SY-KVM31036 1 USB 3.0 KVM Switch Model: SY-KVM31036 User Manual Ver. 2.
SY-KVM31036 2 Product Introduction The USB 3.0 KVM Switch is a high quality and durable system which allows control over multiple computers/servers from one console. (mouse, keyboard, monitor, microphone, and speaker) Features - Controls 3 computers from a single console (keyboard/mouse) over a USB connection using standard USB cables. - Supports 1 MHL (Mobile High-Definition Link) smart phone projected display via the specific Micro USB to HDMI with power charged synchronization.
SY-KVM31036 3 - Provides audio switching in independent method or combination with the host switching (enable/disable by hotkey). - Auto-scan function (time interval can be adjusted between 5-20 seconds when the auto-scan function is enabled. - Plug and Play Package Contents - 1 x 4-port USB 3.0 HDMI KVM with USB 3.0 Hub and Audio and MHL - 2 x HDMI Cable - 2 x USB 3.0 Cable - 2 x 3.
SY-KVM31036 4 - One monitor which supports HDMI - One keyboard/mouse Note: Wireless keyboard/mouse may not work properly with tis KVM switch. - One speaker and microphone with relative cable if necessary - One USB device to USB downstream port is necessary.
SY-KVM31036 5 Hardware Installation 1. Connect USB keyboard/mouse to the console front ports of the KVM. 2. Connect all audio cables to each computer, KVM, speaker, and microphone is necessary. 3. Connect any other USB device to the USB 3.0 Hub downstream ports if necessary. 4. Connect the monitor HDMI cable to the monitor output port of the KVM. 5. Connect the DC 5V power adaptor to the KVM. 6. Connect the HDMI cable between the HDMI port on the computer display card and the HDMI input port on the KVM.
SY-KVM31036 6 Notice for Sun Micro System user Some Sun Micro Systems do not support the USB 3.0 HUB feature during the booting period. If you are using such Sun Micro Systems it is possible that you will see a system prompt message that the keyboard failed to be detected. At this point the screen will go blank for a few minutes then the login screen will display.
SY-KVM31036 7 LED Indicators Host Selected Indicators (RED) - On: Indicates which PC is available and selected. - Flash: Indicates which Host PC is selected but is not available. Hub Selected Indicators (Green) - Indicates which PC is connected with the UDB Hub downstream ports. Hub auto-switch / Auto-scan Indicator (Green) - On: Hub Auto-Switch mode is active. The UDB HUB will be switching with the selected PC - Off: Hub Auto-Scan mode is inactive.
SY-KVM31036 8 Operations Push Button Operation You can switch to any desired USB host connection with audio together by pushing the button on the front panel of the KVM switch. You can also disable the Audio Auto-Switch function hotkey. Host Selection (Hotkey Support) The hotket function is working on the USB keyboard which is plugged in at the port marked with the keyboard logo of the KVM.
SY-KVM31036 9 Host Selection (Host Selected Indicator) The host selected LED (Red) on the KVM front panel indicates the host port status: - On: Indicates the host port is available and selected. - Off: Indicates the host port is not selected. - Flash: Indicates the host port is selected but is not available. Hub Selection Hub Selection (USB Hub Switch by Push Button) You must enable the Hub Auto-switch function before you can use the push button switch.
SY-KVM31036 10 Hub Selection (Hot key Switch for USB Hub Selection) If the Hub Auto-Switch function is disabled, the USB hub switch is independent from the host port.
SY-KVM31036 11 Audio Selection Audio Selection (Audio Auto-Switch Function) Press [Scroll Lock] + [Scroll Lock] + [A], then the Audio-Switch function will be disabled/enabled alternately. The Audio-Switch function is on by default. Audio Selection (Hotkey Switch for Audio Selection) You can use the following hotkeys to switch audio to the indicated port. There is no indicator for the audio selection.
SY-KVM31036 12 Auto-Scan Function (Stop Auto-Scan) Press the Space key: Will stop the auto-scan and will stay in the current scanning port. Press any other key on the keyboard: Pressing any keys, excluding the number key [1], [2], [3], and [4], will turn off the auto-scan function. The monitor screen will then jump back to the original host port before the auto-scan.
SY-KVM31036 13 Sun Micro Systems Function Key Emulation There are 16 special functions on the Sun Micro Systems keyboard which the KVM can emulate. Below is the mapping table for the function key emulation. To activate these emulation keys, you have to press the Left Window Key first then, choose the second relative key.
SY-KVM31036 14 List of Hot Keys
SY-KVM31036 15 FAQ Question: I installed the device and connected my systems but there is no display to my monitor? Answer: Please remember to connect the power cable to the kvm switch and, ensure all cables are connected to the proper in/out ports. Question: The device is not working with my system. Are there drivers I can download to fix this? Answer: No, there are no drivers/firmware for this device.
SY-KVM31036 16 Version Information Version: 2.0 Date Updated: 3/20/2014 Changes/Fixes: - Compiled manual information into .pdf format. - Cleaned up wording and text throughout the previous 1.0 manual. - Added hotkey functionality sheet - Added FAQ of general information.
