Communications Professional Security Camera Installation Guide

3
1.
2.
3.
4.
5.
Once you have chosen the best position for the camera, switch the
power to the camera off, and unplug the power lead from the
camera.
When mounting the Bulldog Camera to your ceiling or wall, please
ensure that you rotate the camera so that at the top of the camera
lens is ‘up’, otherwise you will find that your pictures are displayed
upside down. (see diagram)
Hold the camera base in the position you wish to fix it, and mark the
holes with an appropriate pen or pencil. Once this is done, remove
the stand and drill a hole with the appropriate drill bit for the material
you are mounting your camera to and the screws you are using.
Run the camera cable back to the TV/VCR, any holes that you drill
need to be at least 14mm in diameter to allow the connectors to
pass through.
Reconnect the power lead to the camera and switch the camera
power back on.
Step 1:
Step 2: BNC Female BNC Male Extension Cable
BNC Male
Step 3: Power Connector power adaptor
Step 4: power adaptor
Step 5: A/V TV BNC to RCA adaptor
BNC Connector Extension Cable 3 RCA Socket
TV VCR TV AV
VCR VCR A/V
Input TV
VCR
Note:
Note: instructions VCR TV
A/V inputs.
At the end of your Bulldog Camera cable you will find two plugs:
•Silver ( )
•Black ( )
Plug the ( ) into the ( ) of the ( ) and turn
the outer ring to lock the connectors. Plug the other ( ) at the opposite end of
the extension cable into a BNC connector on your security device (usually located at the back
of your DVR or Quad Switcher).
Connect the ( ) at the end of the ( ) in to your Bulldog
Camera’s DC Jack ( ), or the 10m extension cable’s DC Jack ( ) if you are using it. Use
whichever is located near the most convenient power outlet
Plug the ( ) into the mains power point on your wall and switch on if
required.
If you have an with RCA sockets you will need to use the ( )
in between the ( ) on the ( ) and the of
your or . You will then need to switch the to the channel to view the camera.
To connect the Bulldog Camera to your , you will need to turn the to the
selection and turn your onto the channel you would normally use to view a tape or
movie on your .
The Bulldog Camera will automatically change to a black & white image using the Infra-Red
LEDs when available light is too low to support a clear colour picture.
Please read the for your or for more information on using their
Video BNC Female
DC Power Jack
1b 3b 3
3d
2a 2
1a 3c
2
3d
4
Mounting the camera on your wall or ceiling
How to connect the Bulldog Camera to your monitoring device
Bulldog kameraet er designet til bruk for DVR, VCR, sikkerhetsmonitorer, TV, eller pc med et videokort.
Kameraet kan brukes innendørs eller utendørs. Bulldog kameraet har mange muligheter f.eks. å se hvem
som er ved døren, overvåk din bil, båt, forretning eller bruk kameraet til å overvåk dine barns
lekeområde.
1. Bulldog kameraet med holder og kabel.
2. 12Volt DC strøm forsyning (denne kan variere fra land til land)
3. 10m strøm og video forlengerkabel.
4. BNC (Hun kontakt) til RCA (Han kontakt) adapter.
BNC (hun kontakt)
DVR, TV, VCR eller monitor
OUT
IN
VIDEO
VIDEO
AUDIO
AUDIO
VIDEO
INNGANG
Ditt Bulldog kamera er designet til å overføre høykvalitets fargebilde til din sikkerhetsenhet eller TV, og det
fungere med vanlig strøm. For å hjelpe deg gjennom oppsettet av Bulldog kameraet har vi delt det inn i
trinn, og nummerert hver komponent i medfølgende diagram.
DC kontakt
DC STRØM TILKOBLING
3c
2a
1b
KAMERA
1
STRØMFORSYNING
2
2
4
3
DC kontakt
1a
UTVIDELSESKABEL
3
BNC (han kontakt)
3b
BNC (han kontakt)
3d
DC kontakt
3a
18
Installasjon instruksjoner
Innhold og dele- identifikasjon
Hvordan man kobler Bulldog kamera til overvåkningsenheten