PB 8137 WARNING: ! Assembly by an adult. IMPORTANT!! ! ADVERTENCIA: El ensamblaje lo debe hacer un adulto. PLEASE READ BEFORE BEGINNING ASSEMBLY!! Please make sure all lumber, hardware and accessory parts are accounted for. If you are missing anything, please DO NOT RETURN to the store where purchased. Please call our ! AVERTISSEMENT: Customer Service Department at the number below. L’assemblage doit être ASSEMBLY INSTRUCTIONS exécuté par un adulte.
Safety Checklist for Swing-N-Slide Play Sets and Accessories Observing the following statements and warnings reduces the likelihood of serious or fatal injury Installation Safety – Have You: Consulted the assembly instructions supplied with your particular model? Noted this accessory is to be used only on Swing•N•Slide approved designs? (Do not alter its design or add/remove components, this accessory is intended for wooden playsets only, do not install on metal frame playsets).
This product is intended for single family home/residential use only and not intended for use in any public setting. Placement in any public setting constitutes a misuse of this product. IMPORTANT! ADDITIONAL REQUIRED SAFETY INSTALLATION INSTRUCTIONS According to ASTM requirements, all kits must be anchored to the ground and, if the unit has a climbing rope, the rope end must be anchored to the ground. If soil conditions permit stakes to be pulled out easily, cementing into ground is necessary.
DIMENSIONS 10 1-3/8 25 4-1/2 10 22 1-3/8 MINIMUM USE ZONE FOR PLAY EQUIPMENT SHALL EXTEND NO LESS THAN 72” FROM ALL SIDES OF THE PLAY STRUCTURE. SWING USE ZONE EXTENDS NO LESS THAN 168”. SWINGS MUST HAVE A MINIMUM CLEARANCE OF 8” ABOVE THE PROTECTIVE SURFACING.
TOOLS REQUIRED DRILL 1/2” SOCKET & WRENCH HAMMER ADJUSTABLE WRENCH TAPE MEASURE SCREWDRIVER PHILLIPS BIT CARPENTER SQUARE SAFETY GLASSES 1/8” DRILL BIT INCLUDED HARDWARE 8mm Loc Washer (x8) 30mm Deck Screw (x42) 5/16” x 1-1/2” Lag Screw (x4) 8mm Washer (x8) 1-1/2” Deck Screw (x40) 2” Deck Screw (x30) 5/16-18 T-Nut (x10) Large 2-1/2” Deck Screw (x136) Weld-Nut (x8) #8 x 1/2” Pan Screw (x2) #12 x 3/4” Pan Screw (x6) 5/16’’ Loc Washer (x8) 5/16” Washer (x32) 5/16” Loc Nut (x12) 5/16-18 T-Nut
/2’’ /4’’ INCLUDED HARDWARE 5/16”-18 x 7-1/2” Hex Bolt (x1) 5/16”-18 x 6” Hex Bolt (x1) 5/16”-18 x 5” Hex Bolt (x1) 5/16”-18 x 4-1/2” Hex Bolt (x3) 5/16”-18 x 4” Hex Bolt (x2) 5/16”-18 x 3-1/4” Hex Bolt (x6) /2’’ 5/16”-18 x 3” Hex Bolt (x2) /4’’ 5/16”-18 x 2-3/4” Hex Bolt (x4) 1/4”-20 x 1-1/4” Hex Head Bolt (x8) 6
INCLUDED COMPONENTS ID Tag (x1) Beam Clamp Slotted (x4) Beam Brace (x1) Swing Beam Bracket (x2) Play Handle (x1) 5/16’’ x 5-1/4’’ Swing Hanger (x4) Anchor It Strap (x4) Anchor It (x4) STD Swing Seat (x2) Quick Link (x4) Plan (x1) 58” Dipped Chain (x4) 3/8” DRILL BIT (x1) Cool Wave Slide (x1) Long Tarp (x1) Climbing Rock (x4) 7
BOARD LIST (4) [PF 4878] 5/4’’ x 4’’ x 10-1/2’’ (1) [PF 4873] 3’’ x 5-1/2’’ x 63-7/8’’ SWING BEAM (2) [PF 4865] 5/4’’ x 4’’ x 45’’ (1) [PF 4872] 3’’ x 3’’ x 50’’ SWING BEAM SUPPORT (4) [PF 4864] 5/4’’ x 4’’ x 26-3/4’’ (1) [PF 4877] 3’’ x 3’’ x 24’’ TOWER BEAM SUPPORT (1) [PF 4863] 5/4’’ x 4’’ x 24’’ (2) [PF 4862] 5/4’’ x 4’’ x 23’’ (2) [PF 4861] 1’’ x 6’’ x 33’’ (3) [PF 4859] 1’’ x 6’’ x 26-3/4’’ (1) [PF 4880] 1’’ x 4’’ x 42-1/4’’ (2) [PF 4879] 1’’ x 6’’ x 26-3/4’’ PICNIC TABLE/SEAT (1) [PF 4855]
USE THE CORRECT FASTENER Use the guides below to help select the correct length, quantity & location of screws for the board installation. Avoid splitting your lumber by offsetting your screws at least 3/4” from edge. All hardware should be driven until flush with the surface or no deeper than 1/16”.
STEP 1 PRE-DRILL BOARDS TO MINIMIZE SPLITTING PF 4854 1’’x4’’x24’’ (3) 1-1/2’’ Screws Per Joint 5/16’’ Washer 5/16’’Loc-Washer 5/16-18 X 4-1/2’’ Hex Head Bolt T-Nut Small Flush PF 4870 2’’x4’’x85-1/2’’ PF 4870 2’’x4’’x85-1/2’’ PF 4868 2’’x4’’x70’’ 23” (3) 2-1/2’’ Screws Per Joint PF 4866 2’’x4’’x24’’ FLIP FRAME A OVER PF 4867 2’’x4’’x49-5/8’’ PF 4867 2’’x4’’x49-5/8’’ (3) 2-1/2’’ Screws Per Joint Flush FRAME A T-Nut Large 5/16’’ Washer 5/16’’Loc-Washer (2) 2-1/2’’ Screws 5/16-18 X 2-3/4’’ H
STEP 2 Flush PF 4854 1’’x4’’x24’’ (3) 1-1/2’’ Screws Per Joint PRE-DRILL BOARDS TO MINIMIZE SPLITTING PF 4869 2’’x4’’x85-1/2’’ PF 4866 2’’x4’’x24’’ T-Nut Large 5/16’’ Washer PF 4869 2’’x4’’x85-1/2’’ 5/16’’ Loc-Washer 5/16-18 X 2-3/4’’ Hex Head Bolt (2) 2-1/2’’ Screws PF 4863 5/4’’x4’’x24’’ (3) 2-1/2’’ Screws Per Joint Flush FRAME B 2-1/2” Deck Screw (x10) 1-1/2” Deck Screw (x6) 1. Assemble Frame B as shown.
STEP 3 Flush Flush PF 4864 5/4’’x4’’x26-3/4’’ (3) 2-1/2’’ Screws Per Board PF 4864 5/4’’x4’’x26-3/4’’ (2) 2-1/2’’ Screws Per Board Frame A Check to make sure structure is square 2-1/2” Deck Screw (x10) 1. Assemble Frame A as shown.
STEP 4 (3) 2-1/2’’ Screws Per Board (2) 2-1/2’’ Screws Per Board Frame B Frame A Check to make sure structure is square 2-1/2” Deck Screw (x10) 1. Attach Frame A to Frame B as shown. Note Frame B orientation.
STEP 5 (2) PF 4854 1’’x4’’x24’’ (4) 2-1/2’’ Screws Per Board Space Deck Boards Evenly (3) PF 4859 1’’x6’’x26-3/4’’ (4) 2-1/2’’ Screws Per Board PF 4853 1’’x4’’x17-1/2’’ (4) 30mm Screws 2-1/2” Deck Screw (x20) 30mm Deck Screw (x4) 1. Attach deck boards as shown. 2. Attach slide support board as shown.
STEP 6 PRE-DRILL BOARDS TO MINIMIZE SPLITTING PF 4880 1’’x4’’x42-1/4’’ (2) 1-1/2” Deck Screws per joint 9’’ 26-1/2’’ Check to make sure structure is square 1-1/2” Deck Screw (x8) 1. Attach swing safety board.
STEP 7 5/16’’ Washer T-Nut Large (2) 2-1/2’’ Screws 5/16’’ Loc-Washer PF 4877 3’’x3’’x24’’ TOWER BEAM SUPPORT 5/16-18 X 4’’ Hex Head Bolt Counter Bore Holes Down 2-1/2” Deck Screw (x4) 1. Attach Swing Beam Support Frame A as shown. Note the post orientation.
STEP 8 (2) PF 4860 1’’x6’’x26-3/4’’ (6) 2-1/2” Deck Screws per board PRE-DRILL BOARDS TO MINIMIZE SPLITTING PF 4854 1’’x4’’x24’’ (6) 1-1/2” Deck Screws 7’’ 25’’ PF 4855 1’’x4’’x26-3/4’’ (4) 2-1/2” Deck Screws PF 4858 1’’x6’’x24’’ (6) 1-1/2” Deck Screws Check to make sure structure is square 2-1/2” Deck Screw (x16) 1-1/2” Deck Screw (x12) 1. Attach board(s) to Frame B as shown. Note the post orientation.
STEP 9 COUNTERBORE HOLES ON TOP PF 4873 3’’x5-1/2’’x63-7/8’’ Swing Beam 5/16’’ T-Nut Large 5-1/4’’ Swing Hanger Beam Clamp 3 2 1 x4 Correct Orientation 4 (4) 30mm Deck Screws 5 1. Attach Swing Hanger(s) to swing beam as shown.
STEP 10 PF 4872 3x3x50 A-Frame SB Support 5/16”-18 x 6” Hex Head Bolt 5/16” Washer 5/16” Washer 5/16” Loc Nut (2) PF 4874 2’’x4’’x69-1/8’’ A-Frame 5/16”-18 x 3-1/4” Hex Head Bolt 5/16” Washer 5/16” Washer 5/16” Washer 5/16”-18 x 4-1/2” Hex Head Bolt 5/16” Loc Nut (2) 2-1/2’’ Screws 5/16” Loc Nut 5/16”-18 x 3-1/4” Hex Head Bolt (2) 2-1/2’’ Screws 5/16” Washer PF 4871 2’’x4’’x43-1/2’’ A-Frame Support (2) 2-1/2’’ Screws 5/16” Loc Nut 5/16” Washer 2-1/2” Deck Screw (x6) 1. Assemble A-Frame as shown.
STEP 11 (2) Swing Beam Bracket 5/16”-18 x 3-1/4” Hex Head Bolt 5/16” Washer 5/16” Loc Nut 5/16”-18 x 3-1/4” Hex Head Bolt 5/16” Washer 5/16” Washer 5/16” Washer 5/16” Loc Nut 1. Attach Swing Beam Bracket to A-Frame & Swing Beam as shown.
STEP 12 Beam Brace 5/16”-18 x 3” Hex Head Bolt 5/16” Washer 5/16” Loc Nut 5/16” Washer 5/16”-18 x 7-1/2” Hex Head Bolt 5/16”-18 x 5” Hex Head Bolt 5/16” Washer 5/16” Washer 5/16” Loc Nut x2 1. Attach Swing Beam to tower as shown.
STEP 13 (3) PF 4857 1’’x6’’x21’’ (4) 30 mm Deck Screws per board (2) PF 4861 1’’x6’’x33’’ (4) 30 mm Deck Screws per board Flush PRE-DRILL BOARDS TO MINIMIZE SPLITTING (2) 2-1/2” Deck Screws per board 2-1/8” gap typical 2” gap typical Flush Flush INSIDE VIEW INSIDE VIEW 30mm Deck Screw (x20) 2-1/2” Deck Screw (x4) 1. Attach barrier boards as shown.
STEP 14 (1) PF 4879 1’’x6’’x26-3/4’’ 3/4’’ 1-3/8’’ (2) PF 4878 5/4’’x4’’x10-1/2’’ (4) 1-1/2’’ Deck Screws x2 PRE-DRILL BOARDS TO MINIMIZE SPLITTING 13’’ (3) 2’’ Deck Screws per side 23-1/8’’ (3) 2’’ Deck Screws per side 2” Deck Screw (x12) 1-1/2” Deck Screw (x8) 1. Assemble and attach Picnic Table and Bench as shown.
17’’ STEP 15 1-1/2’’ FLUSH (7) PF 4875 1’’x6’’x20’’ ROCK WALL 1-1/2’’ Gap All Boards PRE-DRILL BOARDS TO MINIMIZE SPLITTING (2) PF 4876 2’’x4’’x50’’ ROCK WALL SUPPORT (2) 2-1/2’’ Screws per joint (2) 2-1/2’’ Screws per joint (2) Weld Nuts Underdeck View (2) 1-1/4’’ Hex Head Bolts (2) 8mm Loc-Washer Per Rock (2) 8mm Flat Washer Per Rock 2-1/2” Deck Screw (x32) 1. Assemble Rock Wall as shown. 2.
STEP 16 (8) 2’’ Deck Screws 1 2 (2) PF 4862 5/4’’x4’’x23’’ (3) 2’’ Deck Screws Per Joint 8” -7/ 27 Flush (2) PF 4865 5/4x4x45 (2) PF 4856 1x4x26 Flush 3 PRE-DRILL BOARDS TO MINIMIZE SPLITTING 3/16” Washer #12 x 3/4” Pan Screw 4 #12 x 3/4” Pan Screw (x6) 2” Deck Screw (x18) 2-1/2” Deck Screw (x8) (2) 2-1/2” Deck Screws per joint 1. Assemble and install Roof as shown.
STEP 17 1” Truss Screws (2) 30mm Deck Screws Grade 2” PF 4945 2’’x4’’x17-1/4’’ Slide Stake 30mm Deck Screw (x2) 1. Attach slide as shown.
STEP 18 5/16” Washer Fold up Anchor-It Strap 1-1/2” Lag Screw Anchor-It 5/16’’ x 1-1/2” Lag Screw (x4) 1. Place swing set in final location and mount Anchor-It(s) at locations circled above. 2. Twist the Anchor-It into the ground until only the loop is exposed. 3. Place Anchor-It Strap thru loop, fold the ends together and attach to the unit as shown. Note: Keep as little play as possible using any of the holes in the strap that work best.
STEP 19 1/4” Washer 1/4’’ x 1-3/4” Pan Screw 11” 1/2” Pan Screw (x2) 1-3/4” Pan Screw (x2) 1.
Swing Seat Assembly BOTTOM OF SEAT BOTTOM OF SEAT STEP 20 1. Take one length of chain and place the outermost link of chain through the Quick Link as shown. 2. Place the Quick Link through the Grommet of the swing seat as shown. 3. Tighten the threaded sleeve of the Quick Link with a suitably sized wrench so that the seat is securely attached and the Quick Link cannot be easily loosened. Repeat for second chain, Quick Link and Swing Seat Grommet.
800•888•1232 Got Questions? We’ve got answers! Call our Customer Support Representatives Available Monday - Friday, 7am - 5pm (CST) Weekend support available April through Labor Day Also available on Memorial Day, Fourth of July & Labor Day Technical Support from experienced Swing-N-Slide Customer Service Representatives who have actually built a swing set themselves. © Swing-N-Slide Inc.
