www.swisherinc.com OWNER’S MANUAL STARTING SERIAL #: L116-140001 MODEL NO. FC14560BS FC14560BS-CA FC14560BSXP FC17560BS FC17560BS-CA FC17560BSXP POL14560A POL14560A-CA POL14560AEX IMPORTANT Read and follow all Safety Precautions and Instructions before operating this equipment. 60” FAST FINISH TRAIL MOWER Assembly Operation Service and Adjustment Repair Parts ade I The SWISHER ACQUISITION INC. 1602 CORPORATE DRIVE., WARRENSBURG MO 64093 PHONE 800-222-8183 FAX 660-747-8650 EMAIL CustomerCare@SwisherInc.
LIMITED WARRANTY The manufacturer’s warranty to the original consumer purchaser is: This product is free from defects in materials and workmanship for a period of one (1) year from the date of purchase by the original consumer purchaser. As required by CFR § 1060.120, the fuel system related components, which have been certified to this equipment by SAI are to be free of defects in material and workmanship for a period of two (2) years from the date of purchase by the original consumer purchaser.
SAFETY PRECAUTIONS This Safety Alert Symbol indicates important messages in this manual. When you see this symbol, carefully read the message that follows and be alert to the possibility of personal injury. Read this manual completely. This machine can amputate hands, feet, and throw objects. Failure to observe the following safety instructions could result in serious injury or death. • • • • • • • • • • • • • • • • • • • Read the manual. Learn to operate this machine safely.
SAFETY DECALS Replace decals immediately if damaged. Order by part number from Swisher.
REQUIRED ASSEMBLY FRONT WHEEL CASTER ASSEMBLY 1. Remove single nut and washers from caster shaft. 2. Place one washer (NB195) on the shaft of the caster/wheel subassembly. 3. Slide same shaft through the bearing/frame with wheel towards the ground. 4. Place the other washer (NB195) on the shaft; it should be resting on the top bearing. 5. Add thin washer (17x195). 6. Thread nyloc jam nut onto shaft. 7. Tighten nut snuggly, making sure shaft threads enter the nyloc of the nut.
OPERATING YOUR TRAIL MOWER The operation of any mower can produce foreign objects to be thrown into the eyes, resulting in severe eye damage. Always wear certified safety glasses or wide-vision safety goggles over spectacles before starting any cutting machine and while operating such a machine. The operation of any cutter produces sound waves that are damaging to the human ear. Ear protection is recommended. CAUTION! Tragic accidents can occur if the operator is not alert to the presence of children.
• • • • • • • • Engine must be level to accurately check and fill oil. Do not overfill. Make sure the tow vehicle parking brake is set, mower is level, and blades are disengaged. Check spark plug wire, oil, and fuel. Check all electrical connections (See Schematics). Make sure toggle switch is turned “ON” and the red tether is properly attached. Set engine idle to “CHOKE” position. With feet clear of mower deck, turn key switch to the “START” position and release when engine begins to run.
ALTERNATIVE STOPPING METHOD • Bring vehicle to complete stop, shut off engine, and set parking brake. • Disengage blade engage lever (18976). • Manually shut toggle and key switches to their “OFF” positions. • Always remember to remove keys to avoid irresponsible usage. TRANSPORTING MOWER • Stop mower properly. • Place mower deck in its highest position. • If transporting without the use of a tow vehicle, then remove spark plug wire and place where it cannot contact the spark plug.
MOWER MAINTENANCE GENERAL RECOMMENDATIONS The warranty on this Trail Mower does not cover items that have been subjected to operator abuse or negligence. To receive full value from the warranty, operator must maintain unit as instructed in this manual. Some adjustments will need to be made periodically to maintain your unit properly. All adjustments in this manual should be checked at least once each season.
FRAME ASSEMBLY ITEM # QTY. PART NO. DESCRIPTION ITEM # QTY . PART NO.
CENTER BLADE DRIVER DETAIL ITEM # QTY. PART # 1 1 NB175 2 1 AS155 3 2 6114 4 1 6065PM 5 3 NB179 6 2 B98 7 4 NB690 8 1 9057* 9 4 NB524 10 1 9054 11 1 B98W 12 2 NB216 13 1 9008 14 1 20186 15 1 NB607 16 2 NB166 17 1 NB238N DESCRIPTION Nut - Jam 3/4-16 Grade 2 Washer - Belleville1.5 X .761 X .098 Pulley - 5.50" Spacer - 3/4 ID X 1-1/2 Washer - 3/4 ID X 1 1/4 OD 18 Ga Bearing Bolt - Serrt d Flange 1/4-20 X 3/4 Gr 5 Housing - Bearing Nut - Flange1/4-20 Shaft - Cent er 5.
ITEM # QTY PART NO DESCRIPTION 1 1 -See Mot or Base Det ail 2 1 -See Safet y Swit ch Bracket Det ail 3 2 -See Out er Blade Driver Det ail 4 1 -See Cent er Blade Driver Det ail 5 1 -See Grass Chut e & Spring Det ail 6 1 -See Engage Lever Det ail 7 1 -See Idler Det ail 8 2 T2PB Bushing - Plast ic 9 2 AS001 Roller - Ant i-Scalp 3/8 ID 10 1 NB707 Bolt - Carriage 3/8-16X4 11 1 NB207 Nut - Nyloc 3/8-16 12 11 NB596 Bolt - Serr Flange 5/16-18 X 3/4 13 13 NB170 Nut - Serr Flange 5/16-18 Z 14 4 26X249 Screw - .
MOTOR BASE DETAIL Slide plastic tube snug Against toggle switch. Item # 24 18057 BCSR BCLB KSK BCBT PARTS NOT SHOWN Harness - Wiring, Briggs (13-20 hp) Cable - Battery (10" Red) Cable - Battery (19 1/2"or 20" Black) Keys - For Key Switch (set of two) Boot - Rubber, Small, Battery Cable Item # 26 U1 Battery (Not Included) ITEM # 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 QTY. PART NO.
Engage Lever Detail Height Adjust Handle Detail Safety Switch & Bracket Detail ITEM # QTY. PART # DESCRIPTION ITEM # QTY. PART # DESCRIPTION ITEM # QTY .
NOTES: ______________________________________________________________________ ______________________________________________________________________ ______________________________________________________________________ ______________________________________________________________________ ______________________________________________________________________ ______________________________________________________________________ ______________________________________________________________________ ________
60” FAST FINISH TRAIL MOWER www.swisherinc.com OWNER’S MANUAL MODEL NO. FC14560BS FC14560BS-CA FC14560BSXP FC17560BS FC17560BS-CA FC17560BSXP POL14560A POL145650A-CA POL14560AEX IMPORTANT Read and follow all Safety Precautions and Instructions before operating this equipment. HOW TO ORDER REPAIR PARTS: Each mower has its own model number. Each engine has its own model number. The model number for the mower will be found at the left rear of the unit on the belt cover skirt.