www. swisherinc.com OWNER'S MANUAL STARTING SERIAL #: L106-038001 MODEL NO. T1360B1 T1360T T1360H T1360K T13560 RK1360 T14560 60" FINISH CUT TRAILMOWER T17560 T18560 ! _ OF QUALITY SINCE 1945 f IMPORTANT Read and follow all Safety Precautions and Instructions before operating this equipment. Rev 07-151 P.O.
LIMITED The manufacturer's warranty to the original WARRANTY consumer is free from defects in materials and workmanship from the date of purchase by the original consumer replace, at our discretion, workmanship. exclusions: l) Engine parts This warranty found is: for a period purchaser.
SAFETY This Safety manual. follows Read objects. injury • • • this manual Failure Alert Symbol PRECAUTIONS indicates important When you see this symbol, and be alert to the possibility completely. to observe This machine the following in this carefully read the message of personal injury. can amputate safety messages instructions hands, could feet, result / that I | J and throw in serious or death. Read the manual. Learn to operate this machine safely.
WARRANTY YOUR WARRANTY evaporative RIGHTS emission control AND system RIGHTS OBLIGATIONS: (EECS) The California AND OBLIGATIONS Air Resources Board on your model year 2006 and later Swisher and Swisher Product. Mower, In California, is pleased to explain new Outdoor Power the Equipment, nmst be designed, built and equipped to meet the State's stringent anti-smog standards.
SAFETY DECALS Replace decals immediately if damaged.
REQUIRED FRONT 1. 2. 3. 4. 5. 6. 7. REAR 1. 2. 3. 4. OFFSET 1. 2. 3. 4. 5. WHEEL CASTER ASSEMBLY ASSEMBLY Remove single nut and washers from caster shaft. Place one washer on the shaft of the caster/wheel sub-assembly. Slide same shaft through the bearing/frame with wheel towards the ground. Place the other washer on the shaft; it should be resting on the top bearing. Thread nyloc jam nut onto shaft. Tighten nut snuggly, making sure shaft threads enter the nyloc of the nut.
OPERATING YOUR TRAILMOWER The operation of any mower can produce foreign objects to be thrown into the eyes, resulting in severe eye damage. Always wear certified safety glasses or wide-vision safety goggles over spectacles before staring any cutting machine and while operating such a machine. The operation of any cutter produces sound waves that are damaging to the human ear. Ear protection is recommended. CAUTION! Tragic accidents can occur if the operator is not alert to the presence of children.
• • • • • • • • Makesurethetow vehicleparkingbrakeis set,moweris level, andbladesare disengaged. Checksparkplug wire, oil, andfuel. Checkall electricalconnections(SeeSchematics). Makesuretoggleswitchis turned"ON" andthe redtetheris properlyattached. Setengineidle to "CHOKE" position. With feetclearof mowerdeck,turn key switchto the "START" position; [ if unit is equippedwith 12volt system] releasewhenenginebeginsto run.
ALTERNATIVE STOPPINGMETHOD • • • • Bring vehicle to complete stop, shut off engine, and set parking brake. Disengage blade engage lever (6008). Manually shut toggle and key switches to their "OFF" positions. Always remember to remove keys to avoid irresponsible usage. TRANSPORTING MOWER • Stop mower properly. • Place mower deck in its highest position. • If transporting unattached from tow vehicle, then remove spark plug wire and place where it cannot contact the spark plug.
MOWER GENERAL MAINTENANCE RECOMMENDATIONS The warranty on this Trailmower does not cover items that have been subjected to operator abuse or negligence. To receive lull value from the warranty, operator must maintain unit as instructed in this manual. Some adjustments will need to be made periodically to maintain your unit properly. All adjustments in this manual should be checked at least once each season. BEFORE EACH USE • • Check Check engine oil level on a level surface.
Description Swivel Hitch Frame 14 15 16 17 18 19 20 21 Detail 19 Housing Tube 5/16 PAL Nut H10 12513* B98 NB126 6034 H7N H7N1TK NB276 22 23 24 Plastic Knob Crank Arm 5/8 ID X 10D 14 Ga Washer H7K ES214 NB 149 25 26 NS 5/8 IDX10D Bearing Cotter Pin Rear Axle Height Adjustment Handle USE PAINT tem No, 1 2 Description Tongue Hitch Solid Stock Hitch Part # 66!* 661A* 3 4 Bushing Safety Hitch Pin 10579 H11 5 6 7 8 Caster/Wheel Assembly 3/4 - 16 Nyloc Nut Caster Fork Was her 9 Wheel Spacer 6
GAS TANK ASSEMBLY TANK ASSEMBLY PART# ELNIT MODEL -- POL14560B POL14560C RK1360 T13560 T13560B1 T1360T T17560 -- "-12 T1360B1 #6059H-- T1360H #6080 T1360K MOWER DECK DETAIL Description Belt Cover Grass Chute Part# 6025TK 6039TK Chute Bracket 6O30TK AS001 Anti-Scalp Roller Deck 6027* 9100 6102NC Chute Spring Gas Cap Gas Tank 6102T Tank Bracket Hitch Pin Tank Stand 6078TK Hll 6044TK Sway Bar Left 3665 3664 Sway Bar Right Deck Idler 3/8 - 16 X1 1/4 Bolt BELT TENSION IDLER DETAIL 605
MOTOR BASE DETAIL Slide plastic tube snug against toggle switch.
ENGINE DETAIL BRIGGS / TECUMSEH > DETAIL- 1 DETAILItem No. l I Description UPPER SPACER 2 3 5-1/2" ENGINE PULLY 1/4/X 1" KEY STOCK 4 5 LOWER SPACER 3/6 BELLEVILLE WASHER 6 FLAT WASHER 7 3/6-24 X 1 BOLT [BRIGGS ] 7/16-20 X 1 BLOT [TECUMSEH 5/16-16 X I-3/4 BOLT 8 9 5/16u ] ......................................... ........ _gi% ....... ................................................................................... ................................................. 11 BELT GUIDE ......
HONDA 12V SCHEMATICS RECTIFIER TECUMSEH RED WIRING BATTERY 12V BATTERY LARGE RED PLUGS LARGE RED RED r HONDA SOLENOID The Honda RED _: _i_o the starter i t and comes w_h Ct_heengine.
f 60" FINISH CUT TRAILMOWER www.swisherinc.com OWNER'S HOW TO ORDER REPAIR PARTS: MANUAL Each mower has its own model number. Each engine has its own model number. The model number for the mower will be MODEL T1360B1 T1360T T1360H T1360K T13560 RK1360 T14560 T17560 T18560 NO. f\mnd on the right hand side of the fiame at the wheel bracket. The model number f\3r the engine will be found on the top of the blower tan housing.
