Back-to-Wall Carrier System ® INSTALLATION INSTRUCTIONS well made forever Residential Concealed In-Wall Toilet Tank for Back-to-Wall Toilet SM-WC324 @SwissMadison #WellMadeForever www.swissmadison.com | 1-434-623-4766 | info@swissmadison.
BACK-TO-WALL CARRIER SYSTEM INSTALLATION INSTRUCTIONS PRIOR TO INSTALLATION: · Inspect carrier to ensure no damages have occurred while in shipping. · Observe all plumbing and building codes in accordance with your state and local requirements. · All dimensions are nominal! Be sure to measure your toilet prior to installation. · The step-by-step guidelines in the installation instructions are a general reference. Should there be any discrepancies, Swiss Madison cannot be held liable.
BACK-TO-WALL CARRIER SYSTEM INSTALLATION INSTRUCTIONS Parts for Reference: 1 2 3 4 5 7 8 9 10 11 6 12 13 14 15 16 17 18 19 20 23 21 24 22 25 26 27 32 28 29 Flush Actuator not included 31 30 — 2 —
BACK-TO-WALL CARRIER SYSTEM INSTALLATION INSTRUCTIONS 1. Fasten Mounts (if fastening to studs) · Adjust clips then fasten carrier to studs or wall framing. · Ensure frame is flush and level before fastening. 1a. 1b.
BACK-TO-WALL CARRIER SYSTEM INSTALLATION INSTRUCTIONS 1. Fasten Mounts (if fastening to wall) · Adjust clips then fasten carrier to studs or wall framing. · Ensure frame is flush and level before fastening.
BACK-TO-WALL CARRIER SYSTEM INSTALLATION INSTRUCTIONS 2. Cut Pipe · Measure and cut pipe according to your toilet. · Make sure to measure the sub floor and finished floor measurements before cutting to have the correct center. · Once pipe is cut, remove any burrs. 39 tƔȤ” 1 2 L(max. 5 zɀƔdžȢ”) L=X-H 3 H X 0 3. Attach Pipe · Apply grease before sliding on pipe. · Install pipe then put on dust cap to prevent debris from entering the pipe.
BACK-TO-WALL CARRIER SYSTEM INSTALLATION INSTRUCTIONS 4. Remove Plate · Remove plate and attach to water connection. 1 1 1 2 2 2 3 1 5. Attach Water Connection · Hold the shut-off valve stationary while tightening water connection. · Install locking nut as shown.
BACK-TO-WALL CARRIER SYSTEM INSTALLATION INSTRUCTIONS 6. Flush Debris · After attaching water connection to shut-off valve, undo the other side of the hose. · Turn on valve to flush any debris before installing the actuator. 1 2 3 7. Reconnect Water Supply · After flushing debris, reconnect the water supply hose. a. c. 2 1 b. d.
BACK-TO-WALL CARRIER SYSTEM INSTALLATION INSTRUCTIONS 8. Reinstall Plate · Reinstall actuator and cover plate. · Ensure roughing box is secure to keep debris from entering the tank. *Click* 2 2 1 1 *Click* 9. Trim Roughing Box · After wall materials are installed, trim roughing box.
BACK-TO-WALL TOILET INSTALLATION INSTRUCTIONS Toilet Installation 1. Fit Pipe · Install pipe and make sure it is thoroughly inserted. · With a ruler, mark a line on the pipe where it meets the finished wall. · Remove from wall and install pipe in the back of the toilet and make sure it is thoroughly inserted. · With a ruler, mark a line on the pipe where it meets the back of the bowl. 2. Cut Pipe · Measure the distance between both marked lines on pipe.
Back-to-Wall Toilet INSTALLATION INSTRUCTIONS @SwissMadison #WellMadeForever www.swissmadison.com | 1-434-623-4766 | info@swissmadison.
BACK-TO-WALL TOILET INSTALLATION INSTRUCTIONS PRIOR TO INSTALLATION: · Inspect toilet to ensure no damages have occurred while in shipping. · Observe all plumbing and building codes in accordance with your state and local requirements. · All dimensions are nominal! Be sure to measure your toilet prior to installation. · The step-by-step guidelines in the installation instructions are a general reference. Should there be any discrepancies, Swiss Madison cannot be held liable.
BACK-TO-WALL TOILET INSTALLATION INSTRUCTIONS 1. Install Tank Carrier System 2. Dry Fit Outlet Pipe and Inlet Pipe 3. Cut Pipes 4. Connect Pipes · Before toilet bowl installation, a wood frame and commercial or residential tank system is required. · Install according to manufacturer's instructions. · Measure the distance between both marked lines on pipe. Take measured distance, deduct from bald end of pipe and cut pipes as shown below. · After cutting, take a file and remove all burrs.
BACK-TO-WALL TOILET INSTALLATION INSTRUCTIONS 5. Fit and Level Bowl · Place the bowl facing the flush pipe and waste pipe, then push firmly until it touches the wall to ensure that both pipes are in the correct position and the correct length. · Make sure bowl is level then mark on both sides of the bowl where the anchors will be installed. 6. Install Anchors and Brackets · Remove the toilet bowl and measure the thickness of the bowl.
BACK-TO-WALL TOILET INSTALLATION INSTRUCTIONS TOILET SEAT INSTALLATION 1. Dissassemble · Disassemble the cover cap and the hinge. 2. Construct Hinges · Insert screw and nut into the hole on the hinge. · Attach blind hole screw fixing to the bottom of screw. Pull or 3. Attach Hinges · Insert hinges with blind hole screw fixings attached into holes on toilet bowl. · Lightly tighten hinges with a screwdriver to allow for later adjustment. 4.
BACK-TO-WALL TOILET INSTALLATION INSTRUCTIONS 5. Adjust and Attach Seat · Align seat to the hinges then firmly tighten the hinges. · Attach seat to the secure hinges. · Adjust seat to align to the bowl. TOILET SEAT USAGE · To remove, push middle button until you hear a “click”, then pull straight up. · To re-install, align hinge posts with reference marks on seat, then push down until your hear a “click”.
Wall-Mount Actuator Flush Plate INSTALLATION INSTRUCTIONS @SwissMadison #WellMadeForever www.swissmadison.com | 1-434-623-4766 | info@swissmadison.
ACTUATOR FLUSH PLATE INSTALLATION INSTRUCTIONS PRIOR TO INSTALLATION: · Inspect product to ensure no damages have occurred while in shipping. · Observe all plumbing and building codes in accordance with your state and local requirements. · The step-by-step guidelines in the installation instructions are a general reference. Should there be any discrepancies, Swiss Madison cannot be held liable. It is recommended to install all Swiss Madison products by hiring a licensed professional.
ACTUATOR FLUSH PLATE INSTALLATION INSTRUCTIONS 1. 2. 3. 4. turn on 5. 6.
ACTUATOR FLUSH PLATE INSTALLATION INSTRUCTIONS 8. 7. *Click* 9. 10. 0 “Click’’ 11. 2 12.
® well made forever ONE YEAR LIMITED WARRANTY 1-434-MADISON (623-4766) www.swissmadison.com Swiss Madison® products are made with quality materials and excellent craftsmanship to provide our customers with beautiful, durable, long-lasting products.
