Wall-Hung Carrier System INSTALLATION INSTRUCTIONS ® well made forever Commercial Concealed In-Wall Toilet Tank Carrier System for Wall-Hung Toilet SM-WC426 @SwissMadison #WellMadeForever www.swissmadison.com | 1-434-623-4766 | info@swissmadison.
WALL-HUNG CARRIER SYSTEM INSTALLATION INSTRUCTIONS PRIOR TO INSTALLATION: · Inspect carrier to ensure no damages have occurred while in shipping. · Observe all plumbing and building codes in accordance with your state and local requirements. · All dimensions are nominal! Be sure to measure your toilet prior to installation. · The step-by-step guidelines in the installation instructions are a general reference. Should there be any discrepancies, Swiss Madison cannot be held liable.
WALL-HUNG CARRIER SYSTEM 5 INSTALLATION INSTRUCTIONS 6 3 8 7 10 9 10 11 4 12 13 15 14 16 18 17 30 19 20 12 11 31 7 29 28 27 32 22 23 25 40 33 37 21 41 24 40 42 38 Flush Actuator not included 39 1. Attach Legs · Attach legs to framing. · Adjust bowl height as desired. ” 19 min .
WALL-HUNG CARRIER SYSTEM INSTALLATION INSTRUCTIONS 2. Fasten Mounts · After adjusting bowl height, fasten four mounts (A). · Screw carrier to wood framing flush across the front. NOTE: It is recommended to use 2 1/2” screws and 1 1/4” fender washers (4 of each total). · Ensure frame is flush and level before fastening. A A A A A B B B 3. Connect Discharge Pipe · Find the center of the discharge pipe before fastening. Drill a 3 5/8” hole through framing for later installation.
WALL-HUNG CARRIER SYSTEM INSTALLATION INSTRUCTIONS 4. Fasten Mounts · Tie your mechanical coupling into your existing sanitary line using a 4x3” or 3x3” depending on your installation. · Thread in threaded bolts, be sure the slotted end is to the outside for later adjustments. Place plastic sleeves over the end of the bolts to protect during installation. · Place dust covers as shown below. 5. Cut Drywall · Install dry wall over carrier system in intended location. · Find included cutout template.
WALL-HUNG CARRIER SYSTEM INSTALLATION INSTRUCTIONS 6. Remove Actuator Cover 1 1 2 7. Tighten Water Connection · Hold shutoff valve stationary while tightening your water connection. · Install the locking nut as shown below.
WALL-HUNG CARRIER SYSTEM INSTALLATION INSTRUCTIONS 8. Undo Waterline Hose · Once the water connection is made to the water shutoff valve, undo the other side of the hose. 1 2 9. Flush Debris & Reconnect Waterline and Actuator · Turn on the valve to flush out any debris before re-installing to the actuator. · Once flushed, reconnect the waterline and actuator.
WALL-HUNG CARRIER SYSTEM INSTALLATION INSTRUCTIONS 10. Secure Roughing Box · Ensure roughing box is secure to keep any debris from entering the tank. “Click” 11. Install Wall Materials · Trim roughing box after installing wall materials. max. zƔȤ” max.
WALL-HUNG CARRIER SYSTEM INSTALLATION INSTRUCTIONS Toilet Installation 1. Fit Pipes · Install pipes and make sure they are thoroughly inserted. · With a ruler, mark a line on the pipe where it meets the finished wall. · Remove from wall and install pipes in the back of the toilet and make sure they are thoroughly inserted. · With a ruler, mark a line on the pipe where it meets the back of the bowl. 2. Cut Pipes · Measure the distance between both marked lines on pipe.
WALL-HUNG CARRIER SYSTEM INSTALLATION INSTRUCTIONS 3. Mount Bowl · With grease sponge, thoroughly lubricate all ends. · Before mounting, measure thickness of china and mounting hardware to get approximate depth of threaded rods. · Use slotted end of thread bolt to adjust in or out. Do not damage the thread. 1” d · Install with mounting hardware and ensure toilet bowl is level.
® well made forever ONE YEAR LIMITED WARRANTY 1-434-MADISON (623-4766) www.swissmadison.com Swiss Madison® products are made with quality materials and excellent craftsmanship to provide our customers with beautiful, durable, long-lasting products.
