It’s time to swing! DIY SWING SET Manual
INTRODUCTION Dear valued customer Congratulations! You have purchased the Swingan DIY Swing set, where the fun begins! Please read this entire booklet completely before beginning the assembly process. We have included important safety information that you must adhere to, to prevent injuries. PLEASE RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE. KEEP THEM IN A SAFE PLACE WHERE YOU CAN REFER TO THEM AS NEEDED. • Instructions for use – Safety Instructions .............. PAGE 3 • Safe Use ..................
INSTRUCTIONS FOR USE – SAFETY INSTRUCTIONS Carefully read the following instructions BEFORE using your Swingan product. This information was meticulously put together for your safety and to reduce risk of injury. Always keep the safety of your children in mind as you build your set and as your children play on it. SAFETY ADVISORIES INSTALLATION • Use a water sealant on your beams to protect the wood and prevent cracking and warping. • Install the swing set only on a level surface.
SAFE USE ● The swing set is designed to be used by children ages 4 and up. No more than 4 persons should use the set at once, not more than one person per swing. ● An adult should always supervise children using the swing set. ● Do not allow a child or adult to use the swing set if they have a physical condition that hampers their ability to use the equipment properly. ● Teach children not to walk close to, in front, in between or behind moving swings.
MAINTENANCE ● Carry out maintenance checks monthly or before the start of a usage period, checking more regularly in seasons of high usage. ● Inspect nuts and bolts for tightness ● Oil all moving steel parts ● Check water sealant and repaint areas of exposure. We recommend sealing annually to keep your swing set looking brand new.
SWINGAN WARRANTY S W I N G A N Swingan products are manufactured under the highest standards of quality and workmanship. Your Swingan item comes with a limited warranty showing our dedication to providing only quality products. Our warranty covers defects in material and workmanship. Allowing for reasonable wear and tear, should any such defect become apparent during the warranty period, Swingan will supply a free replacement for any defective part (installation not included).
KIT COMPONENTS Part Description Quantity A-Frame Backet 2 Bracket Hardware 2 Belt Swing Seat 1 Coated Chains 2 Fully Assembled Trapeze Bar with Rings 1 Fully Assembled Disc Swing 1 Fully Assembled Standing Swing 1 Screw Swing Hanger 7 Snaphook 7 PAGE 7
TOOLS REQUIRED 6. 1. ELECTRIC DRILL 2. TAPE MEASURE 7. SOCKET & WRENCH 3. CIRCULAR SAW 8. HAMMER PLIERS 9. 4. PHILIPS BIT & SPADE BIT WRENCH 5. 10.
Before starting assembly, check that you have all necessary parts. If any parts are missing or damaged on delivery, please contact Swingan customer support directly on 1-800-574-9323 for immediate replacement. HOW TO BUILD YOUR SWING SET In order to build this swing set you must purchase wooden beams. The A-frame brackets are designed to be used with a 4x6 top beam and 4x4 support beams. To build the swing set 8ft depth and 7.8ft height.
PREPARING THE SWING HANGING BAR • Measure and mark the 120” top beam for placement of the swings. Make the markings on the 4” surface of the beam. Mark each spot where a swing hanger screw must be installed to hang a swing chain on. See the diagram below for the measurements of how to place your swings in accordance with safety requirements. Dotted lines indicate where markings must be made. 12’’ 16’’ 8’’ 15’’ 8’’ 16’’ 25’’ 20’’ • Drill holes through the beam using a 3/8" drill bit.
ATTACHING THE TOP BEAM TO THE A-FRAMES NOTE: YOU WILL REQUIRE THE ASSISTANCE OF ANOTHER PERSON FOR THIS PART OF THE ASSEMBLY. 1. Lay the top beam on the ground on a 6” side, with the screw hangers on the side closer to you. 2. Stand one A-Frame on its side, with one beam flat on the ground and the other in the air. The legs should be pointing in the same direction as the swing hangers. (See Image) 3. Lift the top beam slightly and tilt it so that it can slide into the opening on the A-Frame bracket.
ASSEMBLING THE BELT SWING 1. Collect the belt swing seat and the two coated chains. 2. Thread the S-Hook on the end of a chain through the hole on one end of the swing seat. 3. Crimp the hook opening closed using pliers to secure the connection. (See Image) 4.Repeat steps 2-3 with the S-Hook on the other chain, connecting it to the hole on the other end of the swing seat. CRIMP THE HOOK OPENING CLOSED HANGING THE SWINGS All the swings are now fully assembled.
Your swingset is fully assembled and ready for FUN! CONTACT INFO: US: 1800-574-9323 UK: 020-3150-0484 Support@swingan.com 2 Mill St. Cornwall NY 12518 Web: www.swingan.