CHANGING YOUR LANDSCAPE SINCE 1945 swisherinc.com OWNER’S MANUAL 19975 Starting Serial #: L215-001001 Commercial Pro Plow Combo, 50" ATV IMPORTANT Read and follow all Safety Precautions and Instructions Before Operating this Equipment.
LIMITED WARRANTY The manufacturer’s warranty to the original consumer purchaser is: This product is free from defects in materials and workmanship for a period of one (1) year from the date of purchase by the original consumer purchaser. We will repair or replace, at our discretion, parts found to be defective due to materials or workmanship. This warranty is subject to the following limitations and exclusions: 1.
SAFETY PRECAUTIONS This Safety Alert Symbol indicates important messages in this manual. When you see this symbol, carefully read the message that follows and be alert to the possibility of personal injury. • Read the manual. Learn to operate this machine safely. • Keep the operating speed LOW!!!!! Do not operate over 5 MPH (8 KPH). • Allow only responsible adults who are familiar with these instructions to operate this machine. Never allow children to operate this machine.
UNIVERSAL MOUNT PARTS DETAIL MOUNTING OPTIONS There are four different mounting bracket options provided for mounting to various front axle styles. Long Brackets 2632 and 2634 (13, 15) and Short Brackets 2633 and 2635 (7, 12) are two sets that will work on most ATVs. The determining factor is what type of A-arms (lower portion of the front axle) are used on your ATV. The Long Brackets are shown as an example at the bottom of this page (See Fig. 1).
TO ENSURE PROPER ASSEMBLY, CAREFULLY FOLLOW ALL INSTRUCTIONS LISTED BELOW Universal Mount Assembly 1. 2. 3. 4. 5. 6. 7. 8. Lay out the hardware under the ATV, as shown on the previous page. If needed, for clearance, raise the front of the ATV. Make sure the support used is very stable; do not rely on hydraulic jacks. Loosely attach the Mounting Brackets best suited for your vehicle to the lower A-arms as near as possible to the inside of the wheel. See the example at the bottom of page 4.
Cut Edge 20084 (9) is preinstalled to Blade 2150 (29) using 5/16-18 X 1 Carriage Bolt 10197 (8) and 5/16-18 Serrated Flange Nut NB170 (11).
TO ENSURE PROPER ASSEMBLY, CAREFULLY FOLLOW ALL INSTRUCTIONS LISTED BELOW Pivot Latch Assembly These steps need to be done in sequence: 1. Lay parts down in the order they are shown below. 2. Slide Plow Mount 2588 (24) into Pivot Weldment 2323 (18) and secure with ½-13 X 3½ Bolt NB577 (25) and ½-13 Nyloc Nut NB281 (15). Do not overtighten; the Plow Mount must be able to pivot freely. 3. Assemble the Pivot Latch assembly in the order shown below.
TO ENSURE PROPER ASSEMBLY, CAREFULLY FOLLOW ALL INSTRUCTIONS LISTED BELOW Pivot Mount Assembly 1. 2. 3. Connect Skid Weldment 10068 (12) through the channel on the outer right edge of the Blade using Clevis Pin NB300 (7) and Hair Pin NB127 (10) in the order shown below. Repeat for the left side. The height can be adjusted using the holes in the Skid Weldment leg.
TO ENSURE PROPER ASSEMBLY, CAREFULLY FOLLOW ALL INSTRUCTIONS LISTED BELOW Tilt Spring Assembly 1. 2. 3. Assemble one 3/8-16 Nut NB212 (4) to each Eyebolt NB635 (5). Attach one end of Tilt Spring 2335 (6) to the Plow Mount assembly tab and the other end to Eyebolt NB635 (5). Assemble Eyebolt NB635 (5) into the hole at the top of the Blade. Secure with 3/8 Washer NB272 (3) and 3/8-16 Nut NB182 (2). Place Vinyl Caps AS125 (1) over the remaining threads of the Eyebolt. Repeat for the other side.
TO ENSURE PROPER ASSEMBLY, CAREFULLY FOLLOW ALL INSTRUCTIONS LISTED BELOW Connecting the Blade to the Universal Mount 1. 2. Connect the Blade Assembly to the Universal Mount Assembly by lining up the holes in Plow mount Weldment 2588 (24) with the holes in Slide Bar Weldment 20086 (16, pg 4). Insert Plow Mount Pin 2642 (26) through holes and secure with Pin NB506 (32). Unless otherwise stated, the numbers in parenthesis on this page refer to items from the table on page 6.
NOTES 11
CHANGING YOUR LANDSCAPE SINCE 1945 swisherinc.
