Installation Guide

ManualsBrandsSwanstone ManualsShower Wall PartsTC06072TR.059

Model TC-6072-TR

(for bathtub installation)

Model TC-105-TR

(for shower installation)

Included in Kit:

TC-6072-TR

• Three molding pieces

3 3/4" wide x 105" high

• Four rosettes 4" x 4"

• One tube adhesive

• One tube color

coordinated caulk

TC-105-TR

• Four molding pieces

3 3/4" wide x 105" high

• Four rosettes 4" x 4"

• one tube adhesive

• one tube color

coordinated caulk

Molding and Rosettes

Installation Care and Cleaning

Before you start

The Swanstone Molding and

Rosettes may be installed over

any solid surface. This product

makes a beautiful casing

around doors, windows, and

mirrors. For the purpose of

instruction, this procedure will

address an application over a

bathtub or shower floor using a

Swanstone wall panel. It may

also be installed by itself or

with other wall materials.

THRESHOLD ROSETTES

1. Choose the rosette design

pattern that you wish and

apply a glob of adhesive to the

opposite side of the design

that you select. The most

desirable placement will line

up the front edge of the rosette

with the front edge of the bath-

tub or shower floor threshold.

Follow this procedure for the

application of both threshold

rosettes.

VERTICAL MOLDING &

ROSETTES

Select two of the molding

pieces. Measure and cut to fit

the vertical application.

Remember that a rosette piece

will be positioned above the

molding piece. Take this into

consideration prior to measur-

ing and cutting.

TRIAL FIT

Check with a level. Note that the molding pieces are slightly nar-

rower than the rosettes. Therefore, the molding pieces should be

centered over the bathtub or shower floor threshold rosette. Mark

the location of the vertical molding with "tick" marks. These

"tick" marks will be used for final fit. Temporarily secure the mold-

ing to the wall with masking tape. Select the molding design you

wish and the rosette design that is consistent with the threshold

rosettes, and trial fit and tape into position above the vertical

molding pieces.

If you have selected a

Swanstone solid surface wall

panel to complement this

application, install the molding

and rosettes first. Prior to

installing the moldings and

rosettes, keep in mind the size

limits of the wall that you are

installing. After you have

installed the molding and

rosettes, follow the installation

instructions provided in the

wall kit.

When installing the side walls,

be aware that it will be neces-

sary to "notch" the side wall

panels around the ro s e t t e s .

Take these measurements into

consideration prior to final fit

of the side wall panels.

Molding

Side A

Fluted

Rosette

Side B

Butterfly

Rosette

Side A

Circle

Rosette

Side B

Star

Tools Required:

Tools needed are a saber saw,

drill, ruler, level, masking tape,

and caulking gun.

Summary of content (2 pages)

PAGE 1
Molding and Rosettes Installation Care and Cleaning Model TC-6072-TR (for bathtub installation) Model TC-105-TR (for shower installation) Molding Side A Fluted Rosette Side A Circle Rosette Side B Butterfly Included in Kit: TC-6072-TR • Three molding pieces 3 3/4" wide x 105" high • Four rosettes 4" x 4" • One tube adhesive • One tube color coordinated caulk When installing the side walls, be aware that it will be necessary to "notch" the side wall panels around the rosettes.
PAGE 2
Molding and Rosette Care Cleaning and Installation (continued) BACK WALL MOLDING SIDE WALLS – HORIZONTAL MOLDING 3. Transfer the width measurement of the back wall onto one of the molding pieces. Trim as needed. Choose the molding design pattern that is consistent with the vertical strips and apply "globs" of adhesive following the pattern illustrated. Final fit by setting into position. Note that the horizontal wall molding will also be centered on the rosettes atop the vertical moldings.