www.swisherinc.com OWNER'S MANUAL STARTING SERIAL #: LI I2-121001 MODEL NO. T14560A T14560B T18560A T18560B T14560A-CA 60" FINISH CUT TRAILMOWER T14560B-CA T18560A-CA T18560B-CA T14560AEC T18560AEC A T_OITION OF OUALIT¥ SINCE 194S _IMPORTANT Read and follow all Safety Precautions and Instructions before operating equipment. this J 1602 Corporate Dr.
LIMITED WARRANTY The manufacturer's warranty to the original consumer purchaser is: This product is free from defects in materials and workmanship for a period of one (1) year from the date of purchase by the original consumer purchaser. As required by § 1060.120, the fuel system related components, which have been certified to this equipment by SAI are to be free of defects in material and workmanship for a period of two (2) years from the date of purchase by the original consumer purchaser.
SAFETY PRECAUTIONS -%, I This Safety manual. follows Read objects. injury this manual Failure Alert When and completely. to observe Symbol indicates you see this symbol, be alert This to the possibility machine the following important carefully read of personal can amputate safety messages hands, instructions could in this the message / tha injury. feet, and result j throw in serious or death. • • Read the manual. Learn to operate this machine safely.
WARRANTY RIGHTS AND OBLIGATIONS YOUR WARRANTY RIGHTS AND OBLIGATIONS: The California Air Resources Board and Swisher are pleased to explain the evaporative emission control system (EECS) on your model year 2006 and later Swisher Product. hi California, new Outdoor Power Equipment, nmst be designed, built and equipped to meet the State's stringent anti-smog standards.
SAFETY DECALS Replace decals inmlediately if damaged. Order by part number from Swisher.
REQUIRED FRONT 1. 2. 3. 4. 5. 6. 7. 8. 9. REAR 1. 2. 3. 4. 5. WHEEL CASTER ASSEMBLY ASSEMBLY Remove single nut and washers from caster shaft. Place one washer on the shaft of the caster/wheel sub-assembly. Slide same shaft through the bearing/flame with wheel towards the ground. Place the other washer on the shaft; it should be resting on the top bearing. Add thin washer (17x195). Thread nylocjam nut onto shaft. Tighten nut snuggly, making sure shaft threads enter the nyloc of the nut.
OPERATING YOUR TRAILMOWER f The operation of any mower can produce foreign objects to be thrown into the eyes, resulting in severe eye damage. Always wear certified safety glasses or wide-vision safety goggles over spectacles before starting any cutting machine and while operating such a machine. J The operation of any cutter produces sound waves that are damaging human ear. Ear protection is recommended.
. Make . Check spark plug wire, oil, and fuel. . Check all electrical . Make . Set engine . With feet clear of mower deck, turn key switch to the "START" position; equipped with 12 volt system) release when engine begins to run. . For units NOT equipped rope until engine starts. with electric . Set engine RPM.
ALTERNATIVE STOPPING METHOD ,, Bring vehicleto completestop,shutoff engine,andsetparkingbrake. ,, Disengagebladeengagelever(17611). ,, Manuallyshuttoggleandkey switchesto their "OFF" positions. ,, Alwaysrememberto removekeysto avoid irresponsibleusage. TRANSPORTING . . . Stop mower properly. Place mower deck in its highest position. If transporting unattached from tow vehicle, then remove where it cannot contact the spark plug. SUGGESTED . . . . . . . . . .
MOWER GENERAL MAINTENANCE RECOMMENDATIONS The warranty on this Trailmower does not cover items that have been subjected to operator abuse or negligence. To receive full value from the warranty, operator must maintain unit as instructed in this manual. Some adjustments will need to be made periodically to maintain your unit properly. All adjustments in this manual should be checked at least once each season.
FRAME ASSEMBLY i ITEM# 1 QTY. PART NO DESCRIPTION 1 3664 Bar - Right Sway ITEM # QTY. 2 1 3665 3 4 1 2 5 1 Bar - Left Sway 17600TC Weldment -T60 Frame F4157WK Wheel/Tire 5/8" Bearing 13/5/6 NHS; BIk 662TC Weldment - Tongue Offset Extension 6 7 1 1 661ATC 661TC 8 2 -- Weldment - Solid Stock Hitch Weldment - Tongue Hitch Extension See Cast er/Wheel Assembly Detail PART NO.
CENTER ITEM# BLADE DRIVER DETAIL QTY. PART NO. DESCRIPTION 1 1 9057TK Housing-Bearing 2 4 NB690 Bolt - Serrtd Flange 3 4 2 1 B98 9054 5 3 NB179 Washer-3/41DX1 6 1 B98W Washer - Flat 3/4 ID X 1 3/40D 7 2 6114 Pulley- 5.50" 8 1 6065PM Bearing Shaft - Center 1/4-20 X 3/4 Gr 5 5.75" 1/4OD18Ga Spacer-3/41DXl-1/2 9 1 AS155 Washer - Belleville1.5 10 1 NB175 Nut - Jam 3/4-16 Grade X .761 X .
ITEM 1 2 3 MOWER DECK DETAIL ITEM# QTY, PART NO, 1 1 166X34 Spring 2 1 NB182 Nut-Nyloc3/8-16zy 3 1 NB784 4 1 092100 Or7 PART NO 1 -- DESCRIPTION See Motor Base Detail 1 -- 2 -- See Safetv Switch Bracket Detail See Outer Blade Driver Detail 4 5 1 -- See Center 1 -- See Grass Chute & Sprinq Detail 6 7 1 -- 1 -- See Enplaple Lever Detail See Idler Detail 8 9 10 2 2 1 T2PB AS001 NB707 Bushinq - Plastic 11 12 1 11 NB207 NB596 Nut - Nyloc 3/8-16 Bolt - Serr Flanqe
MOTOR BASE DETAIL Slide plastic tube snug Against toggle switch. Item # 24 I I I Item # 26 I Battery shown representation is for only PARTS NOT SHOWN 18057 Harness - Wiring, Battery Briggs ( 13-20 hp) (BCI Group # : U 1R) BCSR Cable - Battery (10" Red) BC LB Cable - Battery (19 1/2"0r 20" Black) KSK Keys - For Key Switch BCBT i ITEM# 1 Boot - Rubber, QTY. (set of two) Small, Battery Cable PART NO.
Engage IITEM# QTY, PART# 1 2 1 2 NB199 NB280 3 1 18389TK 4 5 6 1 1 1 NB170 NB253 NB181 7 8 1 2 4578TK 10177 9 1 11158 Lever Detail Height Adjust Handle DESCRIPTION ITEM# Bolt- 3/8-16X5HCCGR5ZP Nut - 2 Way Lock 3/8-16 ZY Engage - Weldment Nut - Serr Flng 5/16-18 Bolt-SerrFIng,5/16-18X1 Nut - Nyloc 5/16-18 Pivot - Engage Washer-Fender3/8X1 1/4 QTY, PART# Detail & Bracket PART# DESCRIPTION Detail Adjust 1 1 18390TK Mount - Switch 2 1 3695 Switch - NormallyCIosed 3 2
f 60" FINISH CUI www.swisherinc.com TRAILMOWER OWNER'S MANUAL MODEL HOW TO ORDER REPAIR PARTS: Each mower has its own model number. Each engine has its own model number. The model number for the mower will be found at the left rear of the unit on the belt cover skirt. The model number for the engine will be found on the top of the blower fan housing. All mower parts listed herein may be ordered directly from Swisher or your nearest Swisher dealer.