swisherinc.com OWNER’S MANUAL MODEL NO. LS622 LS826 LS934 LS10534D IMPORTANT Read and follow all Safety Precautions and Instructions before operating this equipment. Rev.07.04.
SAFETY DECALS Replace decals immediately if damaged.
SEE DETAIL 1 3 A 5 13 4 6 A 8 11 25 21 26 17 FENDERS ONLY ON LS934 MODEL 8 15 6 14 20 B 10 27 2 9 7 12 B 16 22 24 22 SEE DETAIL 23 5 22 35 52 25 31 29 35 36 43 44 30 32 33 34 42 45 46 40 37 41 42 38 47 48 49 39 16 6 57 53 57 56 54 58 18 52 49 50 18 28 51 55 19 ASSEMBLY DETAIL LS622, LS826, LS934 MODELS NOT ALL PARTS ARE ON ALL MODELS
SERVICE PARTS Please have Model and Serial Numbers ready when ordering parts. Color cannot be guaranteed upon service parts.
SERVICE PARTS Pleas have Model and Serial Numbers ready when ordering parts. Color cannot be guaranteed upon service parts.
169 See Detail 121 167 129 123 120 169 168 159 118 165 166 170 119 132 163 129 164 118 133 123 162 107 160 129 127 156 155 156 158 112 141 113 129 142 134 143 154 153 109 127 126 128 110 140 110 137 139 111 144 152 138 161 111 157 122 108 107 151 145 128 131 125 116 112 131 128 149 128 171 124 117 127 146 130 147 114 124 131 128 148 124 126 136 See Detail 173 172 150 124 115 ASSEMBLY DETAIL MODEL LS10534D NOT ALL PARTS ARE ON ALL MODELS 135
SERVICE PARTS Please have Model and Serial Numbers ready when ordering parts. Color cannot be guaranteed upon service parts.
SERVICE PARTS Please have Model and Serial Numbers ready when ordering parts. Color cannot be guaranteed upon service parts. ITEM NUMBER 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 NOT SHOWN NOT SHOWN NOT SHOWN DESCRIPTION HYDRAULIC ELBOW PUMP PULLEY MOTOR BASE BELT 32.
59 60 63 61 61 64 62 65 67 73 66 68 78 69 70 79 72 75 77 80 71 81 76 81A 74 BEAM DETAIL ALL MODELS NOT ALL PARTS ARE ON ALL MODELS ITEM NUMBER 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 81A DESCRIPTION CLIP PIN STEEL PIN HYDRAULIC FITTING STATIONARY LINE ASSEMBLY RAM CYLINDER - LS622 MODEL RAM CYLINDER - LS826 MODEL RAM CYLINDER - LS934 & LS10534 MODELS 1/2-13 X 3 GR5 BOLT SPLITTING WEDGE 1/2-13 X 2 1/2 GR5 CARRIAGE BOLT RETURN LINE FITTING 1/2-13 JAM 2-WAY LOCK
82 89 90 83 84 85 ENGINE DETAIL 86 LS826, LS934, LS10534D MODELS ITEM # 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 106 NOTSHOWN NOTSHOWN 98 DESCRIPTION BLACK PLASTIC KNOB THROTTLE & CABLE(NOT SHOWN) ON - OFF KEY SWITCH GOLDEN LOCK WASHER GOLDEN KEY SWITCH NUT EXISTING ENGINE HARDWARE KEY SWITCH PLATE ENGINE 5/16-18 X 1 1/4 GR5 BOLT 5/16-18 2-WAY LOCK NUT UPPER SPACER ENGINE PULLEY LOWER SPACER BELLEVILLE WASHER 7/16-20 X 1 GR5 BOLT W/ NYLOCK KEYSTOCK WIRING HARNESS THROTTLE PLATE/ SCREWS 97 100 10
Log Splitter V-Belt Replacement • Caution! : The Idler System is spring loaded. When replacing belt, be sure to lock lever to avoid accidental release. • Remove the (6) self-tapping screws that hold the belt cover on the bottom of the unit and remove the cover to allow access to the belt. Pull clutch lever out to remove load from belt. Wedge a flat screwdriver (or something similar) into the slot to prevent release. See fig.1 Fig.1 • Fig. 2 Remove old belt.
Log Splitter V-Belt Replacement (Continued) ∀ • ∀ • ∀ • Check pulleys for alignment Check Idler for freedom of rotation Check to be sure Clutch Lever is straight and moves freely. See Fig.3 Fig.
Optional Extended Table For Log Splitter Kit No 7490 This table is designed to fit both the Standard and the Deluxe Swisher Log Splitter. The Standard attachment slips over the beam pivot tube and attaches with the hitch pin through the vertical beam lock hole. The attachment to the Deluxe Splitter requires the use of two Table Clamps (2).
Log Stripper and Table Detail 4 2 5 3 1 6 Item # 7 8 1 2 3 4 5 6 7 8 Description Log Stripper Assembly Kit Stripper Weldment 3/8-16 Nyloc Nut Stripper Spacer Stripper Bracket 3/8-16 X 5 1/2 GR5 ZP Splitter Table Accessory Kit 5/16-18 X 3/4 HCC GR2 ZP Bolt Splitter Table 5/16-18 ZP 2 Way Lock Nut Part # 7464 7444TK NB182 7449TK 7448TK NB575 7626 NB143 7621TK NB558 Log Stripper Installation Instructions 1. Turn off engine and disconnect spark plug wire.
Models LS622 LS8526 LS934 LS10534D Splitting Force 22 Tons 26 Tons 34 Tons 34 Tons Engine 6 Hp Briggs and Stratton Quantum 8.5 HP Briggs and Stratton 9 HP Briggs and Stratton I/C 10.
LOG SPLITTER OWNER’S MANUAL MODEL NO. LS622 LS826 LS934 LS10534D HOW TO ORDER REPAIR PARTS: Each Log Splitter has its own serial number. Each engine has its own serial number. The serial number for the Log Splitter will be found on the right hand side of the hydraulic oil reservoir. The serial number for the engine will be found on the top of the blower fan housing. All Log Splitter parts listed herein may be ordered directly from Swisher Mower & Machine Co. Inc.