Versa – Tractor Commercial Pro Land Management System Model #: VT389H Description: Versa Tractor, 389cc Honda SWISHER ACQUISITION INC.
TABLE OF CONTENTS LIMITED WARRANTY 3 INTRODUCTION 4 FEATURES .
LIMITED WARRANTY The manufacturer’s warranty to the original consumer purchaser is: This product is free from defects in materials and workmanship for a period of three (3) years for residential use and one (1) year for commercial use from the date of purchase by the original consumer purchaser. We will repair or replace, at our discretion, parts found to be defective due to materials or workmanship.
INTRODUCTION Congratulations! Thank you for purchasing Swisher’s Versa Land Management System. With this versatile system you will be able to tackle all of your toughest jobs in all seasons. This manual is a valuable document. Following the instructions for use, service, maintenance, etc. can greatly increase the performance and life of your machine.
FEATURES щ 1 2 3 4 5 6 7 8 9 Adjustable Stabilizer Bars Control Levers Control Panel Battery (UL1 Type) Brake / Brake Release Hitch Hydraulic Oil Cooler Belt Covers Quick Attatch Pin 10 11 12 13 14 15 16 17 18 5 Power Unit Stand PTO Drive Hydraulic Reservoir Engine All-Terrain Drive Tires Sulky Fuel Tank Ignition Switch Locking Collar
CONTROLS ǘ慆 1 2 3 4 Directional Controls-Left Wheel Directional Controls-Right Wheel Adjustable Stabilizer Bars Digital Hour Meter 5 6 7 8 Throttle Control PTO Engage/Disengage Emergency Shut Off Engine Choke Control Note: Refer to the Operating Instructions on page 13-15 for complete directions on operating the unit.
SAFETY INSTRUCTIONS These instructions are for your safety. Read them thoroughly & carefully. This Safety Alert Symbol indicates important messages in this manual. When you see this symbol, carefully read the message that follows and be alert to the possibility of personal injury. General Use: Read all instructions in this operator’s manual and on the machine before starting it. Ensure that you understand them and then abide by them.
SAFETY INSTRUCTIONS These instructions are for your safety. Read them thoroughly & carefully. This Safety Alert Symbol indicates important messages in this manual. When you see this symbol, carefully read the message that follows and be alert to the possibility of personal injury. Training: All users should seek and obtain professional and practical instruction. Such instruction should emphasize: Children: Children are often attracted to power equipment.
SYMBOLS & DECALS This Safety Alert Symbol indicates important messages in this manual. When you see this symbol, carefully read the message that follows and be alert to the possibility of personal injury.
Uncrating Instructions Tools Required: • Tire pressure gauge • Nail bar or claw hammer • Wire snips • Protective eyewear To remove the tractor from the crate: Position crate on a flat, level surface Dispose of top and side panels of the crate. Remove packing material. Cut any banding or strapping that may be holding the tractor to the crate. Disconnect the spark plug wire and place where it cannot make a connection. Remove and dispose of all wheel chalks that are holding the machine in place.
CUSTOMER RESPONSIBILITIES V-Belts: WARNING Check V-belts for deterioration and wear before each use and replace if necessary. Replace belts if they begin to slip from wear. Refer to Quick Reference and Service & Adjustment sections of this manual for instructions on belt part numbers and how to properly replace belts.
CUSTOMER RESPONSIBILITIES Specifications PTO DRIVE Electric Magnetic Clutch ARTICULATION DIRECTION(S) Front to Back & Side to Side TIRE SIZE 18 X 850 -10 w/ 4X4 Lug TIRE PRESSURE 40 PSI Max BATTERY 12V / Heavy Duty 340 CCA / Type U1L HYDRAULIC FLUID 20W50 Oil ENGINE OIL SAE 30 W UNIT MEASUREMENTS LENGTH: WIDTH: HEIGHT: WEIGHT: 47” 35.5” 47.
OPERATION Starting: PTO Operation Before starting the tractor, be sure the area is clear of any people or animals. Control handles must be in the neutral lockout position. • Emergency shut-off switch must be in the upright position PTO switch must be in the disengaged position (pushed down). Turn ignition key until engine starts. If the engine struggles to start, engage the choke until the engine fires, then disengage the choke before operating.
OPERATION Connecting and Disconnecting Implements Always make sure that the tractor and attachment are both on flat ground before attempting to connect or disconnect the units. Always check that there are no children around that can be harmed when connecting or disconnecting units. Always check that there are no other persons around the immediate area that could potentially activate the tractor. Connecting 1. 2. 3. 4. 5. Remove any covering necessary on the attachment.
OPERATION Controls Be familiar with all controls, their functions and how to operate them before starting the machine. Motion control levers on each side control the direction of movement. SEE FIGURE BELOW When operating use smooth, controlled movements on the control handles. Using quick, erratic movements can cause the machine to become out of control.
SERVICE & ADJUSTMENTS INCREASE FORWARD SPEED Adjusting Travel Speed and Drive Tracking Both the front (A) and rear (B) stabilizer bars a can be adjusted inward and outward to obtain a greater ground speed or restrict ground speed in both forward and reverse travel by loosening the mounting bolts (C). After desired setting is applied make sure the mounting bolts are tightened.
SERVICE & ADJUSTMENTS WARNING Belt Adjustment and Reference To remove or install either belt the front cover (page 35) and clutch stop assembly (page 23) must be removed STOP THE ENGINE AND DISCONNECT THE SPARK PLUGS BEFRE MAKING ANY ADJUSTMENTS TO THE MACHINE! PTO Shaft Before every use, check to make sure the PTO shaft is securely attached to both the tractor and attachment gearboxes. Before every use, check the PTO shaft u-joints to make sure they are not damaged or worn.
TROUBLESHOOTING Problem Engine Will Not Turn Over Excessive Vibration Cause Correction 1. 2. 3. Control levers not in neutral position. Battery is undercharged or failing. Circuit breaker on engine tripped. 1. 1. 2. Worn, bent or loose PTO Adapter. Loose hardware on PTO shaft. 1. 2. 3. 2. Make sure control levers are in the middle of their travel. Charge or replace the battery. Reset circuit breaker at engine. Replace PTO adapter; Tighten PTO adapter bolts.
POWER UNIT IDENTIFICATION Power Unit Identification Unauthorized Replacement Parts Each mower has its own model number and serial number. The number for the attachment can be found on the motor base (refer to Symbols & Decal section for reference). All mower parts listed herein may be ordered directly from Swisher or your nearest Swisher dealer. Use only Swisher replacement parts.
REPLACEMENT PARTS Quick Reference Swisher Part # Part Description 21560 Belt - V; 1/2" X 48" 20846 Belt - Wrapped, 34.5" 21513 Shaft - PTO, 6E Drive 21514 Tire/Wheel - 18 X 850-10 21556 Filter - Hydro Gear, 25 Micron 21550 Hose - 3/8" ID(SEE PARTS BREAKDOWN FOR INDIVIDUAL LENGTHS) 21547 Hose - Hyd, 1/2" X 15" (2) FMLE JIC 3/4" AS069 Electrical - 10 綀ёAmp Fuse 21525 Collar - Pivot H11 Pin - Safety Hitch 3/8 X 2 1/2 ZY CAUTION Use extreme care when working on machinery.
ENGINE ASSEMBLY ⿰ь When Ordering Replacement Parts: * = USE PAINT CODE: TK=BLACK 21
PUMP / PUMP MOUNT ASSEMBLY ǘ뱆߾ع When Ordering Replacement Parts: * = USE PAINT CODE: TK=BLACK 22
PUMP / PUMP MOUNT ASSEMBLY ɦ쩆߾ع CLUTCH STOP ASSEMBLY When Ordering Replacement Parts: 23 * = USE PAINT CODE: TK=BLACK
SHAFT / CLUTCH ASSEMBLY GREASE POINTS ǘ졆߾ع When Ordering Replacement Parts: * = USE PAINT CODE: TK=BLACK 24
IDLER ASSEMBLIES ʽ慆 When Ordering Replacement Parts: * = USE PAINT CODE: TK=BLACK 25
WHEEL MOTORS LOWER MOTOR BASE ˊ但 When Ordering Replacement Parts: 26 * = USE PAINT CODE: TK=BLACK
UPPER MOTOR BASE ʽ浆 When Ordering Replacement Parts: 27 * = USE PAINT CODE: TK=BLACK
CONTROLS / CONTROL TOWER ˊ孆 When Ordering Replacement Parts: * = USE PAINT CODE: TK=BLACK 28
CONTROLS / CONTROL TOWER Ȁ祆 When Ordering Replacement Parts: 29 * = USE PAINT CODE: TK=BLACK
CONTROLS / CONTROL TOWER ˊ杆 When Ordering Replacement Parts: * = USE PAINT CODE: TK=BLACK 30
CONTROLS / CONTROL TOWER B Ȁ蕆柰ю When Ordering Replacement Parts: * = USE PAINT CODE: TK=BLACK 31
OIL COOLER ˊ獆 When Ordering Replacement Parts: * = USE PAINT CODE: TK=BLACK 32
MAIN ASSEMBLY Ȁ酆柰ю When Ordering Replacement Parts: * = USE PAINT CODE: TK=BLACK 33
KICKSTAND / BRAKE ASSEMBLIES ˊ罆 When Ordering Replacement Parts: * = USE PAINT CODE: TK=BLACK 34
COVERS / DRIVE TIRES Ȁ鵆柰ю When Ordering Replacement Parts: * = USE PAINT CODE: TK=BLACK 35
•CONNECTORS SHOWN FROM WIRE ENTRY END ˊ譆߾ع ELECTRICAL SYSTEM WIRING HARNESS 21570
HYDRAULIC SYSTEM 0 37
NOTES ˊ鑆߾ع 38
NOTES 縀ю 39
SWISHER HISTORY Back before electricity came to rural Missouri Max Swisher was producing lawn mowers from his mother’s chicken house. Max never liked to mow grass. He installed a gearbox on his family’s lawn mower creating a self-propelled unit. By tying one end of a rope to the mower and the other end to a tree in the center of the yard the mower circled the tree, shortening the rope and guiding the mower in concentric circles. Max enjoyed relaxing under a shade tree while his invention did all the work.
