Model: PB 8330 S IN CTION ANISH U R T S IN SP N H AND FRENC BE FOUND OOM CAN N-SLIDE.C SWING IMPORTANT!! PLEASE READ BEFORE BEGINNING ASSEMBLY!! Please make sure all lumber, hardware and accessory parts are accounted for. If you are missing anything, please DO NOT RETURN to the store where purchased. Please call our Customer Service Department at the number below. ASSEMBLY INSTRUCTIONS Swing-N-Slide • 1212 Barberrt Drive • Janesville, Wisconsin 53545 Visit our web sit at: www.swing-n-slide.
5CHGV[ %JGEMNKUV HQT 5YKPIÄ0Ä5NKFG 2NC[ 5GVU CPF #EEGUUQTKGU 1DUGTXKPI VJG HQNNQYKPI UVCVGUOGPVU CPF YCTPKPIU TGFWEGU VJG NKMGNKJQQF QH UGTKQWU QT HCVCN KPLWT[ three 6JKU RNC[UGV JCU DGGP FGUKIPGF HQT WUG D[ C OCZKOWO QH GKIJV QEEWRCPVU CV QPG VKOG JCXKPI C EQODKPGF YGKIJV QH RQWPFU 345 pounds.
PLAYSET MAINTENANCE Cosmetic defects that do not affect the structural integrity of the product, or natural defects of wood such as warping, splitting, checking, twisting, shrinkage, swelling or any other physical properties of wood that do not present a safety hazard, are not covered by our warranty. To help minimize these natural defects we recommend applying a sealer or stain every two or three years, or more often as the climate dictates.
PLAYGROUND SURFACING MATERIALS SECTION 4 OF THE CONSUMER PRODUCT SAFETY COMMISSION'S OUTDOOR HOME PLAYGROUND SAFETY HANDBOOK9 Select Protective Surfacing One of the most important things you can do to reduce the likelihood of serious head injuries is to install shock-absorbing protective surfacing under and around your play equipment. The protective surfacing should be applied to a depth that is suitable for the equipment height in accordance with ASTM Specification F 1292.
SAFETY ZONE 13'-4" 6' R 7'-0" Height 8'-0" 26'-8" 9'-5" 13'-4" 21'-5" MINIMUM USE ZONE FOR PLAY EQUIPMENT SHALL EXTEND NO LESS THAN 72" FROM ALL SIDES OF THE PLAY STRUCTURE. SWING USE ZONE EXTENDS NO LESS THAN 160". SWINGS MUST HAVE A MINIMUM CLEARANCE OF 8" ABOVE THE PROTECTIVE SURFACING.
TOOLS REQUIRED DRILL SCREWDRIVER 1/2” & 7/16’’ SOCKETS & WRENCH LADDER HAMMER CARPENTER SQUARE ADJUSTABLE WRENCH SAFETY GLASSES 1/8" DRILL BIT & 1/4" DRILL BIT TAPE MEASURE PLIERS INCLUDED HARDWARE 3/8 x 5" carriage bolts (x4) 3/8" Flat Washer (x18) 3/8 x 4" carriage bolts (x8) 3/8 x 2-1/2" Lag Screws (x6) 5/16" Flat Washer (x4) 3/8" Lock Washer (x6) Quick Clips (x6) 1/4" Flat Washer (x8) 3/8" Loc Nut (x12) 1/4" Lock Washer (x8) 1/4 x 2-1/2" Panhead Screws (x8) 5/16 x 1-1/2" Lag Scre
COMPONENTS 4" Dia. x 93" Plastic-coated Post (x1) 3-1/4" Dia. x 93" Plastic-coated Post (x4) 1-1/2" Dia.
90° 1/8" pilot holes 45" ! 3-1/4 Dia. x 93" Plastic-Coated Posts (x2) Temporary carriage bolts ° 90 1/4 x 2-1/2" Panhead Screw 1/4" lock washer 1/4" flat washer A-Brace Weep Holes Note: Fasteners should be snug at this point. You will assemble two A-frame post assemblies. 1. Place two posts side-by-side on a flat surface. 2. Temporarily insert two 5” carriage bolts to keep posts square for pre-drilling. ! It's important to drill holes square to holes in posts. 3. Measure and mark holes.
! Center bracket on posts ! Plastic sleeve may extend past cap edge, but locate bracket flush to cap edge. Flush with edges of caps ! ! Fig. 1 ! Edges still touch Fig. 2 Carefully mark center of all four holes 1/8" predrill 1/4" predrill Fig. 3 3/8 x 2-1/2" Lag Screw Tighten Securely 1/4 x 2-1/2" Panhead Screw 1/4" lock washer 1/4" flat washer 3/8" lock washer 3/8" flat washer A-brace Fig. 4 (2) Holes this end Support 1.
3/8" lock nut 3/8" flat washer 1. Carefully flip the A-frame over. 2. Remove any wood or plastic material in hole openings. Attach two brackets to the post as shown. Tighten fasteners slightly snug at this point. Do NOT fully tighten. 3. Assemble a second A-frame assembly.
1 T-nut 2 3 4 Correct orientation Slo t Beam Clamp 1 Swing Hanger 1-1/4" Screws 1. Remove any wood or plastic material in hole openings. Tap T-nuts into holes as shown. 2. Insert Hangers through Beam Clamp and into T-nuts. 3. Use screwdriver as lever to help seat hanger securely into slotted beam clamp. Secure slotted clamp with screws.
3/8" lock nut 3/8" flat washer 3/8 x 5" Carriage bolt This hole empty. 1. Remove any wood or plastic material in hole openings. Locate the swing beam between the brackets and attach as shown. HINT: Loosen bolts in 3-1/4" posts to help align holes for 5" bolts if necessary. Tighten fasteners slightly snug at this point. Do NOT fully tighten.
3/8" lock nut 3/8" flat washer 3/8 x 5" Carriage bolt 1. Carefully swing the A-frame assembly up and insert a second bolt. Attach as shown. Tighten fasteners slightly snug at this point. Do NOT fully tighten.
3/8" lock nut 3/8" flat washer This hole empty 3/8 x 5" Carriage bolt 1. Locate the second A-frame assembly and remove any wood or plastic material in hole openings. Attach to swing beam as shown. HINT: Loosen bolts in 3-1/4" posts to help align holes for 5" bolts if necessary. Tighten fasteners slightly snug at this point. Do NOT fully tighten.
3/8" lock nut 3/8" flat washer 3/8 x 5" Carriage bolt Tighten ALL Lock nuts until 2 threads minimum extend past nut. 3/8" flat washer 3/8" lock washer 3/8 x 2-1/2" Lag screw Swing A-Frame up 1/4" Pre-drill 1. Carefully swing the A-frame up and insert a second bolt. Attach as shown. Tighten fasteners slightly snug at this point. Do NOT fully tighten. 2. Carefully move A-frame posts to make sure playset is square. 3. Now fully tighten all fasteners.
BOTTOM OF SEAT BOTTOM OF SEAT Plastic-coated end. Swing Seat Assembly 1. Take one length of chain and place the outermost link of chain through the Security Link as shown. 2. Place the Security Link through the Grommet of the swing seat as shown. 3. Tighten the threaded sleeve of the Security Link with a suitably sized wrench so that the seat is securely attached and the Security Link cannot be easily loosened. Repeat for second chain, Security Link and Swing Seat Grommet.
1 2 3 4 Plastic-coated end. Ring-Trap Combo Assembly 1. Attach Security Link to chain oriented as shown. 2. Attach Security Link to gym ring as shown. Attach second set of Security Links (3) links up. Attach Trapeze Bar as shown. 3. Tighten all Security Links closed with wrench.
Affix Label as shown using (4)1/2" Screws Fold up 5/16” Washer 1-1/2” Lag Screw Anchor-It Strap Anchor-It 1 At locations circled above, twist the Anchor-It into the ground until only the loop is exposed. 2. Place Anchor-It Strap thru loop, fold the ends together and attach to the unit as shown. Note: Keep as little play as possible using any of the holes in the strap that work best.
SURYLGHV FRQ¿GHQFH DQG GHPRQVWUDWHV RXU FRPPLWPHQW WR
Got Questions? We’ve got answers! Call our Customer Support Representatives 1-800-888-1232 Available Monday - Friday, 7am - 5pm (CST) Weekend support available April through July Technical support from experienced customer service representatives who have actually built a swing set themselves. @ Swing-N-Slide Inc.
