Installation Instructions

SS-00037
Cut Out Area
El Área Cortado
Masking Tape
La Cinta Adhesiva
Protectora
Drop in side:
1. Select the drop-in kitchen sink
template that applies to the model
sink you are installing. Cut out the
inside of the template and discard the
cutout portion. Locate the template
front to rear and right to left on
the countertop so the bowl will not
interfere with the cabinets below.
Attach the template to the countertop
with masking tape and draw a pencil
line around the inside of the template.
Discard the template.
Or
Invert sink and position onto the
countertop.Locate sink front to rear
and right to left so the bowl will not
interfere with the cabinets below.
Trace a pencil line around the outside
edge of the sink and remove the sink
from the countertop. Measure in 3/8”
(10mm) from the initial sink outline
and draw a second line inside the
rst. Draw a 1-1/2” radius at each
corner. The second interior line will be
your cut out line.
El lado de sobreponer:
1. Selecione la plantilla de la tarja de
cocina de sobreponer que aplica
al modelo que se está instalando.
Corte la parte interior de la plantilla
y deshágase de la parte cortada.
Ubique la platilla de frente a atrás
y de derecha a izquierda en el
mostrador para que la tarja no
inter era los armarios de abajo.
Amarre la plantilla al mostrador con
la cinta adhesiva protectora y dibuje
una línea con lápiz por el interior de
la plantilla. Deshágase de la parte
cortada.
O
Invierta la tarja de cocina y colóquela
en el mostrador. Ubique la tarja de
cocina de frente para atrás para que
no inter era los armarios de abajo.
Dibuje una línea con lápiz alrededor
del borde exterior de la tarja y quite
la tarja del mostrador. Mida desde
el interior 3/8” del contorno inicial y
dibuje una segunda línea dentro de
la primera. Dibuje un radio de 1-1/2”
en cada esquina. La segunda línea
interior será la línea para cortar.
SS-00038
Drill Starter Hole
Inside Of Cutout Line
Taladre Un Agujero
Para Comenzar
Dentro De La
Línea Para Cortar
2. Drill starter hole inside of cutout line.
This procedure should be performed
by a professional fabricator.
2. Taladre un agujero para comenzar
dentro de la línea para cortar.
Solo un fabricante profesional debe
hacer este procedimiento.
SS-00039
Cut Inside Of Line
Corte Por Dentro
De Línea
3. Using a saber saw, cut inside of
cutout line. Trial t sink to check
proper t.
3. Empleando una sierra sable, corte
por dentro de la línea para cortar.
Haga la prueba si cabe con la tarja.
SS-00040
NOTE:
Drill Starter Hole From Bottom
Finish Drilling Hole From Top
NOTE:
Taladre el Agujero Incial al
Reverso Termine Taladrando el
Agujero de la Superficie
4. Identify fixture hole locations. Drill
a starter hole from reverse side.
Working from the top side as
illustrated, position a hole saw on
the starter hole and drill to complete
the fixture hole. To cool the hole saw
and sink surface, a light application
of water, periodically, is necessary.
Attach faucet, drain, and accessories
according to manufacturer’s
instructions.
4. Identifique las situaciones de los
agujeros de la instalación. Taladre
un agujero inicial al reverso.
Trabajando del lado superior como
ilustrado, coloque una sierra de
agujero encima del agujero inicial
y taladre para completer el agujero
de la instalación. Para refrigerar la
sierra de agujero y la superficie de
la tarja, se necesita una aplicación
ligera de agua, de vez en cuando.
Sujete el grifo, el desagüe y los
accesorios según las instrucciones
del fabricante.
SS-00041
Caulk
Calafateo
5. Insert the sink clips into the slots
of each sink boss. Apply a bead of
caulk (not included) to the underside
of the sink flange. For final fit, make
sure each sink clip is pulled back as
illustrated. Position the sink into the
countertop opening.
5. Meta las grapas de la tarja en las
ranuras de cada tarja principal.
Aplique una gotita de calafateo
(no incluído) a la parte inferior del
reborde. Por el cabe final, asegure
que se retire cada grapa de la tarja
como está ilustrado. Coloque la tarja
en la apertura del mostrador.
SS-00042
6. Secure the sink by pivoting the sink
clips into the position illustrated and
tighten screws in the front, then
tighten rear and side screws.
6. Afiance la tarja para hacer girar las
grapas como la posición ilustrada y
apriete los tornillos enfrente. Luego,
apriete los tornillos de atrás y de los
lados.
Tools Required:
• Ruler/Tape Measure
• Masking Tape
• Caulk
• Drill
• Safety Glasses
• Screwdriver
• 1 -1/4” Hole Saw
• Saber Saw (if counter top cutout is
required)
Visit swanstone.com
for care & cleaning instructions
Herramientas Necesarias:
• Regla/Cinta Métrica
• Cinta Adhesiva Protectora
• Calafateo
• Taladro
• Lentes de Seguridad
• Destornillador
• Sierra de Agujos de 1 -1/4”
Sierra Sable (si se requiere recorte de
la superficie del mostrador)
32-1/4” (82 cm)
The Swan Corporation — Swanstone
www.swanstone.com
800-325-7008 Form #1005-01
3322
Sink template for:
Drop-In Kitchen Sink Installation Instructions and Templates
Las Instrucciones y Plantillas de Instalación de las Tarjas de Cocina de
Sobreponer
This template is for installation only of models:
QMDB-3322 QMED-3322
Este plantilla es para la instalación del tipo fijado abajo solamente de los modelos:
QMDB-3322 QMED-3322
21-1/4 (54 cm)
NOTICE
This sink is primarily intended for drop-in applications, however it can be
under-mounted, at the customers own risk. The included 3322 template is ONLY
used for the drop-in application.
The pre-drilled holes, in the faucet deck of the sink, are used only for drop-in applications.
For under-mount applications, these pre-drilled holes do not need to align with the desired
location of the faucet.
For under-mount applications, locate and mark the new holes on the countertop, according
to the faucet manufacturer’s instructions. Drill the new holes through the countertop and
the faucet deck of the drop-in sink. Again, it is not necessary for new holes to align with
the existing holes.

Summary of content (2 pages)