Safety Instructions

ManualsBrandsSwidget ManualsSmart HomeZ-Wave Control

Less than 1 sec No change None

1 - 5 sec Green ON OFF Manual Outlet Toggle

5 - 10 sec No change None

10 - 15 sec Blue ON Network ADD/REMOVE Mode

15 - 20 sec OFF None

20 - 25 sec Red ON Device Local Reset (Factory Reset)

More than 25 sec No change None - button press ignored

LED COLOR CODE

DESCRIPTION

Green Blue Red

ON OFF OFF Outlet ON, Radio Connected

OFF OFF OFF Outlet OFF, Radio Connected

LED COLOR CODE

DESCRIPTION

Green Blue Red

OFF ON OFF

Entered ADD/REMOVE Mode

Mode enabled

OFF Flash OFF Connecting to network

OFF

Off On

Flash

ADD/REMOVE successful

Blue to OFF when complete

Flash OFF OFF

POWER READING ZERO

Green ash for >60 sec then off

OFF OFF Flash

ADD/REMOVE failed after 60 sec

Red ashes for 5 sec

LED COLOR CODE

DESCRIPTION

Green Blue Red

Cycle Cycle Cycle

DEVICE LOCAL RESET is in

progress

OFF OFF OFF

Network Connection FAIL. Red

will ash

FEATURES:

• One controlled AC receptacle (marked “CONTROLLED”)

Remote ON/OFF control via external Z-Wave controller/hub

• Requires 3rd party Z-Wave Controller/Hub

• Manual ON/OFF control via front panel push button

• One always ON AC receptacle

• Independent power monitoring of both AC receptacles

• Swidget Z-Wave Device detected as:

• Meter (always ON receptacle)

• Switch + Meter “CONTROLLED” receptacle

Push to

Install

Side Latches

SAVE THESE INSTRUCTIONS

INSTALLATION:

1. TO AVOID SHOCK OR DEATH, IT IS RECOMMENDED TO TURN OFF POWER AT CIRCUIT BREAKER OR FUSE AND TEST THAT

THE POWER IS OFF BEFORE INSTALLING OR REMOVING INSERT

2. This device is to be installed in a Swidget outlet ONLY.

3. Orient the Insert to line up with the pins in the Outlet cavity. NOTE: alignment pins will prevent incorrect installation.

4. Push Insert into the Outlet cavity until the two side latches engage.

5. Re-enable power to Outlet.

6. a. For a rst time installation or after Device Local Reset, the Insert requires network ADD pairing/joining (see below).

b. For Inserts being moved, the Insert will power up with the previous location settings. For any required adjustments, consult the

manual of the connecting Z-Wave controller/hub.

FCC COMPLIANCE STATEMENT:

This device complies with part 15 of the FCC and Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation.

FCC NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modications to this equipment. Such modications could void the user’s authority to operate the

equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against

harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions may cause harmful

interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception,

which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

Important note: To comply with the FCC RF exposure compliance requirements, no change to the antenna or the device is permitted. Any change to the antenna or the device could result in the device

exceeding the RF exposure requirements and void user’s authority to operate the device.

OPERATION:

MANUAL OUTLET SWITCHING - Works with radio connection only

1. Lightly press Insert push button and hold for 1-5 seconds then release. Outlet will toggle state.

Z-WAVE NETWORK ADD

1. Follow network ADD steps for your Z-Wave controller/hub.

2. IMPORTANT- Nothing plugged into either receptacle during NETWORK ADD as this will interfere with POWER READING ZERO opera-

tions.

3. Lightly press Insert push button and hold for 10-15 seconds then release (LED turns solid blue).

a. LED will ash blue to indicate ADD mode is enabled. No manual or external Z-Wave operations are possible during this activity.

b. LED will ash green to indicate POWER READING ZERO running. Process will take >60sec and will stop ashing when

done.

4. Insert will remain in ADD mode for up to 60sec. If successful, LED will be solid blue for 5 sec then return to the normal operational state.

IF FAILED to connect after 60sec, red LED will ash indicating no or failed network ADD. If necessary, consult your Z-Wave controller/hub

manual and retry.

Z-WAVE NETWORK REMOVE

1. Follow network REMOVE steps for your Z-Wave controller/hub.

2. Lightly press Insert push button and hold for 10-15 seconds then release. LED will ash blue to indicate REMOVE mode is enabled. No

manual or external Z-Wave operations are possible during this activity.

3. Insert will remain in REMOVE mode for up to 60 seconds. If successful, LED will be solid blue for 5 seconds then return to the normal oper-

ational state. IF FAILED to connect after 60sec, red LED will ash indicating no or failed network REMOVE. If necessary, consult your Z-Wave

controller/hub manual and retry.

Z-WAVE LOCAL DEVICE RESET (FACTORY RESET)- Should only be used when the original controller is inoperable or has been

replaced.

1. Lightly press Insert push button and hold for 20-25 seconds then release. LED will cycle green/blue/red until complete.

INSERT BUTTON ACTIONS LED INDICATOR CHART

DEVICE RESET MODE

DESCRIPTION:

The Swidget Congurable Smart Outlet with the Z-Wave Power Control Insert allows the user to control power to a receptacle (marked “CONTROLLED”) and monitor power (both receptacles independently)

for devices plugged into the Swidget outlet. Z-Wave is a standardized mesh network protocol used by many devices and hubs. Swidget certication to this standard means compatibility with other Z-Wave

certied devices or hubs. Please consult your Z-Wave controller/hub manufacturer for instructions on how to add a new Z-Wave device.This product can be operated in any Z-Wave network with other

Z-Wave certied devices from other manufacturers. All non-battery operated nodes within the network will act as repeaters regardless of vendor to increase reliability of the network.

MUST BE INSTALLED AND USED ONLY WITH AN APPROVED/CERTIFIED SWIDGET OUTLET. USE WITH ANY OTHER DEVICE IS PROHIBITED

AND WILL VOID THE WARRANTY.

WARNING AND CAUTIONS:

• WHILE NOT REQUIRED, IT IS RECOMMENDED TO AVOID ANY RISK OF SHOCK OR DEATH, TURN OFF POWER AT CIRCUIT BREAKER OR

FUSE AND TEST THAT THE POWER IS OFF BEFORE INSTALLING OR REMOVING ANY INSERT.

• Not for use to control medical or life support equipment.

• For INDOOR use only: 32-104F (0-40C).

• Do not use Z-Wave devices to control electric heaters or any other appliances which may present a hazardous condition due to unattended or

unintentional or automatic power on control.

• Double check any external Z-Wave programming for accuracy before using them.

• Insert can only be installed in one orientation. Rear alignment pins prevent incorrect installation. Do not forcibly install an Insert.

• For reference, the controlled Swidget receptacle is marked on the face as “CONTROLLED”.

• Do not exceed the load rating for the Swidget outlet:

• Resistive: 1800W

• Motor: 0.5HP

• Inductive: 8A@125VAC (PF0.4)

• Requires a certied Z-Wave hub for operation.

• This device complies with Z-Wave standard of open air, line of sight transmission. Actual performance in a home depends on the numbers of walls/

obstacles between the Insert and other Z-Wave devices/hubs.

• This device must be used in conjunction with an S2 Security Enabled Z-Wave Controller to fully utilize all implemented security functions.

• Use with Swidget Outlet Model Number R1015SWA.

Model No.: ZW000RWA

IMPORTANT SAFETY INSTRUCTIONS

Z-Wave Control

NETWORK ADD/REMOVE MODE

PROBLEMS or QUESTIONS:

If you have any problems with or questions about the Swidget Outlet

or Insert, contact our tech support team:

support@swidget.com

For the most up-to-date product support, accessories,

electronic (PDF) format manuals and more, visit

www.swidget.com.

For additional Z-Wave network technical information, see Swidget

Z-Wave Power Control Insert Technical Notes on the swidget

website.

No user serviceable parts in this unit.

If you have problems with the connecting hub, please consult the

manufacturer for the appropriate support

Summary of content (2 pages)

PAGE 1
IMPORTANT SAFETY INSTRUCTIONS Z-Wave Control Model No.: ZW000RWA MUST BE INSTALLED AND USED ONLY WITH AN APPROVED/CERTIFIED SWIDGET OUTLET. USE WITH ANY OTHER DEVICE IS PROHIBITED AND WILL VOID THE WARRANTY. WARNING AND CAUTIONS: • WHILE NOT REQUIRED, IT IS RECOMMENDED TO AVOID ANY RISK OF SHOCK OR DEATH, TURN OFF POWER AT CIRCUIT BREAKER OR FUSE AND TEST THAT THE POWER IS OFF BEFORE INSTALLING OR REMOVING ANY INSERT. • Not for use to control medical or life support equipment.
PAGE 2
CONSIGNES DE SÉCURITÉ IMPORTANTES Contrôle Z-Wave Model No.: ZW000RWA DOIT ÊTRE INSTALLÉ ET UTILISÉ UNIQUEMENT AVEC UNE PRISE SWIDGET AGRÉÉE/CERTIFIÉE. L’UTILISATION AVEC TOUT AUTRE APPAREIL EST INTERDITE ET ANNULE LA GARANTIE.