Installation Instructions
m Walls must be solid, plumb, and square within 1/8 inch of
true. Shim or trim the opening, as required. This kit has
been designed with some adjustability for minor alignment
problems.
m The mounting surface must be free of dirt, lm, waxes, or
any other residues.
m If you are installing a recessed accessory, cut the hole
after the panel is installed and fully supported by the wall.
Remember to position the accessory between the wall studs.
Caulking Tips
m Follow the instructions on the color match silicone sealant
tube
m When job is complete, inspect all caulked areas for gaps and
ll as needed.
m Clean up any excess silicone using denatured alcohol and a
clean cloth.
m Be very careful not to disturb caulk joints before they dry.
Wall Surface Preparation
Swan Corporation panels can be installed over a variety of
products. If you intend to apply the panels to any surface other
than those described, consult with a professional contractor.
Use the following sections when installing this product over:
m SHEETROCK/GREENBOARD/CEMENT BOARD/WOOD
m PLASTER
m CEMENT/CONCRETE
m OLD TILE
m WALLPAPER
m MASONITE
Sheetrock, Greenboard, Cement Board, or Wood
m Surface must be dry, smooth, and free of any dust, soap
scum, or any other contaminants
.
m To ensure proper adhesion of the panels, the wall surface
must be sealed with a water or oil-based primer/sealer
.
m After the primer/sealer is completely dry, complete the
installation following the instructions in this manual.
Plaster
Depending on the condition of the existing wall surface,
additional silicone may be required to ensure contact between
the substrate and the wall panel.
m Sand textured or swirled nishes smooth.
m Clean the wall surface with a damp cloth to remove any dust,
soap scum, or any other contaminants. The wall surface
must be dry and smooth.
m To ensure proper adhesion of the panels, the wall surface
must be sealed with a water or oil-based primer/sealer
.
m After the primer/sealer is completely dry, complete the
installation following the instructions in this manual.
Cement/Concrete
Depending on the condition (atness) of the existing wall
surface, additional silicone may be required to ensure contact
between the substrate and the wall panel.
m To ensure proper adhesion of the panels, the complete area
must be sealed with two coats of water or oil-based primer/
sealer.
m After the primer/sealer is completely dry, complete the
installation following the instructions in this manual.
Old Tile
Depending on the condition of the existing wall surface,
additional silicone may be required to ensure contact between
the substrate and the wall panel.
Old ceramic tiles, if solidly adhered, do not need to be
removed.All plastic tiles must be removed.
m Remove or reattach any loose ceramic tiles. Old tiles and
front edge ceramic tiles should be reset for appearance only.
m Remove any tile accessories attached to the walls.
m Remove the bottom row of tile and cut a ventilation gap in
the substrate.
m The tile surface must be dry, smooth, and free of any dust,
soap scum, or any other contaminants.
m Complete the installation following the instructions in this
manual.
m Note: If using a trim kit, old tiles may need to be removed to
allow a proper t.
Wallpaper
m All wallpaper must be removed from the area being covered.
Clean the wall surface to remove any dust, soap scum, or
any other contaminants. The wall surface must be dry and
smooth
.
m To ensure proper adhesion of the panels, the complete wall
surface must be sealed with two coats of water or oil-based
primer/sealer.
m After the primer/sealer is completely dry, complete the
installation following the instructions in this manual.
Masonite
1. Clean the wall surface to remove any dust, soap scum, or
any other contaminants. The wall surface must be dry and
smooth.
m To ensure proper adhesion of the panels, the wall surface
must be sealed with a water or oil-based primer/sealer.
m After the primer/sealer is completely dry, complete the
installation following the instructions in this manual.
IMPORTANT NOTICE
Swan 6 800-325-7008
General Information