Cascade Smart Seat Bidet INSTALLATION INSTRUCTIONS ® Swiss Madison @SwissMadison #WellMadeForever www.swissmadison.com | 1-434-623-4766 | info@swissmadison.
SMART SEAT BIDET INSTALLATION INSTRUCTIONS PRIOR TO INSTALLATION: · Inspect bidet to ensure no damages have occurred while in shipping. · Observe all plumbing and building codes in accordance with your state and local requirements. · All dimensions are nominal! Be sure to measure your toilet seat prior to installation. · The step-by-step guidelines in the installation instructions are a general reference. Should there be any discrepancies, Swiss Madison cannot be held liable.
SMART SEAT BIDET INSTALLATION INSTRUCTIONS When using electrical products, especially when children are present, basic safety precautions should always be followed: 1. The appliance is not to be used by people (including children) with reduced physical, sensory, mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction. 2. Children should be supervised and instructed not to play with the appliance. 3.
SMART SEAT BIDET INSTALLATION INSTRUCTIONS CAUTION - Failure to follow the instructions may cause body injury or property damage. 1. Do not install or use the product in wet places such as a steam room etc. 2. It is recommended to use a water-proof electrical outlet which should be installed in a place where it cannot easily get wet. 3. Do not stand on product unit, seat or cover. 4. Do not lean against the seat cover when using the product to avoid damage. 5.
SMART SEAT BIDET TECHNICAL SPECIFICATIONS SKU SM-STS21 Water Inlet Side Power Cord Inlet Side Net Weight 7.05 lb. Rated Voltage 120V~, 60Hz Rated Power Consumption 960W (When entering water temperature 15°C,flow rate 600ml/min) Maximum Power Consumption 1450W/120V Length of Power Cord 39.4” Water Supply Pressure 0.1 ~ 0.75MPa Water Supply Temperature 39 ~ 95°F Ambient Temperature 39 ~ 104°F Protection Class IPX4 Water Volume ≤0.7L/min(at a water pressure of 0.
SMART SEAT BIDET TECHNICAL SPECIFICATIONS 1. Remove Old Seat 2. Install Mounting Hardware · Remove old seat according to manufacturer’s instructions. Installation A: · Insert expansion bolts into ceramic holes. · Place the fixing bracket over the expansion bolts, followed by the adjustment sheets then screws. · Tighten screws with screwdriver. Installation B: · Place the fixing bracket over ceramic holes, followed by the adjustment sheets then screws. · Tighten nuts underneath screws. B A or 3.
SMART SEAT BIDET FUNCTIONS DEFAULT SETTINGS · When power is on the product will self test, when self test is over it will make a sound to notify the user it is ready to be used. · The water temperature default is about 95°F. · The seat temperature default is about 91°F. · The knob light and night light are always on.
SMART SEAT BIDET FUNCTIONS FUNCTION SETTINGS · The knob lamp can be turned off by pressing the water temperature and seat temperature buttons at the same time. Water temperature adjustment indicator Seat temperature adjustment indicator Prompt °F °F Light OFF Water temperature adjustment key Seat temperature adjustment key WATER TEMPERATURE SETTINGS °F to switch water temperature settings in the sequence below. · When switching to “OFF” , you will hear a long confirmation tone.
SMART SEAT BIDET MAINTENANCE SURFACE CLEANING · Turn off power supply before cleaning. · Wipe surface with a sponge or soft cloth dampened with room temperature water or natural detergent. · Do not replace toilet seat until ceramic toilet is completely washed, it may corrode the surface of the product. NOZZLE MAINTENANCE · Gently pull the wand out and in 5 times then wipe the wand clean with a soft, damp cloth dipped in neutral detergent, then wipe the nozzle and spray tube.
SMART SEAT BIDET PROBLEM TROUBLESHOOTING CAUSE SOLUTION Spray tube extends too slowly Cool water should be released from front end before flushing. It is normal, and provides normal flushing about 5s later. Insufficient water amount Knob is not completely turned on. Increase knob regulating angle. Insufficient water temperature Water temperature is set on low Adjust water temperature to higher gear. Water temperature is set on low Adjust water temperature to higher gear.
SMART SEAT BIDET PROBLEM TROUBLESHOOTING CAUSE SOLUTION Seat temperature is not sufficient Seat temperature is set at low gear. Adjust seat temperature to higher gear. Seat temperature is too high Seat temperature is set at high gear. Adjust seat temperature to lower gear. Temperature is too low when just contact with seat Not enable seat heating function. Enable seat heating function in advance. No seat heating function Seat heating coil in poor contact.
Swiss Madison ® ONE YEAR LIMITED WARRANTY 1-434-MADISON (623-4766) 19 Stults Road Dayton, NJ 08810 www.swissmadison.com Swiss Madison® products are made with quality materials and excellent craftsmanship to provide our customers with beautiful, durable, long-lasting products.
