User manual
Tip: Some features require extra
memory, to expand your phone’s storage
capacity, install a micro SD card.
3. Micro-SD card (optional)
Lightly press the card holder and
push it carefully toward the side of the
compartment. The card holder can
now be ipped up vertically. Place
the memory card in the black plastic
bracket. Make sure that the memory
card contacts are facing down and that
the card is placed in accordance with
the marked area (see gure). Do not
scratch or bend the card contacts. Push
the metal holder back down, press it at
and slide it until it snaps into place.
1. Voume up
Volume down
2. Headset
socket
For 3.5 mm standard
headset
3. Micro USB
port
For battery charger
4. Torch
shortcut
5. Receiver/
loudspeaker
Make phone calls
holding the cell phone
to the ear
6. Display
7. Left soft key
Menu
8. Call key
Dial and answer calls;
open the call log
9. M1
memory key
10. Voicemail
11. Camera
shortcut
12.
*
key
In idle state: to enter:
“*”/ “+” / “P”/“W“;
Input: special charac-
ters
13. Arrow key up
In idle state to open
new SMS
14. Right soft
key
Phone book
15. End key
16. Arrow key
down
To open alarm func-
tion.Scroll up and
down in menus and
lists
17. M2
Memory key
18.
#
key
In idle state: long
keystroke to toggle
between ring tone on,
mute and vibration;
Input: toggle input
modes
19. Space bar
Enter space while writ-
ing SMS
20. Torch
Camera ash
21. Led
22. External
display
23. SOS key
24. Loudspeaker
Install the SIM card and the battery
The SIM card holder is located inside the
battery compartment.
CAUTION
Only use batteries, charger and
accessories that have been approved for
use with this particular model. Connecting
other accessories may be dangerous and
may invalidate the phone’s type approval
and guarantee.
1. Remove the battery cover
slide your ngernail into the small
notch on the left bottom side of the
phone and pull the cover upward. If the
battery is installed, slide your ngernail
in the notch at the bottom to lift up the
battery.
2. Insert the SIM card (required)
push it carefully in under the metal
bracket. Make sure the contacts of
the SIM card point downwards and
the cut-off corner ts exactly in the
recessed shaping of the holder. The
contacts of the SIM card must not be
scratched or bent. Try not to touch the
contacts with your ngers.
BBM 625
© IVS GmbH 2015 • All rights reserved
QSG_Swisstone BBM_625_en_A3(A7)_v1.0
English
Version 1.0
1313
Specications
Network:
GSM 900/1800 MHz
Dimensions:
99 mm x 51 mm x 19 mm
Weight:
89 g
Battery:
3.7V/800 mAh Li-ion
battery
Operating ambient
temperature:
Min: 0°C (32°F)
Max: 40°C (104°F)
Charging ambient
temperature:
Min: 0°C (32°F)
Max: 40°C (104°F)
Storage
temperature:
Min: -20°C (-4°F)
Max: 60°C (140°F)
Changes and errors excepted.
EN
IMPORTANT!
Use only compatible memory cards
with this device. Compatible card type:
microSD, microSDHC.
Incompatible cards may damage the
card itself, the device and corrupt any
data stored on the card. Depending on
the market some phones may have a
pre-installed memory card.
4. Insert the battery (required)
by pushing it into the battery
compartment ensuring that the three
contacts on the front touch the three
spring contacts on the top in the
battery compartment.
5. Replace the cover and push it upward
using gentle pressure with the thumb
until it snaps securely into place again.
When the battery performance is low, the
empty battery symbol ashes to indicate
the battery state and an alarm signal will
sound. To recharge the battery, connect the
mains adapter to the micro USB connector
on the right side of the phone.
Alternatively, you can place the telephone
into the charging cradle connected to the
main adapter via the USB cable.
During charging, the charge status icon
moves (visible in the upper right corner of
the display).
A complete charging process of the
rechargeable battery takes approximately 3
hours. When the battery is fully charged the
animation of the charge status icon stops.
Power on the phone
Press and hold the red key on the
phone to turn it on and off.
If the SIM card is valid but protected with a
PIN code (Personal Identication Number),
Input PIN
is displayed.
Enter the SIM PIN code and press
OK
( upper left corner of keypad). Delete
with
Clear
( upper right corner of
keypad).
Make a call
1. Enter the phone number with the area
code. You can delete digits with
Delete
.
2. Press to dial. Press
Hang up
to
cancel dialling.
3. Press to end the call.
Tip: For international calls, always enter
a + symbol before the country code to be
able to use the phonebook optimally in
any country.
Press the
*
key twice to enter the inter-
national area code +.
Answer a call
1. Press or
Answer
to accept the call
or press reject to reject the call (busy
signal).
Alternatively, you can press to
reject the call directly.
2. Press to end the call.
Create phonebook entry
1. Press
Menu
â
Contacts
â
OK
.
2. Select
Options
â
New
.
3. Select whether you want to save the
contact on the SIM card or in the phone.
4. Enter a name for the contact.
5. Press .
6. Enter the phone number including the
area code.
7. Press .
8. Then press
Save
â
OK
.
Tip: For international calls, always enter
a + symbol before the country code to be
able to use the phonebook optimally in
any country.
Set language
The default language of the phone menu,
messages and so on is determined by the
SIM card used (Automatic). You can always
switch between the languages supported
by the phone.
1. Press
Menu
â
Settings
â
OK
.
2. Select
Phone settings
â
OK
.
3. Select
Language settings
â
OK
.
4. Select
Display language
â
OK
.
Set time and date
1. Press
Menu
â
Settings
â
OK
.
2. Select
Phone settings
â
OK
.
3. Select
Date & time
â
OK
.
4. Select
Set time/date
â
OK
.
5. Enter the time (HH:MM) â .
6. Enter the date (DD/MM/YYYY) â
OK
.
Press the
*
key twice to enter the inter-
national area code +.
Volume control
You can adjust the volume during a call
using the side keys
+
/
–
. The volume level is
shown on the display.
Enter text
Select character
• Press a numerical key repeatedly
until the desired character is shown.
• Wait a few seconds before entering
the next character.
Special characters/smileys
• Press
*
to view a list of special
characters.
• Select the desired character with or
or (to move left or right) and
press
OK
to enter.
Move the cursor within text
• Use the keys or , to move the
cursor within the text.
Upper case, lower case and numerals
• Press
#
to choose between upper
case, lower case and numerals. The
symbol at the top left in the display
indicates the input mode.
Instructions