Users Manual
Table Of Contents
- 页 1
- 书签477E31AD 设备静音
- 书签7C146629 - 设备正常工作状态下,发射端短按按键1次, 绿灯闪烁 ,进入静音模式。再短按一次发射端, 设备恢复正常工作状态。
- 书签5376EC54 M1 无线麦克风系统
- 书签2E1AD9B6 - M1是一款基于2.4G技术设计的无线麦克风系统,是全球开放免许可证使用的频段,M1具有音质还原度高,抗干扰性强等特点, 为了避免信号衰减,无线系统应尽量接近演出区,并且与大的金属物、墙面、脚手架等物体至少保持1.5米的距离,并尽量保证 发射器与接收器之间有空旷的信号直射途径。演出前请仔细检查电池电量是否充足,避免因电量不足而无法使用,M1无线系统 适用于卡侬口的动圈麦克风,在使用前请确保设备能匹配并正常使用。
- 书签3ED373FE 产品参数
- 书签219BE1E7 使用频段: 2.4GHz ISM频段 Worldwide 传输范围 : 30米 接收灵敏度: <-110dBm@20dBSINAD 延迟 : < 5ms 信噪比: >85dB 频响范围: 20Hz-20KHz ,+1dB/-3dB
- 书签1948CFDE 动态范围: 102db 失真度: < 0.05% 满电工作时间: ≥5h (可充电锂电池) 外形尺寸: Tx:102*23*20mm Re:103*23*23mm 重量: 65g 颜色: 黑色
- 书签A86B3AFA 产品附件清单
- 书签A53FE3EB 发射端 X 1
- 书签CCD9A11C 接收端 X 1
- 书签1C91303E 双头USB充电线 X 1
- 书签EB24F220 说明书 X 1
- 书签068EF184 产品介绍说明
- 书签A8015EDF 按键
- 书签39454CEB 指示灯
- 书签45DDABCE 卡侬头
- 书签B9615599 设备充电
- 书签171C8B97 *设备配有双头的USB充电线, 可同时给发射端和接收端进行充电, 请选用5V 1A的充电器进行充电;
- 书签ED5E7B9C *设备使用的是聚合物锂电池,使用设 备前需先给设备进行充电;长时间不 使用,三个月给产品充电一次激活;
- 书签4861D10B *插入充电线后,电源指示灯红绿灯 常亮,表示充电故障,需要交给专 业的维修人员进行维修。
- 书签EB3627C7 5V 1A
- 书签8EA416A0 - 设备处于充电状态时,发射端和接收端的电源指示灯红灯常亮,当电量充满以后电源指示灯绿灯常亮。当电量处于满电状态下 又接入充电时,会启动电池保护,发射端和接收端的电源指示灯红灯常亮,20分钟后恢复绿灯常亮。
- 书签903E5CF5 >3个月
- 书签4DC7EFCE 充电故障:黄灯常亮
- 书签4EB6E9A4 设备电量检查
- 书签59CC7195 - 关机状态下电量检查: 双击按键两次,电量≥75%时,指示灯绿灯闪烁四次, 75%>电量≥50%时,指示灯绿灯闪烁3次, 50%>电量≥25%时,指示灯绿灯闪烁2次, 指示灯绿灯闪烁1次,25%>电量≥1%时, 指示灯绿灯闪烁1次。 - 开机状态下电量检查: 当电量低于20%时,指示灯红灯常亮,需要对设备进行充电。
- 书签016A196D 关机状态下
- 书签8EA3E098 开机状态下
- 书签13B4A3F4 双击按键
- 书签E00087E8 闪烁4次 电量≥75%
- 书签67A51EC1 闪烁3次 75%>电量≥50%
- 书签6E2A269A 闪烁2次 50%>电量≥25%
- 书签2FD514AB 闪烁1次 25%>电量≥1%
- 书签38E8AA40 红灯常亮 电量<20%
- 书签A29D0E38 设备开/关机
- 书签C103B593 - 开机:发射端与接收端关机状态下长按按键2秒, 指示灯绿色常亮,设备开机启动成功, 进入正常工作状态。 - 关机:发射端与接收端开机状态下长按按键2秒, 指示灯熄灭,关机成功。 *开机后发射端指示灯绿灯常亮,接收端指示灯绿灯闪烁,表示设备还未正常连接。
- 书签63C1FCA6 长按两秒开/关机
- 书签21EE47E8 设备配对
- 书签458C7DD7 * 如果设备开机后不能正常工作,并且发射端绿灯常亮,接收端绿灯闪烁,需要对设备重新进行配对。 - 设备重新配对:关机状态下,长按按键5秒,发射端与接收端 指示灯红绿灯交替闪烁,设备进行配对中,当设备配对 成功后指示灯绿灯常亮,设备进入工作状态。 * 设备配对时发射端与接收端请尽量靠近。如果设备配对不成功, 指示灯红绿交替闪烁持续2分钟后自动关机。
- 书签68F58F98 设备跳频
- 书签115D7EA4 * 当使用设备时周围有信号干扰导致设备无法正常工作,可对设备进行跳频。 - 设备跳频:双击发射端按键,发射端指示灯闪绿灯一次, 接收端指示灯闪绿灯一次,跳频成功。
- 书签33D38C74 Dynamic range: 102db Distortion: < 0.05% Full power working time: ≥ 5h \(rechargeable lithium battery\) Dimensions: TX: 102*23*20mm RE: 103*23*23mm Weight: 65g Colour: Black
- 书签868D0D9D Band used: 2.4GHz ISM band Worldwide Transmission range: 30 meters Acceptance sensitivity: <-110dBm@20dBSINAD Delay: < 5ms Signal to noise ratio: >85dB Frequency response range: 20Hz-20KHz, +1dB/-3dB
- 书签392BF60C Product Specification
- 书签4B364840 M1 wireless microphone system
- 书签59BE78FE - M1 is a wireless microphone system based on 2.4GHz technology. It uses the worldwide open license-free frequency band. M1 has the characteristics of high sound quality reduction and strong anti-interference. In order to avoid signal attenuation, the wireless system should be close to the performance area as possible, and at least 1.5 meters away from large metal objects, walls, scaffolding and other objects, and try to ensure that there is an open direct signal path between the transmitter and receiver. Please carefully check whether the battery power is sufficient before use, avoid being unusable due to low battery. The M1 wireless system is suitable for dynamic microphones of the XLR port. Before use, please ensure that the device can be matched and used normally.
- 书签6C2AD183 Package contents
- 书签9E8E528E Transmitter X 1
- 书签23381E33 Receiver X 1
- 书签B5777CF3 USB charging cable X 1
- 书签3F4A9B79 User manual X 1
- 书签36B55988 Product Introdution
- 书签113B2B5C Button
- 书签A6C5DF45 LED indicator
- 书签F2BB961F XLR interface
- 书签0CFFEC70 USB charging port
- 书签C86773C6 Check battery capacity
- 书签8A3C1FAD In power off state
- 书签3671F32D Double click the button
- 书签B8BEA963 Green light flashes 4 times. power>75%
- 书签A16DA9EE Green light flashes 3 times 75%> power>50%
- 书签B9185C36 Green light flashes twice 50%> power>25%
- 书签4A4B4482 Green light flashes once 25%> power >1%
- 书签C2AD09EB In power on state
- 书签8B27B844 power<20%, the red light is always on
- 书签76995E8E Device charging
- 书签E9606547 *The device is equipped with a double-headed USB charging cable, can charge both transmitter and receiver at the same time. Please use 5V 1A adapter for charging.
- 书签6AFB1700 *The device uses a polymer lithium battery, which needs to be charged before use. if it is not used for a long time, charge the product once every three months to activate it.
- 书签47D0302A *After plugging in the charging cable, if the indicator yellow lights are always on, indicating that the charging is faulty, and should be repaired by professional maintenance personnel.
- 书签E4827D40 5V 1A
- 书签1C030EE0 - When the device is in the charging state, the indicators on the transmitter and receiver are always red. When the power is fully charged, the indicators are always green. When the battery is fully charged and connected to charging again, the battery protection will be activated. The indicators on the transmitter and receiver will always be red, and after 20 minutes, the green lights will be on again.
- 书签3D98BBC5 > 3 months
- 书签943E6E7B Charging failure: Yellow light is always on
- 书签82BD1EA8 Power on / off
- 书签95B62490 - Power on: Long press the button for 2 seconds when the transmitter and receiver are in power off state. The LED indicator light is always green, the device power on successfully. Enter normal working condition. - Power off: Long press the button for 2 seconds while the transmitter and receiver are in power on state. The LED indicator light is off and the device shut down successfully. * After power on, the green light of the transmitter is always on, while the green light of the receiver is flashing, indicating that the device is not connected normally.
- 书签E17E9733 Long press for two seconds to turn on / off
- 书签24956C5B Mute function
- 书签4E7F9B09 - Under normal working condition of the devices, short press the button once on the transmitter, the green light flashing, indicating in mute mode, short press the transmitter again, the devices recover operation.
- 书签A1473200 Device pairing
- 书签5EC2D14C * If the devices cannot work normally after power on, and the green light of the transmitter is always on while the green light of the receiver is flashing, the devices need to be re-paired. - Re-pairing: In power off state, long press button for 5 seconds, the green and red lights on the transmitter and receiver blink alternately, the devices are pairing. When the devices are successfully paired, the green light are always on and the devices enter the working state. * The transmitter and receiver should be as close as possible when the devices are paired. If pairing unsuccessful, the indicator light will flash red and green alternately for 2 minutes and then automatically shut down.
- 书签1E7A18FA Device frequency hopping
- 书签EAAC943D * When using the device, there are signal interference around the device that cause the device not work properly. Frequency hopping can be performed on the device. - Device frequency hopping: Double-click the button on the transmitter, the green light on the transmitter flash once, and the green light on the receiver also flash once, the frequency hopping is successful.
- 书签F796158D 警告:为了减少火灾或者触电的危险,请勿将本设备置于雨中或者潮湿的地方 注意:请勿私自拆卸本设备,内部没有用户可维修的部件,请交给合格的维修人员处理
- 书签0CC23EFB ①请使用附带的充电线进行充电,如果不确定可用的电源类型,请咨询您的经销商。 ②本设备内置锂电池,请勿投入火中或热源的附近。 ③本设备没有防水功能,请勿投入水中或其他液体中。 ④请勿尝试自行维修本设备,因为打开盖子后可能会使您触碰到危险电压点或其他风险,如果本设备需要进行维修, 请交给合格的维修人员进行维修。 ⑤如果您长时间不使用本产品的时候,应该拔掉充电线。 ⑥避免电源线被踩踏或者在插头处插座和连接设备的位置绷的太紧。
- 书签CB4E3BFA 制造商:深圳市瑞孚科技有限公司 制造商地址 :广东省深圳市龙华新区大浪街道华宁路52号恒昌荣星辉科技园 联系电话:+86 755 2331 1770 中国制造
- 书签0326A27E 请在使用本产品前请详细阅读说明
- 书签52416A22 !
- 书签6763CB48 warning:In order to reduce the risk of fire or electric shock, please do not put the equipment in the rain or wet place Note: please do not disassemble the equipment without permission. There is no part that can be repaired by the user. Please hand it over to qualified maintenance personnel
- 书签E1D1BEF7 ①Please use the attached charging line for charging. If you are unsure of the type of power available, please consult your dealer. ②The device has a built-in lithium battery. Please do not put it into the fire or near the heat source. ③This equipment is not waterproof, do not put into water or other liquids. ④Please do not attempt to repair the equipment, because open the lid after may make you touch the danger point voltage or other risks,if this equipment is the need for maintenance, please to qualified maintenance personnel for repair. ⑤If you are not using this product for a long time, you should unplug the charging cable. ⑥Avoid the power cord being trampled or the position of the socket and the connecting device being too tight at the plug.
- 书签8294A076 COMPANY:SWIFF TECHNOLOGY CO.,LTD. ADDRESS:5/F, Building B,Hengchangrong\(Xinghui\) Industrial Park, No.52 Huaning Road.Longhua, Shenzhen, Guangdong Tel:+86 755 2331 1770 MADE IN CHINA
- 书签1350F6B9 Please read the instructions carefully before using this product
- 书签2D33BF99 !
- 书签4536280B 品 牌 名 称:Swiff 型 号 名 称:M1说明书四折页 尺 寸:107*115mm
- 书签79210ABF 印 刷 材 质:157g铜版纸 工 艺 说 明:双面四色印刷 覆哑膜 折好 刀 模 说 明:红色实线条为切线 虚线条为压线
- 书签7C1B24F7 修 改 次 数:0 日 期:20200303 备 注:无
- 书签5FDCD65E 107.00 mm
- 书签7DE46B83 正面
- 书签B3EEB2CB 反面
- 书签E4784FB2 FCC Warnning: Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: \(1\) This device may not cause harmful interference, and \(2\) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.