OWNER’S MANUAL STARTING SERIAL #: 99-307001 MODEL NO. T1260 T1360 T1460 60” UNIVERSAL TRAILMOWER IMPORTANT Read and follow all Safety Precautions and Instructions before operating this equipment. Rev.04-288 Assembly Operation Service and Adjustment Repair Parts P.O.
LIMITED WARRANTY The manufacturer’s warranty to the original consumer purchaser is: This product is free from defects in materials and workmanship for a period of one (1) year from the date of purchase by the original consumer purchaser. We will repair or replace, at our discretion, parts found to be defective due to materials or workmanship.
SAFETY PRECAUTIONS This Safety Alert Symbol indicates important messages in this manual. When you see this symbol, carefully read the message that follows and be alert to the possibility of personal injury. Read this manual completely. This machine can amputate hands, feet, and throw objects. Failure to observe the following safety instructions could result in serious injury or death. • Read the manual. Learn to operate this machine safely.
• T u r n o f f t h e b l a d e s w h e n n o t m o w i n g . B e f o r e l e a v i n g t h e m a c h in e , t u r n o f f t h e b l a d e s a n d s to p th e e n g in e . • W a t c h f o r tr a f f ic w h e n o p e r a t i n g n e a r o r c r o s s i n g r o a d w a y s . • D o n o t o p e ra te th e m o w e r if it h a s b e e n d ro p p e d o r d a m a g e d in a n y m a n n e r o r if th e m o w e r v i b r a t e s e x c e s s iv e l y .
REQUIRED ASSEMBLY FRONT WHEEL CASTER ASSEMBLY 1. Remove single nut and washers from caster shaft. 2. Place one washer on the shaft of the caster/wheel sub-assembly. 3. Slide same shaft through the bearing/frame with wheel towards the ground. 4. Place the other washer on the shaft; it should be resting on the top bearing. 5. Thread nyloc jam nut onto shaft. 6. Tighten nut snuggly, making sure shaft threads enter the nyloc of the nut. Overtightening of this nut will bind caster. 7.
OPERATING YOUR TRAILMOWER The operation of any mower can produce foreign objects to be thrown into the eyes, resulting in severe eye damage. Always wear certified safety glasses or wide-vision safety goggles over spectacles before staring any cutting machine and while operating such a machine. The operation of any cutter produces sound waves that are damaging to the human ear. Ear protection is recommended. CAUTION! Tragic accidents can occur if the operator is not alert to the presence of children.
• • • • • • • • Make sure the tow vehicle parking brake is set, mower is level, and blades are disengaged. Check spark plug wire, oil, and fuel. Check all electrical connections (See Schematics). Make sure toggle switch is turned “ON” and the red tether is properly attached. Set engine idle to “CHOKE” position. With feet clear of mower deck, turn key switch to the “START” position; [ if unit is equipped with 12 volt system ] release when engine begins to run.
ALTERNATIVE STOPPING METHOD • Bring vehicle to complete stop, shut off engine, and set parking brake. • Disengage blade engage lever (681N). • Manually shut toggle and key switches to their “OFF” positions. • Always remember to remove keys to avoid irresponsible usage. TRANSPORTING MOWER • Stop mower properly. • Place mower deck in its highest position. • If transporting unattached from tow vehicle, then remove spark plug wire and place where it cannot contact the spark plug.
MOWER MAINTENANCE GENERAL RECOMMENDATIONS The warranty on this Trailmower does not cover items that have been subjected to operator abuse or negligence. To receive full value from the warranty, operator must maintain unit as instructed in this manual. Some adjustments will need to be made periodically to maintain your unit properly. All adjustments in this manual should be checked at least once each season. BEFORE EACH USE • Check engine oil level on a level surface.
NB122 NB126 NB195 NB149 664N F4157WF Figure 01 Figure 02 H11 H10TK H10TK 661 H11 Figure 03 H11 661A 661 CH5S NB136 NB181 6031TK steel chute replaces plastic chute shown Figure 04 10 662
02 03 04 05 06 08 07 SERIAL NUMBER 01 13 08 10 09 11 12 02 Figure 05 Item # 1 2 3 4 5 6 7 Description Grass Chute Bolt/Nut Spring Tire/Wheel/Bearing Right Belt Guard Acorn Nut No Step Decal Height Adjust Assembly Plastic Bushing Ruler Decal Eye Bolt Knob 5/16 Pal Nut Left Belt Guard Acorn Nut Gas Tank Gas Cap Gas Tank Mount Rubber Bushing Fuel Shutoff Valve Fuel Line Hose Clamp Fuel Line Part # 6031TK NB136/NB181 CH5S F4157W 6155RN NB120 OD11 H7N T2PB OD41 6599 H7K NB276 6155LN NB120 6102
15 23 29 15 17 16 14 18 28 LEFT RIGHT 28 16 REAR 26 27 21 16 29 18 19 20 25 22 27 KEY SWITCH 24 FRONT Figure 06 Item # 14 15 16 17 18 19 20 21 Description Clutch Idler Rod/Spring Idler Rod/Spring Idler Pulley Clutch Idler Arm Idler Bracket Throttle Decal Blade Driver Center Blade Driver Right Part # 3123TK/682S 6704TK/682S B527 6709TK 6681TK OD58 9084 9085 Item # Description 22 Blade Driver Left 23 Deck 24 Warning Serious Injury Decal 25 5 MPH Decal 26 Caution - Deflector Decal 27 6
31 31 31 31 31 32 30 26 31 Figure 07 Item # 30 31 32 Description Blade (3) Anti-Scalp Roller Rear Axle Part # 9004 AS001 664N MIDDLE CENTER BLADE DRIVER PULLEY BELT 66LR2 LEFT RIGHT BOTTOM CENTER BLADE DRIVER PULLEY BELT 66LR2 TOP CENTER BLADE DRIVER PULLEY REAR ENGINE PULLEY BELT 644 ENGINE PULLEY BELT CONFIGURATION 13
ENGINE 689L 9031 688 689S 699 NB452N (Briggs & Honda) NB238N (Tecumseh) Not Shown OIL DRAIN VALVE + CAP AS122, AS123 ENGINE PULLEY ASSEMBLY 14
BLADE DRIVER ASSEMBLIES EFFECTIVE AFTER SERIAL# L199307001 NB175 6114 AS155 6114CS NB179 9091TK (re-enforcement will vary from what is shown) B98 9075 shaft replaces both the 9002 shaft & 9010 spacer B98 NB179 9008 NB216 RIGHT NB175 AS155 6114 9004 NB179 NB166 NB607 NB607 B98 NB238N CENTER 9077 shaft replaces both the 9000 shaft and the 9010 spacer B99TK B98 9008 NB179 NB216 9004 NB607 NB238N NB166 15
LEFT NB175 6114 AS155 6104RS B98 9078 shaft replaces both the 9001 shaft and the 9010 spacer B99TK NB179 B98 NB216 9008 9004 NB607 NB238N NB166 16
ELECTRIC START WIRING SCHEMATIC ATTACH RED TETHER HERE HONDA WIRING SCHEMATIC ATTACH RED TETHER HERE 17
Items Not Shown Item Wiring Harness (Briggs) Wiring Harness (Tecumseh) Wiring Harness (Honda) Solenoid Frame Caster Bearings Key Switch Battery Cable - Red Battery Cable - Black Engine Belt Blade Driver Belts 18 Part # WHN60B WHN60T WHN60H 9043 B98 KS12 BCSR BCS 644 66LR2
NOTES 19
60” UNIVERSAL TRAILMOWER OWNER’S MANUAL MODEL NO. T1260 T1360 T1460 HOW TO ORDER REPAIR PARTS: Each mower has its own model number. Each engine has its own model number. The model number for the mower will be found on the right hand side of the frame above the right rear wheel. The model number for the engine will be found on the top of the blower fan housing. All mower parts listed herein may be ordered directly from Swisher Mower & Machine Co. Inc. or your nearest Swisher dealer.