the accessory drive belt only for damage. You do not need check it for tension as it has an automatic tensioner. “Starburst” If you need to replace or adjust the belt have it done by your SUZUKI dealer. L4 2.
INSPECTION AND MAINTENANCE EXAMPLE Refilling FULL ADD Changing Engine Oil and Filter EXAMPLE Open EXAMPLE Close 52D084 The handle of the engine oil dipstick is colored yellow for easy identification. Pull out the oil dipstick, wipe oil off with a clean cloth, insert the dipstick all the way into the engine, then remove it again. The oil on the stick should be between the upper and lower limits shown on the stick.
INSPECTION AND MAINTENANCE Replace the Oil Filter WARNING New and used oil and solvent can be hazardous. Children and pets may be harmed by swallowing new or used oil or solvent. Repeated, prolonged contact with used engine oil may cause [skin] cancer. Brief contact with used oil or solvent may irritate skin. • Keep new and used oil and solvent away from children and pets. • Wear a long-sleeve shirt and waterproof gloves. • Wash with soap if oil or solvent contacts your skin.
INSPECTION AND MAINTENANCE NOTE: When it is difficult to remove the oil filter, we recommend you take your vehicle to your SUZUKI dealer for oil filter replacement. Engine Coolant EXAMPLE Selection of Coolant CAUTION SUZUKI LLC: Super (Blue) coolant; SUZUKI LLC: Super (Blue) coolant is already diluted to the proper percentage. Do not dilute with distilled water additionally. Doing so may result in the possibility of freezing coolant and/or overheating.
INSPECTION AND MAINTENANCE Failure to use the proper coolant can damage your cooling system. Your authorized SUZUKI dealer can help you select the proper coolant. CAUTION To avoid damaging your cooling system: • Always use a high quality ethylene glycol base phosphate type coolant diluted with distilled water at the correct mixture concentration. • Make sure that the proper mix is 50/ 50 coolant to distilled water and in no case higher than 70/30.
INSPECTION AND MAINTENANCE CAUTION Air Cleaner Spark Plugs You should inspect spark plugs periodically for carbon deposits. When carbon accumulates on a spark plug, a strong spark may not be produced. Remove carbon deposits with a wire or pin and adjust the spark plug gap. SUZUKI LLC: Standard (Green) coolant; • The mixture you use should contain 50% concentration of antifreeze.
INSPECTION AND MAINTENANCE EXAMPLE (4) 80J2070 2) Disconnect the coupler (4) while pushing the release lever, 3) Remove the bolt, and 4) Pull the ignition coil out. CAUTION • When servicing the iridium/platinum spark plugs (slender center electrode type plugs), do not touch the center electrode, as it is easy to damage. • When installing the spark plugs, screw them in with your fingers to avoid stripping the threads. Tighten with a torque wrench to 25 Nm (2.5 kg-m, 18.0 lb-ft).
INSPECTION AND MAINTENANCE Gear Oil Manual transaxle API GRADE Specified Gear Oil When replacing gear oil, use gear oil with the appropriate viscosity and grade as shown in the charts below.
INSPECTION AND MAINTENANCE Gear Oil Level Check Rear differential (i-AWD) The manual transaxle, transfer gears (iAWD CVT) and rear differential (i-AWD) are lubricated with gear oil. To check the gear oil level in any of the above locations, use the following procedure: (1) 80J015 (1) Oil filler and level plug Tightening torque Oil Filler Plug Manual transaxle Transfer Rear differential 27 Nm (19.5 lb-ft) (2.7 kg-m) 23 Nm (16.6 lb-ft) (2.3 kg-m) Clutch Pedal 1) Park the vehicle on a level surface.
INSPECTION AND MAINTENANCE Use a CVT fluid SUZUKI CVT FLUID GREEN-1 or Shell GREEN-1V. Fluid Level Check CAUTION Driving with too much or too little fluid can damage the transaxle. You must check the fluid level with the CVT fluid at normal operating temperature. To check the fluid level: 1) To warm up the transaxle fluid, drive the vehicle or idle the engine until the temperature gauge indicates normal operating temperature. 2) Then drive for ten more minutes.
INSPECTION AND MAINTENANCE 6) The handle of the CVT fluid dipstick is colored red or orange for easy identification. Remove the dipstick, clean it and push it back in until the cap seats. Pull out the dipstick and read the fluid level. The fluid level should be between the two marks in the “HOT” range on the dipstick. 7) Add just enough specified fluid through the dipstick hole to fill the transaxle to the proper level. It takes only 0.6 liters (1.27 US pt) for CVT to raise the level from “LOW” to “FULL”.
INSPECTION AND MAINTENANCE WARNING (Continued) • Do not use any fluid other than SAE J1703 or DOT3 brake fluid. Do not use reclaimed fluid or fluid that has been stored in old or open containers. It is essential that foreign particles and other liquids are kept out of the brake fluid reservoir. NOTE: With disc brakes, the fluid level can be expected to gradually fall as the brake pads wear. measured above is less than the minimum distance required, have your vehicle inspected by your SUZUKI dealer.
INSPECTION AND MAINTENANCE Steering Wheel Parking Brake Lever WARNING If you experience any of the following problems with your vehicle’s brake system, have the vehicle inspected immediately by your SUZUKI dealer. • Poor braking performance • Uneven braking (brakes not working uniformly on all wheels.) • Excessive pedal travel • Brake dragging • Excessive noise • (Except ABS equipped vehicle) Pedal pulsation (pedal pulsates when pressed for braking.
INSPECTION AND MAINTENANCE Tires Power Steering (if equipped) For safe operation of your vehicle, it is important that the tires be the correct type and size, in good condition, and properly inflated. Be sure to follow the requirements and recommendations in this section. EXAMPLE Tire Sidewall Labeling Useful information about a tire is molded into its sidewall. The example below shows a typical passenger car tire.
INSPECTION AND MAINTENANCE F. Load Rating Load rating is the maximum weight a tire is designed to support in normal service. G. Max Inflation Pressure Max inflation pressure is the maximum inflation pressure a tire is designed for. H. Tire Ply Material These tire markings describe the type of cord and number of plies in the sidewall and under the tread. I.
INSPECTION AND MAINTENANCE D. Construction Code This letter code is used to indicate the type of ply construction in the tire. The letter “R” means radial ply tire construction, the letter “D” means diagonal or bias ply construction, and the letter “B” means belted-bias ply construction. E. Rim Diameter This two-digit number is the wheel or rim diameter in inches. Tire Inflation Pressure Tire inflation pressure should be checked when the tire is cold.
INSPECTION AND MAINTENANCE NOTE: The tire inflation pressure will change due to changes in atmospheric pressure, temperature or tire temperature when driving. To reduce the chance that the low tire pressure warning light will come on due to normal changes in temperature and atmospheric pressure, it is important to check and adjust the tire pressures when the tires are cold.
INSPECTION AND MAINTENANCE Tire Inspection Inspect your vehicle’s tires at least once a month by performing the following checks: 1) Measure the air pressure with a tire gauge. Adjust the pressure if necessary. Remember to check the spare tire, too. Refer to the “Measuring Air Pressure” section. 1.6 mm (0.06 in.) or less and the tire should be replaced. 3) Check for abnormal wear, cracks and damage. Any tires with cracks or other damage should be replaced.
INSPECTION AND MAINTENANCE WARNING Replacing the wheels and tires equipped on your vehicle with certain combinations of aftermarket wheels and tires can significantly change the steering and handling characteristics of your vehicle. Oversized tires may also rub against the fender over bumps, causing vehicle damage or tire failure. Therefore, use only those wheel and tire combinations approved by SUZUKI Motor Corporation as standard or optional equipment for your vehicle.
INSPECTION AND MAINTENANCE Temperature – A, B, C The temperature grades are A (the highest), B and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure.
INSPECTION AND MAINTENANCE Compact Spare Tire (if equipped) Note that two or more compact spare tires should not be used on one vehicle simultaneously. WARNING 54G115 (1) Wear indicator (2) Indicator location mark Your vehicle comes equipped with the compact spare tire. The compact spare is designed to save space in your storage area, and its lighter weight makes it easier to install if a flat tire occurs.
INSPECTION AND MAINTENANCE Snow Tires Your vehicle is equipped with all-season tires which are designed for use in summer and most winter conditions. For improved traction in severe winter conditions, SUZUKI recommends mounting radial snow tires on all four wheels. Snow tires must be the same size as the standard tires. Also be sure to use the tires of the same type and brand on all four wheels of your vehicle.
INSPECTION AND MAINTENANCE Vehicle Capacity Weight – the rated cargo and luggage load plus 68 kilograms (150 lbs) times the vehicle’s designated seating capacity. Vehicle Maximum Load on the Tire – the load on an individual tire that is determined by distributing to each axle its share of the maximum loaded vehicle weight and dividing by two.
INSPECTION AND MAINTENANCE trailer). Contact your dealer for further information. Actual weight of the loaded vehicle and actual loads at the front and rear axles can only be determined by weighing the vehicle using a vehicle scale. To measure the weight and load, try making your vehicle to a highway weighing station, shipping company or inspection station for trucks, etc. Compare these weights to the GVWR and GAWR (front and rear) listed on the Safety Certification Label.
INSPECTION AND MAINTENANCE Vehicle Loading Example As an example, suppose that the Tire and Loading Information label on your vehicle indicates that your vehicle’s total load capacity is 950 lbs. If you were to drive your vehicle with one passenger, and the total combined weight of you and your passenger was 350 lbs, then the cargo and luggage capacity of your vehicle would be 600 lbs (950 – 350 = 600 lbs).
INSPECTION AND MAINTENANCE WARNING To avoid harm to yourself or damage to your vehicle or battery, follow the jump starting instructions in the “EMERGENCY SERVICE” section of this manual if it is necessary to jump start your vehicle. WARNING Battery posts, terminals and related accessories contain lead and lead compounds. Wash hands after handling. Your vehicle is equipped with a battery that requires infrequent maintenance. You will never have to add water.
INSPECTION AND MAINTENANCE MAIN FUSE / PRIMARY FUSE (20) – Automatic transaxle relay (21) – Air compressor relay (22) – Fuel pump relay (23) – Condenser fan relay (1) 80A All electric load (2) 50A Power window, Ignition, Wiper, Starter – Front fog light relay 50A Tail light, Rear defogger, Door lock, Hazard/Horn, Dome (24) (3) (25) – Throttle motor relay (4) – Blank (26) – FI MAIN relay – Starting motor relay (5) – Blank (27) (6) 15A Head light (Right) fuse (28) –
INSPECTION AND MAINTENANCE Fuses under the Dash Board MAIN FUSE / PRIMARY FUSE (21) 30A Rear defogger (22) 15A Horn / Hazard (23) – (1) 15A Rear wiper (2) 15A Ignition coil (3) 10A Back-up light (4) 10A Meter (5) 15A Accessory (6) 15A Accessory 2 (7) 30A Power window (1) (2) (3) (4) (5) (6) (8) 30A Wiper (8) (9) (10) (11) (12) (13) (14) (15) (16) (9) 10A IG1 SIG (10) 15A Air bag (11) 10A Anti-lock brake system (12) 15A 4WD (13) 10A Stop light (8) (9) (10) (1
INSPECTION AND MAINTENANCE (8) 30A Wiper Headlight Aiming (9) 10A IG1 SIG (10) 15A Air bag Since special procedures are required, we recommend you take your vehicle to your SUZUKI dealer for headlight alignment.
INSPECTION AND MAINTENANCE Bulb Replacement Center Interior Light (if equipped) Spot light WARNING • Light bulbs can be hot enough to burn your finger right after being turned off. This is true especially for halogen headlight bulbs. Replace the bulbs after they become cool enough. • The headlight bulbs are filled with pressurized halogen gas. They can burst and injure you if they are hit or dropped. Handle them carefully.
INSPECTION AND MAINTENANCE Headlights Other General Lights Bulb EXAMPLE Bulb holder EXAMPLE (1) (2) (1) (1) (3) (2) (4) (1) (2) 54G124 (2) 54G123 (1) Removal (2) Installation To remove a bulb holder from a light housing, turn the holder counterclockwise and pull it out. To install the holder, push the holder in and turn it clockwise. 80J2084 Open the engine food. Disconnect the coupler (1). Then remove the socket cover (2) and replace the bulb.
INSPECTION AND MAINTENANCE Front turn signal light (1) Front position light (2) (1) Front fog light (if equipped) 1) Start the engine. Turn the steering wheel to the opposite side of the replacing fog light to replace the bulb easily. Then turn off the engine. (2) EXAMPLE EXAMPLE (1) (3) (2) 80JM115 3) Remove the bolts (3). 80JM123 80JM114 2) Insert a flat blade screwdriver into the hole (2) and remove the clips (1) by twist the driver as shown in the illustration.
INSPECTION AND MAINTENANCE SX4 5) Remove the front fog light. Turn the bulb holder counterclockwise and remove it. (4) Rear combination light (tail, stop, turn signal, etc.) SX4 SX4 SEDAN EXAMPLE (5) 80JM116 4) Open the fender cover. Disconnect the coupler by pushing the lock release. Pinch both side of the clips (4) and (5), and push them in. 80JM131 80JM071 4) Open the fender cover. Disconnect the coupler with pushing the lock release. Turn the bulb holder counterclockwise and remove it.
INSPECTION AND MAINTENANCE To open the trim (1), insert a flat blade screwdriver between the trim and the clips (2) and remove the clips by twist the driver as shown in the illustration. License plate light To open the trim (1), insert a flat blade screwdriver into the hole (3) and remove the clips (2) by twist the driver as shown in the illustration.
INSPECTION AND MAINTENANCE Luggage compartment light (SX4) High-mount stop light (if equipped) SX4 (2) 79J015 Trunk room light (SX4 SEDAN) (1) 63J127 80J100 To remove a high-mounted stop light housing the following procedure: 2) Close the tailgate. Remove a highmounted stop light housing (2) from the tailgate. 1) Open the tailgate, and remove the nuts (1) as shown in the illustration.
INSPECTION AND MAINTENANCE Wiper Blades SX4 SEDAN (3) (4) (3) 80JM076 3) Pushing the unguiform prongs (3) toward inside and remove the bulb holder (4). 4) Replace the bulbs. To install a high-mounted stop light housing in the reverse order of removal. 80G083 If the wiper blades become brittle or damaged, or make streaks when wiping, replace the wiper blades. (1) To install new wiper blades, follow the procedures below.
INSPECTION AND MAINTENANCE For windshield wipers and some rear wipers: 70G119 1) Hold the wiper arm away from the window. 52D102 60A260 2) Squeeze lock lever (1) towards wiper arm (2) and remove the wiper frame from the arm as shown. 3) Pull the locked end of the wiper blade firmly to unlock the blade and slide the blade out as shown. NOTE: When raising both of the front wiper arms, pull the driver’s side wiper arm up first. When returning the wiper arms, lower the passenger’s side wiper arm first.
INSPECTION AND MAINTENANCE To remove some types of rear wiper frame from the wiper arm: 1) Hold the arm away from the window. Installation 52D124 (3) Retainer 4) If the new blade is provided without the two metal retainers, move them from the old blade to the new one. 52D125 (4) Locked end 5) Install the new blade in the reverse order of removal, with the locked end positioned toward the wiper arm. Make sure the blade is properly retained by all the hooks.
INSPECTION AND MAINTENANCE 3) When reinstalling wiper frame to arm, install the wiper frame in the reverse order of removal. To remove and install some types of rear wiper blade from and to the wiper frame. Installation To remove and install some types of rear wiper blade from and to the wiper frame. Removal 60A265 2) Install the new blade in the reverse order of removal. Make sure that the blade is properly retained by all the hooks and the end is locked in place.
INSPECTION AND MAINTENANCE Windshield Washer Fluid Check that there is washer fluid in the tank by looking at the washer fluid level gauge which is attached to the cap of the washer fluid tank. If the fluid level is near “E” mark, refill it. Use a good quality windshield washer fluid, diluted with water as necessary. WARNING Do not use “anti-freeze” solution in the windshield washer reservoir. This can severely impair visibility when sprayed on the windshield, and also damage your vehicle’s paint.
INSPECTION AND MAINTENANCE MEMO 7-51 80J23-03E
EMERGENCY SERVICE EMERGENCY SERVICE Tire Changing Tool ............................................................. 8-1 Jacking Instructions ........................................................... 8-2 Changing Wheels ................................................................ 8-4 Jump Starting Instructions ................................................ 8-5 Towing a Disabled Vehicle ................................................. 8-6 If the Starter Does Not Operate ............................
Vehicle Loading: 11 EMERGENCY SERVICE Tire Changing Tool SX4 SX4 EXAMPLE (1) 80J048 80JC014 To remove the spare tire, turn its bolt (1) counterclockwise and remove it. 79J086 SX4 SEDAN SX4 SEDAN EXAMPLE EXAMPLE 80JC045 The jack, wheel brace, jack handle are stowed in the luggage compartment. 79J085 80JC015 To remove the jack, turn its shaft counterclockwise and pull the jack out of the storage bracket.
Trailer Towing: 5, 11, 13 Towing Your Vehicle (recreational towing): 13 EMERGENCY SERVICE WARNING Jacking Instructions 4) Block the front and rear of the wheel diagonally opposite of the wheel being lifted. 5) Place the spare wheel near the wheel being lifted as shown in the illustration in case that the jack slips. The jack should be used only to change wheels. It is important to read the jacking instructions in this section before attempting to use the jack.
Towing Your Vehicle (recreational towing): 13 EMERGENCY SERVICE Front wheel WARNING front 80J085 6) Position the jack at an angle as shown in the illustration and raise the jack by turning the jack handle clockwise until the jack-head groove fits around the jacking bar beneath the vehicle body. 7) Continue to raise the jack slowly and smoothly until the tire clears the ground. Do not raise the vehicle more than necessary. • Use the jack only to change wheels on level, hard ground.
Towing Your Vehicle (recreational towing): 13 EMERGENCY SERVICE Changing Wheels Full Wheel Cover (if equipped) To change a wheel, use the following procedure: 1) Remove the jack, tools and spare wheel from the vehicle. 2) Loosen, but do not remove the wheel nuts. 3) Jack up the vehicle (follow the jacking instructions in this section). EXAMPLE WARNING • Be sure to shift into “P” (Park) in CVT, or shift into “R” (Reverse) in manual transaxle when you jack up the vehicle.
EMERGENCY SERVICE Jump Starting Instructions WARNING • Never attempt to jump start your vehicle if the battery appears to be frozen. Batteries in this condition may explode or rupture if jump starting is attempted. • When making jumper cable connections, be certain that your hands and the jumper cables remain clear from pulleys, belts or fans. • Batteries produce flammable hydrogen gas. Keep flames and sparks away from the battery or an explosion may occur. Never smoke when working near the battery.
EMERGENCY SERVICE WARNING Never connect the jumper cable directly to the negative (–) terminal of the discharged battery, or an explosion may occur. 4) If the booster battery you are using is installed on another vehicle, start the engine of the vehicle with the booster battery. Run the engine at moderate speed. 5) Start the engine of the vehicle with the discharged battery. 6) Remove the jumper cables in the exact reverse order in which you connected them.
EMERGENCY SERVICE If the Engine is Flooded If the Engine Overheats If the engine is flooded with gasoline, it may be hard to start. If this happens, press the accelerator pedal all the way to the floor and hold it there while cranking the engine. (Do not operate the starter motor for more than 15 seconds). The engine could overheat temporarily under severe driving conditions. If the engine coolant temperature gauge indicates overheating during driving: 1) Turn off the air conditioner, if equipped.
EMERGENCY SERVICE 65D614 WARNING • It is hazardous to remove the radiator cap when the water temperature is high, because scalding fluid and steam may be blown out under pressure. The cap should only be taken off when the coolant temperature has lowered. • To prevent personal injury, keep hands, tools and clothing away from the engine cooling fan and airconditioner fan (if equipped). These electric fans can automatically turn on without warning.
EMERGENCY SERVICE MEMO 8-9 80J23-03E
APPEARANCE CARE APPEARANCE CARE Corrosion Prevention ......................................................... 9-1 Vehicle Cleaning .................................................................
APPEARANCE CARE Corrosion Prevention It is important to take good care of your vehicle to protect it from corrosion. vehicle which are not well ventilated to permit quick drying. Listed below are instructions for how to maintain your vehicle to prevent corrosion. Please read and follow these instructions carefully. For washing instructions, refer to the “Vehicle Cleaning” section.
Maintenance Schedule: 1, 2, 3, 4, 5, 6, 9, 10 APPEARANCE CARE Keep passenger and cargo compartments clean Moisture, dirt or mud can accumulate under the floor mats and may cause corrosion. Occasionally, check under these mats to ensure that this area is clean and dry. More frequent checks are necessary if the vehicle is used off road or in wet weather. Certain cargo such as chemicals, fertilizers, cleaners, salts, etc. are extremely corrosive by nature.
Periodic Maintenance Schedule: 1, 2, 3, 4, 5, 6, 9, 10 APPEARANCE CARE Vehicle Cleaning damp cloth to remove dirt and the soap solution. If some dirt still remains on the surface, repeat this procedure. Fabric upholstery Remove loose dirt with a vacuum cleaner. Using a mild soap solution, rub stained areas with a clean damp cloth. To remove soap, rub the areas again with a cloth dampened with water. Repeat this until the stain is removed, or use a commercial fabric cleaner for tougher stains.
Periodic Maintenance Schedule: 1, 2, 3, 4, 5, 6, 9, 10 APPEARANCE CARE Washing WARNING • Never attempt to wash and wax your vehicle with the engine running. • When cleaning the underside of the body and fender, where there may be sharp-edged parts, you should wear gloves and a long-sleeved shirt to protect your hands and arms from being cut. • After washing your vehicle, carefully test the brakes before driving to make sure they have maintained their normal effectiveness.
Maintenance Recommended under Severe Driving Conditions: 1, 2, 3, 4, 5, 6, 9, 10 APPEARANCE CARE Waxing 60B211S After washing the vehicle, waxing and polishing are recommended to further protect and beautify the paint. • Only use waxes and polishes of good quality. • When using waxes and polishes, observe the precautions specified by the manufacturers.
GENERAL INFORMATION GENERAL INFORMATION Identification Numbers ....................................................... 10-1 Safety Certification Label ................................................... 10-2 Emission Compliance Label (for U.S.A.) ........................... 10-2 Warranties ............................................................................ 10-2 On-Board Vehicle Computers and Event Data Recorders ............................................................................
Jacking Instructions: 5 GENERAL INFORMATION Identification Numbers The Vehicle Identification Number (VIN) may be found in the location shown in the above illustrations. This number is used to register the vehicle. It is also used to assist your dealer when ordering parts or referring to special service information. Vehicle Identification Number EXAMPLE (for some vehicles) Engine Serial Number 60G128 80JC090 The engine serial number is stamped on the cylinder block as shown in the above illustration.
Jacking Instructions: 5 GENERAL INFORMATION Safety Certification Label Emission Compliance Label (for U.S.A.) EXAMPLE Warranties The warranties covering your vehicle are explained in a separate New Vehicle Warranty Information booklet given to you at the time of sale. Please read this booklet carefully so you can understand your rights and responsibilities. For U.S.A.
Jacking Instructions: 5 GENERAL INFORMATION On-Board Vehicle Computers and Event Data Recorders Your vehicle is equipped with on-board computer systems which monitor and control several aspects of vehicle performance, including the following: • Emission-related components and engine parameters such as engine speed and throttle position are monitored to provide emissions control and to provide optimum fuel economy.
Jacking Instructions: 5 Jump Starting Instructions: 7 GENERAL INFORMATION Reporting Safety Defects If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying American Suzuki Motor Corp.
Jump Starting Instructions: 7 Towing a Disabled Vehicle: 6 GENERAL INFORMATION MEMO 10-5 80J23-03E
Fuses and Protected Circuits: 7 FUSES AND PROTECTED CIRCUITS FUSES AND PROTECTED CIRCUITS (4) (5) (6) (7) (8) (1) (2) (3) (12) (13) (14) (15) (20) (21) (22) (23) (24) (25) (9) (10) (11) (16) (17) (18) (19) (30) (26) (27) (29) (28) 80J101 PROTECTED CIRCUIT COLOR/SIZE (AMPS) MAIN FUSE BOX (1) BLACK (80) All electric load (2) RED (50) Power window, Ignition, Wiper, Starter (3) RED (50) Tail light, Rear defogger, Door lock, Hazard/Horn, Dome (4) – Blank (5) – Blank (6) BLUE (1
Fuses and Protected Circuits: 7 FUSES AND PROTECTED CIRCUITS (4) (5) (6) (7) (8) (1) (2) (3) (12) (13) (14) (15) (20) (21) (22) (23) (24) (25) (9) (10) (11) (16) (17) (18) (19) (30) (26) (27) (29) (28) 80J101 PROTECTED CIRCUIT COLOR/SIZE (AMPS) (11) MAIN FUSE BOX PINK (30) Radiator fan fuse (12) PINK (30) ABS solenoid fuse (13) PINK (30) Starting motor fuse (14) RED (50) Ignition switch fuse (15) PINK (30) Blower fan fuse (16) YELLOW (20) Air compressor fuse (17) BLUE (1
Fuses and Protected Circuits: 7 FUSES AND PROTECTED CIRCUITS (4) (5) (6) (7) (8) (1) (2) (3) (12) (13) (14) (15) (20) (21) (22) (23) (24) (25) (9) (10) (11) (16) (17) (18) (19) (30) (26) (27) (29) (28) 80J101 PROTECTED CIRCUIT COLOR/SIZE (AMPS) MAIN FUSE BOX (21) – Air compressor relay (22) – Fuel pump relay (23) – Condensor fan relay (24) – Front fog light relay (25) – Throttle motor relay (26) – FI MAIN relay (27) – Starting motor relay (28) – Radiator fan relay (
Fuses and Protected Circuits: 7 FUSES AND PROTECTED CIRCUITS SX4 (1) (2) (3) (4) (5) (6) (7) (8) (9) (10) (11) (12) (13) (14) (15) (16) (17) (18) (19) (20) (21) (22) (23) 80J053 COLOR/SIZE (AMPS) (1) FUSE BOX BLUE (15) FUSE NAME RR WIP PROTECTED CIRCUIT Rear wiper (2) BLUE (15) IG COIL Ignition coil (3) RED (10) BACK Back-up light (4) RED (10) MTR Meter (5) BLUE (15) ACC Accessory (6) BLUE (15) ACC2 Accessory 2 (7) PINK (30) P/W Power window (8) GREEN (30) WIP Wiper (
FUSES AND PROTECTED CIRCUITS (1) (2) (3) (4) (5) (6) (7) (8) (9) (10) (11) (12) (13) (14) (15) (16) (17) (18) (19) (20) (21) (22) (23) 80J053 FUSE NAME COLOR/SIZE (AMPS) (12) FUSE BOX BLUE (15) 4WD PROTECTED CIRCUIT 4WD (13) RED (10) STOP Stop light (14) YELLOW (20) D/L Door lock (15) RED (10) RR FOG Rear fog light (16) RED (10) ST SIG ST SIG (17) BLUE (15) S/H Seat heater (18) RED (10) IG2 SIG IG2 SIG (19) RED (10) TAIL Tail light (20) BLUE (15) DOME Dome (21) G
FUSES AND PROTECTED CIRCUITS SX4 SEDAN (21) (24) (7) (1) (2) (3) (4) (5) (6) (8) (9) (10) (11) (12) (13) (14) (15) (16) (17) (18) (19) (20) (22) (23) 80JC003 FUSE NAME COLOR/SIZE (AMPS) (1) FUSE BOX BLUE (15) RR WIP PROTECTED CIRCUIT Rear wiper (2) BLUE (15) IG COIL Ignition coil (3) RED (10) BACK Back-up light (4) RED (10) MTR Meter (5) BLUE (15) ACC Accessory (6) BLUE (15) ACC2 Accessory 2 (7) PINK (30) P/W Power window (8) GREEN (30) WIP Wiper (9) RED (10) IG1 SI
FUSES AND PROTECTED CIRCUITS (21) (24) (7) (1) (2) (3) (4) (5) (6) (8) (9) (10) (11) (12) (13) (14) (15) (16) (17) (18) (19) (20) (22) (23) 80JC003 FUSE NAME COLOR/SIZE (AMPS) FUSE BOX PROTECTED CIRCUIT (13) RED (10) STOP Stop light (14) YELLOW (20) D/L Door lock (15) RED (10) RR FOG Rear fog light (16) RED (10) ST SIG ST SIG (17) BLUE (15) S/H Seat heater (18) RED (10) IG2 SIG IG2 SIG (19) RED (10) TAIL Tail light (20) BLUE (15) DOME Dome (21) GREEN (30) RR DEF
FUSES AND PROTECTED CIRCUITS MEMO 11-8 80J23-03E
Specifications: 1, 2, 5, 6, 7, 10, 11 SPECIFICATIONS SPECIFICATIONS NOTE: Specifications are subject to change without notice. ITEM: Dimensions Overall length Overall width Overall height Wheelbase Track Ground clearance M/T: Manual transaxle CVT: Continuously variable transaxle UNIT: mm (in.) 195 tire 205 tire Front Rear 195 tire 205 tire 2WD: 2-wheel drive i-AWD: intelligent All Wheel Drive SX4 4115 – 4135 (162.0 – 162.8) 1730 – 1755 (68.1 – 69.1) 1575 (62.0) 1605 (63.2) 2500 (98.4) 1500 (59.
Specifications: 1, 2, 5, 6, 7, 10, 11 SPECIFICATIONS ITEM: Engine Type J20B (16V DOHC) Number of cylinders 4 Bore 84.0 mm (3.31 in.) Stroke 90.0 mm (3.54 in.) Piston displacement 1995 cm3 (1995cc, 121.7 cu.in) Compression ratio 10.2 : 1 ITEM: Electrical Ignition timing 3° – 17° B.T.D.C. at idle speed Standard spark plug NGK SILFR5A11 Battery DELKOR 24-700 12V Fuses See “INSPECTION AND MAINTENANCE” and “FUSES AND PROTECTED CIRCUITS” sections.
Specifications: 1, 2, 5, 6, 7, 10, 11 SPECIFICATIONS ITEM: Light Headlight Front fog light Front turn signal light Rear turn signal light Position light Brake/tail light License plate light Reversing light Dome light Luggage compartment light Spot light High mount stop light Side marker light SX4 SX4 SEDAN WATTAGE 12V 65/55W 12V 55W 12V 21W 12V 21W 12V 5W 12V 21/5W 12V 5W 12V 21W 12V 10W 12V 5W 12V 8W 12V 5W 12V18W 12V 5W BULB No.
Specifications: 1, 2, 5, 6, 7, 10, 11 SPECIFICATIONS ITEM: Wheel Tire size, front and rear SX4 P195/65R15, P205/60R16, P205/50R17 SX4 SEDAN P195/65R15, P205/50R17 Tire pressure For the specified tire pressure, see the Tire Information Label located on the driver’s door lock pillar. ITEM: Steering Toe IN 1.0 ± 1.0 mm (0.0393 ± 0.0393 in.
INDEX INDEX “CRUISE” Indicator Light.................................................... 2-66 “ESP OFF” Indicator Light......................................... 2-63, 3-25 “ESP” (Electronic Stability Program) Warning Light ....... 2-63 “ESP” Warning Light........................................................... 3-25 “SET” Indicator Light .......................................................... 2-66 Brake Assist System............................................................3-21 Brake Fluid.........
INDEX Drive Belt .............................................................................. 7-11 Driver’s Seat Belt Reminder Light...................................... 2-64 Driving on Hills ...................................................................... 4-3 Driving on Slippery Roads.................................................... 4-4 Driving range........................................................................ 2-72 E Electronic Stability Program (ESP®) ..............................
INDEX If Your Vehicle Gets Stuck .................................................... 4-4 Ignition Key Reminder........................................................... 2-1 Ignition Switch ....................................................................... 3-2 Illumination control setting................................................. 2-74 Illumination Indicator Light................................................. 2-67 Improving Fuel Economy......................................................
INDEX Periodic Maintenance Schedule........................................... 7-3 Power Door Locking System ................................................ 2-2 Power Mirror Control........................................................... 2-20 Power Steering..................................................................... 7-24 Power Steering Fluid ........................................................... 7-24 Power Window Controls .....................................................
INDEX Towing a Disabled Vehicle.................................................... 8-6 Towing Your Vehicle (recreational towing) ......................... 6-2 Traction Control System ..................................................... 3-24 Trailer Towing ........................................................................ 6-2 Transaxle selector position indicator ................................ 2-73 Trip meter .............................................................................
INDEX MEMO 13-6 80J23-03E
Prepared by June, 2009 Part No.