Wall-Hung Carrier System INSTALLATION INSTRUCTIONS Swiss Madison Commercial Concealed In-Wall Toilet Tank Carrier System for Wall-Hung Toilet SM-WC426 @SwissMadison #WellMadeForever www.swissmadison.com | 1-434-623-4766 | info@swissmadison.
WALL-HUNG CARRIER SYSTEM INSTALLATION INSTRUCTIONS PRIOR TO INSTALLATION: · Inspect carrier to ensure no damages have occurred while in shipping. · Observe all plumbing and building codes in accordance with your state and local requirements. · All dimensions are nominal! Be sure to measure your toilet prior to installation. · The step-by-step guidelines in the installation instructions are a general reference. Should there be any discrepancies, Swiss Madison cannot be held liable.
WALL-HUNG CARRIER SYSTEM INSTALLATION INSTRUCTIONS 5 6 3 7 8 10 10 11 12 12 2 1 9 4 14 13 11 15 16 31 17 30 18 19 20 7 29 22 28 27 32 26 25 23 24 35 33 34 36 37 38 1. Attach Legs 21 39 · Attach legs to framing. · Adjust bowl height as desired. 16” 19 ¹¹⁄ min .
WALL-HUNG CARRIER SYSTEM INSTALLATION INSTRUCTIONS 2. Fasten Mounts · After adjusting bowl height, fasten four mounts (A). · Screw carrier to wood framing flush across the front. NOTE: It is recommended to use 2 1/2” screws and 1 1/4” fender washers (4 of each total). · Ensure frame is flush and level before fastening. A A A A A B B B 3. Connect Discharge Pipe · Find the center of the discharge pipe before fastening. Drill a 3 5/8” hole through framing for later installation.
WALL-HUNG CARRIER SYSTEM INSTALLATION INSTRUCTIONS 4. Fasten Mounts · Tie your mechanical coupling into your existing sanitary line using a 4x3” or 3x3” depending on your installation. · Thread in threaded bolts, be sure the slotted end is to the outside for later adjustments. Place plastic sleeves over the end of the bolts to protect during installation. · Place dust covers as shown below. 5. Cut Drywall · Install dry wall over carrier system in intended location. · Find included cutout template.
WALL-HUNG CARRIER SYSTEM INSTALLATION INSTRUCTIONS 6. Remove Actuator Cover 1 1 2 7. Tighten Water Connection · Hold shutoff valve stationary while tightening your water connection. · Install the locking nut as shown below.
WALL-HUNG CARRIER SYSTEM INSTALLATION INSTRUCTIONS 8. Flush Debris · Once the water connection is made to the water shutoff valve, undo the other side of the hose. · Turn on the valve to flush out any debris before re-installing to the actuator. 00:00:45 9. Reconnect Waterline and Actuator · Once flushed, reconnect the waterline and actuator.
WALL-HUNG CARRIER SYSTEM INSTALLATION INSTRUCTIONS 10. Secure Roughing Box · Ensure roughing box is secure to keep any debris from entering the tank. “Click” 11. Install Wall Materials · Trim roughing box after installing wall materials. max. ¹⁄8” max.
WALL-HUNG CARRIER SYSTEM INSTALLATION INSTRUCTIONS Toilet Installation 1. Fit Pipes · Install pipes and make sure they are thoroughly inserted. · With a ruler, mark a line on the pipe where it meets the finished wall. · Remove from wall and install pipes in the back of the toilet and make sure they are thoroughly inserted. · With a ruler, mark a line on the pipe where it meets the back of the bowl. 2. Cut Pipes · Measure the distance between both marked lines on pipe. · Cut pipes as shown below.
WALL-HUNG CARRIER SYSTEM INSTALLATION INSTRUCTIONS 3. Mount Bowl · With grease sponge, thoroughly lubricate all ends. · Before mounting, measure thickness of china and mounting hardware to get approximate depth of threaded rods. · Use slotted end of thread bolt to adjust in or out. Do not damage the thread. 1” d · Install with mounting hardware and ensure toilet bowl is level.
Swiss Madison ® ONE YEAR LIMITED WARRANTY 1-434-MADISON (623-4766) 19 Stults Road Dayton, NJ 08810 www.swissmadison.com Swiss Madison® products are made with quality materials and excellent craftsmanship to provide our customers with beautiful, durable, long-lasting products.