www.swisherinc.com OWNER’S MANUAL STARTING SERIAL # L101-344001 MODEL NO. T1360B1 T1360T T1360H T1360K T13560 RK1360 T14560 T17560 60” FINISH CUT TRAILMOWER IMPORTANT Read and follow all Safety Precautions and Instructions before operating this equipment. Rev: 05-007 Assembly Operation Service and Adjustment Repair Parts PHONE 660-747-8183 FAX 660-747-8650 Made In The Manufacturing quality lawn care equipment since 1945 USA P.O.
LIMITED WARRANTY The manufacturer’s warranty to the original consumer purchaser is: This product is free from defects in materials and workmanship for a period of one (1) year from the date of purchase by the original consumer purchaser. We will repair or replace, at our discretion, parts found to be defective due to materials or workmanship.
SAFETY PRECAUTIONS This Safety Alert Symbol indicates important messages in this manual. When you see this symbol, carefully read the message that follows and be alert to the possibility of personal injury. Read this manual completely. This machine can amputate hands, feet, and throw objects. Failure to observe the following safety instructions could result in serious injury or death. • Read the manual. Learn to operate this machine safely.
• Turn off the blades when not mowing. Before leaving the machine, turn off the blades and stop the engine. • Watch for traffic when operating near or crossing roadways. • Do not operate the mower if it has been dropped or damaged in any manner or if the mower vibrates excessively. Excessive vibration is an indication of damage. Repair mower as necessary. • Dress properly. Do not operate the mower when barefoot or wearing open sandals. Wear only solid shoes with good traction when mowing.
SAFETY DECALS Replace decals immediately if damaged.
REQUIRED ASSEMBLY FRONT WHEEL CASTER ASSEMBLY 1. Remove single nut and washers from caster shaft. 2. Place one washer on the shaft of the caster/wheel sub-assembly. 3. Slide same shaft through the bearing/frame with wheel towards the ground. 4. Place the other washer on the shaft; it should be resting on the top bearing. 5. Thread nyloc jam nut onto shaft. 6. Tighten nut snuggly, making sure shaft threads enter the nyloc of the nut. Overtightening of this nut will bind caster. 7.
OPERATING YOUR TRAILMOWER The operation of any mower can produce foreign objects to be thrown into the eyes, resulting in severe eye damage. Always wear certified safety glasses or wide-vision safety goggles over spectacles before staring any cutting machine and while operating such a machine. The operation of any cutter produces sound waves that are damaging to the human ear. Ear protection is recommended. CAUTION! Tragic accidents can occur if the operator is not alert to the presence of children.
• • • • • • • • Make sure the tow vehicle parking brake is set, mower is level, and blades are disengaged. Check spark plug wire, oil, and fuel. Check all electrical connections (See Schematics). Make sure toggle switch is turned “ON” and the red tether is properly attached. Set engine idle to “CHOKE” position. With feet clear of mower deck, turn key switch to the “START” position; [ if unit is equipped with 12 volt system ] release when engine begins to run.
ALTERNATIVE STOPPING METHOD • Bring vehicle to complete stop, shut off engine, and set parking brake. • Disengage blade engage lever (6008). • Manually shut toggle and key switches to their “OFF” positions. • Always remember to remove keys to avoid irresponsible usage. TRANSPORTING MOWER • Stop mower properly. • Place mower deck in its highest position. • If transporting unattached from tow vehicle, then remove spark plug wire and place where it cannot contact the spark plug.
MOWER MAINTENANCE GENERAL RECOMMENDATIONS The warranty on this Trailmower does not cover items that have been subjected to operator abuse or negligence. To receive full value from the warranty, operator must maintain unit as instructed in this manual. Some adjustments will need to be made periodically to maintain your unit properly. All adjustments in this manual should be checked at least once each season. BEFORE EACH USE • Check engine oil level on a level surface.
NB149 - WASHER IF NECESSARY 19 7 FRAME DETAIL 18 NB177 665TC USE PAINT CODE: TC=RED, TK=BLACK Outer Blade Driver Configuration 17 EX: 6014TC,6014TK 11 8 Blade Driver Assy. 19 4 2 9058- 5.75” (Center Shaft) 9018- 4.25” (Outer Shafts) 7 Item No.
GAS TANK ASSEMBLY TANK ASSEMBLY PART # / UNIT MODEL #6059 POL14560B POL14560C RK1360 T13560 T13560B1 T1360T T17560 T1360B1 #6059H T1360H #6080 T1360K Not shown WASHER [ NB 170] MOWER DECK DETAIL 6027* 6044TK BELT CONFIGURATION 5058 (Long) 6046 (Short) TZ2S USE PAINT CODE: TC=RED, TK = BLACK EX: 6060TC, 6060TK 12
Slide plastic tube snug against toggle switch.
ENGINE DETAIL BRIGGS / TECUMSEH > DETAIL - 1 DETAIL - 1 Item No. Description Part # 1 2 3 4 5 6 7 UPPER SPACER 5-1/2'' ENGINE PULLY 1/4/ X 1'' KEY STOCK LOWER SPACER 3/8 BELLEVILLE WASHER FLAT WASHER 3/8-24 X 1BOLT [BRIGGS ] 7/16-20 X 1 BLOT [TECUMSEH ] 5/16-18 X 1-3/4 BOLT 5/16 USS WASHER 5/16-18 Flge NUT BELT GUIDE 5/16-18 X 1 1/4 FLG.
WIRING SCHEMATICS HONDA ENGINES KOHLER ENGINES IGNITION SWITCH BATTERY POSITIVE CABLE 15
60” FINISH CUT TRAILMOWER www.swisherinc.com OWNER’S MANUAL MODEL NO. T1360B1 T1360T T1360H T1360K T13560 RK1360 T14560 T17560 HOW TO ORDER REPAIR PARTS: Each mower has its own model number. Each engine has its own model number. The model number for the mower will be found on the right hand side of the frame at the wheel bracket. The model number for the engine will be found on the top of the blower fan housing. All mower parts listed herein may be ordered directly from Swisher Mower & Machine Co. Inc.