™ Advanced security made easy ™ Wireless Alarm System Swann Technical Support SW347-WA2 All Countries E-mail: tech@swannsecurity.com Telephone Helpdesk USA toll free 1-800-627-2799 (Su, 2pm-10pm US PT) (M-Th, 6am-10pm US PT) (F 6am-2pm US PT) USA Exchange & Repairs 1-800-627-2799 (Option 1) (M-F, 9am-5pm US PT) AUSTRALIA toll free 1300 138 324 (M 9am-5pm AUS ET) (Tu-F 1am-5pm AUS ET) (Sa 1am-9am AUS ET) NEW ZEALAND toll free 0800 479 266 UK 0203 027 0979 See http://www.worldtimeserver.
Before You Begin FCC Verification: NOTE: This equipment has been tested and found to comply with the limits for Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Technical Specifications Power Requirements Wireless Frequency Sensitivity Siren Volume Alarm Duration Operating Temperature Keypad Control Unit 9V DC (supplied adapter) 433 MHz >-110dB > 110dB 0 ~ 20 minutes -10C° ~ +40C° Remote Control Battery Requirements 1 x 27A (12V DC) Power Consumption (Standby) 0mA Power Consumption (Operating) <10mA Transmission Frequency 433 MHz Transmission Range Up to 262ft/80m line of sight Typical Transmission Range 65ft/20m Operating Temperature -10C° ~ +40C° Passive Infrar
IMPORTANT - Read Before Installing For your safety and the safety of others, and to ensure that you get the most out of the Home Wireless Alarm System, please read and adhere to these guidelines. • Do not expose any part of the Wireless Alarm System to any sudden shocks (such as being dropped or struck).
Troubleshooting About the Wireless Alarm System Problem: I keep getting false alarms! Solution: There are a few possible reasons why this might be occurring. 1. Check that there are no strong magnetic fields around your Window/Door Sensor(s). Things like televisions, computers, microwaves and (of course) magnets of any kind will interfere with the proper operation of the Window/ Door Sensor and could lead to false alarms. 2.
The Keypad Alarm Control Unit Batteries The Keypad Alarm Control Unit is the heart of the Wireless Alarm System. It is responsible for monitoring the various sensors throughout your home, and for triggering the alarm signal when one of them reports a disturbance. As such, it is the single most important part of the Wireless Alarm System, and (with the possible exception of the remote controls) the part of the system that you will use most often.
Arming and Disarming the System There are two ways to arm the system, using either the Keypad Alarm Control Unit or the remote. Arming the system via the remote control is quick, requiring only a couple of buttons be pushed. Arming the system via the Keypad Alarm Control Unit is likewise quick and easy, but for security purposes, you’ll need your passcode to gain access to the system.
The PIR motion sensor PIR Motion Sensor The Passive InfraRed (PIR) Motion Sensor will, under typical conditions, detect a human being moving around within approximately thirty feet (about 10m) from the sensor. This is an average value, as the actual detection range is between 16ft/5m and 50ft/15m. As the performance of the sensor is determined primarily by environmental conditions, no guarantees can be offered regarding the detection range.
Alarm Zones and Modes Modes: Placing the PIR motion sensors The Wireless Alarm System has two main modes of operation, the Home Mode and Out Mode. These zones do not refer to where the sensors are placed, but where you are at any given time. The PIR motion sensors have an effective range of between 16ft/5m and 50ft/15m depending on the specific conditions of the environment. Typically, the sensor will have a longer range in colder conditions, or in evenly heated environments.
The Remote Control Your Passcode & Alarm Duration Your wireless alarm system comes with a keychain-sized remote control. In many ways, the remote control is the most powerful and important device in your security system – essentially, it is the electronic key. Treat it like you would any other key keeping it on your keychain typically helps. Using the remote control, you can arm and disarm the system (in either Home Mode or Out Mode) from anywhere in range of the wireless signal.
The Remote Control Your Passcode & Alarm Duration Your wireless alarm system comes with a keychain-sized remote control. In many ways, the remote control is the most powerful and important device in your security system – essentially, it is the electronic key. Treat it like you would any other key keeping it on your keychain typically helps. Using the remote control, you can arm and disarm the system (in either Home Mode or Out Mode) from anywhere in range of the wireless signal.
Alarm Zones and Modes Modes: Placing the PIR motion sensors The Wireless Alarm System has two main modes of operation, the Home Mode and Out Mode. These zones do not refer to where the sensors are placed, but where you are at any given time. The PIR motion sensors have an effective range of between 16ft/5m and 50ft/15m depending on the specific conditions of the environment. Typically, the sensor will have a longer range in colder conditions, or in evenly heated environments.
The PIR motion sensor PIR Motion Sensor The Passive InfraRed (PIR) Motion Sensor will, under typical conditions, detect a human being moving around within approximately thirty feet (about 10m) from the sensor. This is an average value, as the actual detection range is between 16ft/5m and 50ft/15m. As the performance of the sensor is determined primarily by environmental conditions, no guarantees can be offered regarding the detection range.
Arming and Disarming the System There are two ways to arm the system, using either the Keypad Alarm Control Unit or the remote. Arming the system via the remote control is quick, requiring only a couple of buttons be pushed. Arming the system via the Keypad Alarm Control Unit is likewise quick and easy, but for security purposes, you’ll need your passcode to gain access to the system.
The Keypad Alarm Control Unit Batteries The Keypad Alarm Control Unit is the heart of the Wireless Alarm System. It is responsible for monitoring the various sensors throughout your home, and for triggering the alarm signal when one of them reports a disturbance. As such, it is the single most important part of the Wireless Alarm System, and (with the possible exception of the remote controls) the part of the system that you will use most often.
Troubleshooting About the Wireless Alarm System Problem: I keep getting false alarms! Solution: There are a few possible reasons why this might be occurring. 1. Check that there are no strong magnetic fields around your Window/Door Sensor(s). Things like televisions, computers, microwaves and (of course) magnets of any kind will interfere with the proper operation of the Window/ Door Sensor and could lead to false alarms. 2.
IMPORTANT - Read Before Installing For your safety and the safety of others, and to ensure that you get the most out of the Home Wireless Alarm System, please read and adhere to these guidelines. • Do not expose any part of the Wireless Alarm System to any sudden shocks (such as being dropped or struck).
Technical Specifications Power Requirements Wireless Frequency Sensitivity Siren Volume Alarm Duration Operating Temperature Keypad Control Unit 9V DC (supplied adapter) 433 MHz >-110dB > 110dB 0 ~ 20 minutes -10C° ~ +40C° Remote Control Battery Requirements 1 x 27A (12V DC) Power Consumption (Standby) 0mA Power Consumption (Operating) <10mA Transmission Frequency 433 MHz Transmission Range Up to 262ft/80m line of sight Typical Transmission Range 65ft/20m Operating Temperature -10C° ~ +40C° Passive Infrar
Before You Begin FCC Verification: NOTE: This equipment has been tested and found to comply with the limits for Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
™ Advanced security made easy ™ Wireless Alarm System Swann Technical Support SW347-WA2 All Countries E-mail: tech@swannsecurity.com Telephone Helpdesk USA toll free 1-800-627-2799 (Su, 2pm-10pm US PT) (M-Th, 6am-10pm US PT) (F 6am-2pm US PT) USA Exchange & Repairs 1-800-627-2799 (Option 1) (M-F, 9am-5pm US PT) AUSTRALIA toll free 1300 138 324 (M 9am-5pm AUS ET) (Tu-F 1am-5pm AUS ET) (Sa 1am-9am AUS ET) NEW ZEALAND toll free 0800 479 266 UK 0203 027 0979 See http://www.worldtimeserver.