NE 4569l ASSEMBly INSTrUCTIoNS 6'-6'' Diameter Set Dim. No. of Children: Up to 2 Min. Use Zone: 18'-6'' Dia. Set Dim. 6'-6'' Dia. Est. Building Time: 2 hrs. WARNING: ! Assembly by an adult. 18'-6'' Diameter Min. Use Zone To register your product visit: http://www.swing-n-slide.com Other benefits include information on product warranties, assembly plan updates, joining our mailing list for new products and promotions, receiving our newsletter, and providing feedback on products.
Safety Checklist for Swing-N-Slide Play Sets and Accessories Observing the following statements and warnings reduces the likelihood of serious or fatal injury Installation Safety – Have You: Consulted the assembly instructions supplied with your particular model? Noted this accessory is to be used only on Swing•N•Slide approved designs? (Do not alter its design or add/remove components.) Made sure all hardware is tightened securely? (Supplied bolt covers must also be fastened securely.
This product is intended for single family home/residential use only and not intended for use in any public setting. Placement in any public setting constitutes a misuse of this product. IMPORTANT! ADDITIONAL REQUIRED SAFETY INSTALLATION INSTRUCTIONS According to ASTM requirements, all kits must be anchored to the ground and, if the unit has a climbing rope, the rope end must be anchored to the ground. If soil conditions permit stakes to be pulled out easily, cementing into ground is necessary.
Assembly Instructions TOOLS AND HARDWARE 4
Assembly Instructions Fig. 1 D C a x1 x3 x6 D a C C Fig. 2 K G I a a f g e i e i x4 x2 x3 x3 x8 x8 x8 x3 I I K G f I g I Fig.
Assembly Instructions Fig. 4 E c i E x2 x4 x4 c i Fig. 5 c i A B x2 x2 c B i A Fig. 6 F Fig. 7 x2 b i n i F n x1 x1 x2 n b F Note: Snug Bolt Only, Do NoT Overtighten.
Assembly Instructions Fig. 8 H x3 H 14'' H '' 12 12'' Optional Seesaw Anchoring Method: 1. Place the Seesaw in the desired position. Mark a 12'' x 12'' square around each of the Seesaw feet and, using these guidelines, dig holes 14'' deep. 2. Fill each hole with a minimum of 12'' of concrete. Do not exceed the ground level. 3. Place Seesaw back in desired position so that ends of legs are centered over cement fill. 4.
Questions???... Call our Customer Service Department at 1-800-888-1232 © PlayCore Inc.
NE 4569L INSTRUCCIONES DE ENSAMBLAJE INSTRUCTIONS D’ASSEMBLAGE 6'-6'' ø Dimensiones del juego 1,98 m ø Dim. de l’ensemble N.º de niños: Hasta 2 Zona de uso mínima: 18'-6'' Dimensiones del juego: 6'-6'' Tiempo estimado de armado: 2 horas. Nombre d’enfants : jusqu’à concurrence de 2 Zone d’utilisation minimale : 5,64 m Dim. de l’ensemble 1,98 m Durée du montage estimée : 2 heures. ! ADVERTENCIA: El ensamblaje lo debe hacer un adulto.
Lista de control de seguridad para los juegos y accesorios Swing-N-Slide Liste de vérification de sécurité pour les ensembles de jeu et les accessoires Swing-N-Slide Atender los siguientes enunciados y advertencias reduce la posibilidad de lesiones graves o fatales.
Este producto ha sido ideado para su uso en una residencia u hogar de una sola familia y no para usarse en lugares públicos. Su uso en lugares públicos constituye una mala utilización de este producto.
Ce produit est destiné à un usage résidentiel et familial seulement et n'est pas conçu pour une utilisation dans un endroit public. L'installation de ce centre de jeu dans un endroit public constitue une mauvaise utilisation de ce produit.
Assembly Instructions Assembly Instructions TOOLS AND HARDWARE 5
Assembly Instructions Assembly Instructions Fig. 1 D C a x1 x3 x6 D a C C Fig. 2 K G I a a f g e i e i x4 x2 x3 x3 x8 x8 x8 x3 I I K G f I g I Fig.
Assembly Instructions Fig. 4 E c i E x2 x4 x4 c i Fig. 5 c i A B x2 x2 c B i A Fig. 6 F Fig. 7 x2 b i n i F n x1 x1 x2 n b F Nota: Sólo apriete el perno, NO apriete en exceso. Remarque : Évitez de serrer excessivement les boulons.
x2 x4 x4 x2 x4 x4 H x3 H x3 Assembly Instructions Fig. 8 H x2 x4 x4 H x3 H 14'' 36 cm H x2 x2 '' 12 m c 30 H x2 x2 12'' 30 cm Método opcional de anclaje del sube y baja: 1. Coloque el sube y baja en la posición deseada. Marque un cuadrado de 12'' x 12'' alrededor de cada una de las patas del sube y baja y con esta guía cave orificios de 14'' de profundidad. 2. Llene cada orificio con un vaciado mínimo de concreto de 12''. No vacíe por encima del nivel del piso. 3.
