OWNER’S MANUAL swisherinc.com FOR MODELS – WRC10224HC, WRC10224H, WRC11524BSC, WRC11524BS STARTING SERIAL #: L118-335001 24” WALK BEHIND Rough Cut Trail Cutter RECOIL AND ELECTRIC START MODELS PREDATOR TALON COMMERCIAL PRO WRC10224HC PREDATOR TALON WRC11524BSC PREDATOR WRC11524BS WRC11524CL PREDATOR COMMERCIAL PRO WRC10224H IMPORTANT Read and follow all Safety Precautions and Instructions before operating this equipment.
LIMITED WARRANTY The manufacturer’s warranty to the original consumer purchaser is: This product is free from defects in materials and workmanship for a period of (1) year from the date of purchase by the original consumer purchaser. We will repair or replace, at our discretion, parts found to be defective due to materials or workmanship.
Thank you for choosing Swisher’s 24” Walk Behind Rough Cut. Before operating your Walk Behind, please read, understand and follow all of the safety precautions and other instructions explained in this manual. As with all power equipment, lawn mowers can be potentially dangerous if not properly used. SAFETY PRECAUTIONS This Safety Alert Symbol indicates important messages in this manual. When you see this symbol, carefully read the message that follows and be alert to the possibility of personal injury.
Become familiar with the controls and their locations before operating. Use the figures below to find the general locations for controls and features discussed later in this manual Briggs & Stratton Models Honda Models 㳀ӝ PRE-OPERATING INSTRUCTIONS • • • • • Disengage spark plug wire and place where it cannot make a connection. Check the engine oil. All engines are filled with oil at the factory. Verify oil level and add if necessary before starting engine (See Engine Owner’s Manual).
BATTERY CONNECTIONS FOR ELECTRIC STARTER (applicable models) A battery is not shipped from the factory with the these units. Batteries are classified by their physical size, and individual size categories are given a "group number" by the Battery Council International. This Walk Behind Trail Cutter was designed to use a U1 battery group size or smaller.
OPERATING YOUR NEW WALK BEHIND The operation of any mower can produce foreign objects to be thrown into the eyes, resulting in severe eye damage. Always wear certified safety glasses or wide-vision safety goggles over spectacles before starting any cutting machine and while operating such a machine. The operation of any mower produces sound waves that are damaging to the human ear. Ear protection is recommended. CAUTION! Tragic accidents can occur if the operator is not alert to the presence of children.
STARTING THE ENGINE See engine manufacturer’s recommendations for the type and amount of oil and fuel used. Engine must be level to accurately check and fill oil. Do not overfill. • Make sure unit is level, blade is disengaged, and transaxle in “NEUTRAL” • Check spark plug wire, oil level, and fuel level. • Check all electrical connections for build-up of debris. • If equipped with a fuel shutoff valve, turn the valve to the ON position. • Move throttle control to “FAST”, or “CHOKE” if choke is needed.
BACKING UP • Release the Operator Presence lever on the right handle bar to disengage the blade. • Check behind you to make sure your path is clear. • Move the shift lever to the reverse position “R” and depress the “GROUND CONTROL” lever on the left handle bar. TRANSPORTING • Remove the key from ignition switch if equipped. • Shut off the fuel at the engine. • Secure in place with appropriate straps while the unit is being transported. • Unit should be left in low gear to avoid any slight rolling.
SAFETY AND OPERATIONAL DECALS Replace decal immediately if damaged. Order by part number from Swisher.
ASSEMBLY PARTS DETAIL WRC10224HC MODEL SHOWN WITH CASTERS SEE PAGE 11-12 FOR DETAILS SEE PAGE 13-14 FOR DETAILS ɱ䉆 SEE PAGE 14 FOR DETAILS ITEM # DESCRIPTION PART # 1 Guard - Engine, Cover 19888* 2 Guard - Engine, Right 20595* 3 Bolt - Serr Flange 5/16-18 X 3/4 NB596 4 Clip - Tinnerman 5/16-18 3706 5 Guard - Engine, Left 19885* 6 Guard - Engine, Front 19884* 7 Strap - Battery, 9" AS013 8 Hook - Battery Strap AS049 9 Battery (Not Included) N/A 10 Pad - Battery BATPAD 11
ENGINE & PULLEY ASSEMBLY for models equipped with HONDA ENGINE ITEM # 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 DESCRIPTION Nut - Nyloc 5/16-18 Bolt - Serr Flange, 5/16-18 X 1 Nut - Serr Flange 5/16-18 Bolt - 5/16-24 X 1 HCF GR5 ZY Bolt - Serr Flange, 5/16-18 X 1 1/2 Spacer - Engine Pulley Weldment - Belt Retention Belt - Transmission, 35" Washer - 1 X 1 1/2 Key Stock - 1/4 X 1 Engine Pulley- 4.25"OD,1 1/4 ID Washer - .
ENGINE & PULLEY ASSEMBLY for models equipped with BRIGGS & STRATTON ENGINE Install Transmission Cable (Not Shown) in Idler Arm before installing Idler Arm to Motor Plate. Important: Spring must be hooked in Idler Arm as shown. ɱ乆 ITEM # 1 DESCRIPTION Bolt - 5/16-18 X 1 1/4 Serr. Flange PART # NB253 2 Bolt - 5/16-18 X 3/4 Serr.
HANDLE BAR & LEVER ASSEMBLY for Honda and Briggs models. ITEM # 1 1 2 3 4 5 6 7 8 9 10 11 12 13 14 DESCRIPTION Weldment - Handle Bar, Honda Models Weldment - Handle Bar, Briggs Models Lever - Blade Engage Weldment Handle Grip Ground Control Lever Plate - Blade Lever Bolt - 5/16-18 X 3/4 Flange Head Bolt - 1/4-20 X 2.75, YZ Gr 8 Screw - 1/4-20 X 1/2 MSC ZP Truss Slot Bolt - 1/4-20 X 1.
HANDLE BAR & ENGINE CONTROLS for Honda models only. ITEM # 1 2 3 4 5 6 7 8 9 10 11 PART # 10216 21437 NB170 21444 9087 4226 KNOB 9088 NB114 3623 4226 21445 KSK 20988 ɱ婆 TRANSAXLE ASSEMBLY ITEM # 1 2 3 4 5 6 7 8 9 10 11 12 13 DESCRIPTION Wheel - Asy Right; WB24 4.
BLADE DRIVER ASSEMBLY ITEM # 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 DESCRIPTION Nut - Jam 3/4-16 Washer - Belleville .760 X 1.5 X .098 Pulley - Blade, 5.
DECK & CASTER ASSEMBLY (IF EQUIPPED) ITEM # 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 DESCRIPTION Deck - Weldment Bolt - 1/4-20 X 3/4 Clip - Blade Engagement Cable Nut - Nyloc 1/4-20 Nut - Serr Flange 5/16-18 Weldment - WB Skid Bolt - Serr Flange, 5/16-18 X 3/4 Washer - 5/8 ID X 1 OD Tire/Wheel - 8 X 3 Flat Free Nut - Lock Jam, 5/8-11 2 Way Bolt - 5/8-11 X 5 Weldment - Caster Washer - 13/16 X 1 1/4 X 1/8 Bearing Weldment - Brush Guard Housing Washer - Flat Nut - Jam, Nyloc 3/4-16 Cap PART # 10695* NB25
WIRING CONFIGURATION HONDA Engine Models Wiring Harness PN 20988 ȭꑆ︻ WIRING CONFIGURATION Briggs Engine Models Wiring Harness PN 19202 17
BELT ROUTING BELT PN: 20655 BLADE BELT BELT PN: 690 TRANSAXLE BELT ɱ畆 Specifications Engine Displacement Fuel Type Fuel Capacity Oil Type Oil Capacity Front Tire Size Rear Tire Size Rear Tire Pressure Overall Length Overall Height Unit Weight WRC10224HC Honda GXV390 389 CC *Unleaded 86 Octane 2.2 US Qts *SAE 10W-30 1.2 US Qts 8 X 3 Flat Free 16" Dia. X 4" Chevron 17 PSI Max 93.5" 38.7 "to 41.7" 291 Lbs Model WRC10224H Honda GXV390 389 CC *Unleaded 86 Octane 2.2 US Qts *SAE 10W-30 1.
swisherinc.com OWNER’S MANUAL MODEL NO. WRC10224HC RESIDENTIAL & COMMERCIAL PRO 24” WALK BEHIND ROUGH CUT TRAIL CUTTERS Each cutter has its own model number. Each engine has its own model number. The model number for the cutter will be found on the right hand side of the drive belt housing. The model number for the engine will be found on the engine block. All cutter parts listed herein may be ordered directly from Swisher or your nearest Swisher dealer.