Swiwin Turbine Brushless Series Kero Start Full Autostart with Auto-Restart Operations Manual
Introduction This manual is intended to aid the user in setup and running practices associated with the SWIWIN SW series micro turbines. This manual is not intended to take the place of a primer on micro-turbines. It is assumed that the user has working knowledge and experience with turbines and that each user is familiar with best practices before attempting to run a turbine. Non- Disclaimer Turbines are inherently dangerous to run.
User acknowledges the risk of injury or burns to bystanders during start-up or while operating a turbine. User agrees to take all steps necessary to ensure that all persons are situated a safe distance from the operations of the engine. Please refer to figure 1. Always ensure, that all bystanders maintain a safe distance from the engine. clear of the area to the rarely catastrophically malfunction but in the rare event of an issue, it is best to maintain a safe distance.
time free sevice. 3. First year warranty covers all parts except for batteries. 4. Warranty not coverage applies after one year or 25 hours of running time , the following items: a. Combustion chamber b. Shaft c. Shaft tunnel d. Diffuser e. Injectors f. NGV g. Turbine wheel 5. Warranty does not cover the following items: a. Damage to Can b. Crash Damage c. Starter motor d. Glow Plug e. Any FOD damage including and not limited to: i. Broken compressor blades ii. Scored intake cover f. Diffuser g.
j. Turbine serial number has been removed or altered. k. Turbine is found to have been operated with 2 cycle oil 7. If a problem occurs during the warranty period, please contact our service department and take the following steps: a. Contact sw-jet@qq.com in order to coordinate shipping of the turbine to the service center for evaluation and repair. b. Send the turbine to our repair center. Please include all user information including address and daytime phone number, email address, etc.
1.Connect one end of the servo cable (provided) between the ECU port labeled “ppm” and the other end to your receiver, if use telemetry function, use telemetry port. 2. Connect the Battery cable to ECU port labeled “3S LIPO BATT” 3. Connect the pump to the deans connector on the battery cable V3 ECU 4. Connect the GSU to the ECU port labeled “GSU/PC”. 5. Connect the engine cable to the ECU port labeled “ENGINE”.
Motor Setup Please refer to Figure 3 - Motor Setup above 1. Connect the motor festo fitting to a section of 4mm tubing (included). 2. Route the tubing to the filter then to the shut off as shown. 3. Connect the other end of the shutoff with 4mm tubing to the output of the supertrap pump. 4. Plumb the UAT as shown and per the UAT instructions (UAT is not included) 5. Plumb the Fuel tank per the manufacturer instructions noting orientation above. 6. Connect Input of fuel pump to UAT fuel out fitting 7.
Pump tube connection Startup Operation Prior to running the turbine walk around the aircraft or motor stand and make sure that all power and data connections are placed properly. 1. Turn the fuel valve to the on position 2. Turn on power to the receiver and observe GSU startup. The motor and GSU will sync up with an audible signal. 3. If this is the first startup, use the test menu and locate “test pump” function. 4. Prime the lines with fuel using the test pump function.
Shutdown Procedure Always observe proper shutdown and cooling of the turbine. Failure to observe proper shutdown by not properly cooling the unit will render damage and will void the warranty. To shut down the turbine 1. Lower the stick to minimum 2. Lower trim to minimum 3. The motor will shut down and initiate a cooldown sequence by turning on the starter motor to an RPM defined in motor parameters. This cool down speed is determined in cooling menu of ECU setup. The default cool down speed is 7000 rpm.
Data Logging Auto start Automatic Restart Color Screen visible in direct sunlight Configurable thrust curve with very fast throttle response Telemetry function BUS input ECU/Motor Electrical Connections Do not exceed these voltages! Receiver voltage：5-8.4V(4S Nimh or 2S Life or 2S Lipo) Power voltage：11.
Large font Running Screen Press “C” to toggle between large screen and normal Main menu – initial screen From the initial screen, press “OK” key, click “C” to toggle back to boot screen StartUp – enter startup menu Running – enter Running menu Adjust RC – Train Radio to ECU Starter – set starter power Cooling – set cooling rpm Other – enter other parameters menu Test – enter Test menu DataChart – running data records Language - switchable Chinese or English Start Up Screen PumpVoltage - Set pump voltage Ty
Running Display RPM Acceleration/Deceleeation Curve/Delay time Higher values mean a faster rpm increase/decrease rate. Adjust according to weather, Altitude (ASL) or other conditions which require adjustments to delay time. It is best to select a value that is lower than a setting that yields the fastest possible response time in order to avoid a flame out.
Starter Eject Time – sets the time for a reverse voltage pulse to disengage the starter. Eject Voltage – sets the eject voltage in order disengage the clutch on startup Run Voltage – Sets the voltage for the starter during startup RPM Stable – rpm adjust rate of starter Engine Cooling Sets the cooling rpm after shut down or when starter is manually run using test functions. *Please note that following a failsafe failure or flameout that the motor will not automatically enter a cool down sequence.
Test function menu Press “OK” to access test functions Test Pump – depress OK and hold OK to increase pump speed. Pump increases gradually. Test pump initiates fuel solenoids simultaneously. Be careful not to flood the engine. Test Fuel Valve – press “OK” to activate fuel valve. Test Gas Valve – press “OK” to activate Gas Valve – this controls fuel to the glow plug. Test Glow Plug – press “OK” to activate Glow Plug circuit. A glow can be seen from the rear of the motor.
SWIWIN TURBINE SPEC SW60B SW80B SW120B SW140B SW170B SW190B SW220B SW300B SW400B Diameter 84mm 83mm 99mm 99mm 109mm 109mm 116mm 133mm 146mm Length 203mm 203mm 250mm 250mm 258mm 258mm 275mm 342mm 335mm Weight 780g 780g 1250g 1250g 1450g 1450g 1700g 2500g 3000g 50,000- 50,000- 38,000- 38,000- 36,000- 36,000- 38,000- 38,000- 33,000- 150,000 155,000 125,000 130,000 113,000 116,000 115,000 98,000 95,000 60N 80N 120N 140N 170N 190N 220N 300N 400N 7
引擎启动 Startup SW60B SW80B SW120B SW140B SW170B SW190B SW220B SW300B Pump voltage 0.7-0.9 0.7-0.9 0.7-0.9 0.7-0.9 0.7-0.9 0.7-0.9 0.7-0.9 0.7-0.9 RpmStartup ramp 100% 100% 100% 100% 100% 100% 100% 100% 3 3 3 3 3 3 3 3 Glow plug 6.2 6.2 6.2 6.2 6.2 6.2 6.2 6.
