Operating Instructions Transponder code lock - Part 2 (split decoder) Item no. 1582599 / for surface mounting Item no.
TABLE OF CONTENTS Page 1. INTRODUCTION..................................................................................................................................................4 2. EXPLANATION OF SYMBOLS............................................................................................................................4 3. INTENDED USE...................................................................................................................................................5 4.
24. PACIFIER TONES ON-OFF SELECTION -- Location 71...................................................................................40 25. OUTPUT OPERATION ANNOUNCER -- Location 72........................................................................................41 26. STATUS LED FLASHING ON-OFF DURING STANDBY -- Location 73............................................................41 27. DOOR FORCED OPEN WARNING & TIMING -- Location 80.................................................................
1. INTRODUCTION Dear customer, Thank you for purchasing this product. This product complies with the statutory national and European requirements. To maintain this status and to ensure safe operation, you as the user must observe these operating instructions! These operating instructions are part of this product. They contain important notes on commissioning and handling. Also consider this if you pass on the product to any third party.
3. INTENDED USE DA-2800 and DA-2801 are full feature self-contained split-decoders. They are specially designed to work with the keypads in DK-2800 MK-II series and up-grade them for split-decoded operation. Any keypad of DK-2800 MK-II can be up-graded to full feature operation once it is linked up with the split-decoder even it is originally a low cost, most basic keypad. The DK-2800 MK-II keypad changes its role as a server in split-decoded operation.
5. FEATURES AND FUNCTIONS • Fully Compatible with All The Keypads of DK-2800 MK-II Series for Split-decoded Operation • Full Feature Signal Decoding for Tri-Tech Operation • Simple Three Wire Connection for Split-decoded Data Communication; (+), (-) & Data I/O • Compatible with All The Keypads of 12V/DC and 12-24V/DC Operations • Three Form C Relays with N.C. and N.O. Dry Contacts • All Relay Outputs Are Configurable with Auto Reset Timer Mode or Start / Stop Mode.
6. SAFETY INSTRUCTIONS For safety instructions please refer to Part 1 of these operating instructions. 7. INSTALLATION PRECAUTIONS Please study the manual to become familiar with all the specifications and features of the system before installation. IMPORTANT NOTE TO INSTALLER • The operation voltage of the DK-2800 MK-II series keypads consist of 12V/DC and 12-24V/DC versions while the Split-Decoders DA-2800 and DA-2801 are 12-24V/DC.
Power Supply for The System A good power supply is very important to the stability of the keypad system. Make sure it can provide sufficient power for the whole system especially the appliance taking heavy power to operate. Make sure no large voltage fluctuation when the appliance starts and stops operation if the keypad is supplied from the same power source. Electric Spikes And Voltage Fluctuation It is important to prevent the electric spikes feed-in to the keypad.
THE MAIN CIRCUIT BOARD LINK UP CODE LEARNING BUZZER RECEIVER FOR REMOTE CONTROL The Facilities - DA-2800 Connection Terminals: See details in “Connection Terminal” section. Internal Siren & Door Chime: It gives warble tone alarm siren and dual tone door chime Link-up Jumper: A tool for setting up the link with the server keypad, see details in “Jumper Settings and Link-up Procedures” section on page 17.
Buzzer: A buzzer gives audible tones showing the system status: STATUS TONES Power-up Delay (Split-decoded mode) Continuous beeps for 5 seconds Successful Command from RF Keyfob 2 short beeps Output Relay Active 2 beeps short beeps Egress Delay Warning Fast beeps Door Propped-up Warning Fast beeps Door Forced Open Warning Fast beeps and alarm Code Learning Button: A tool for recording the code of the RF keys and wireless keypads (optional).
THE MAIN CIRCUIT BOARD LINK UP BEEP BUZZER The Facilities - DA-2801 Connection Terminals: See details in “Connection Terminal” section. Internal Siren & Door Chime: It gives warble tone alarm siren and dual tone door chime Link-up Jumper: A tool for setting up the link with the server keypad, see details in “Jumper Settings and Link-up Procedures” section on page 17.
Buzzer: A buzzer gives audible tones showing the system status: STATUS TONES Power-up Delay (Split-decoded mode) Continuous beeps for 5 seconds Successful Command from RF Keyfob 2 short beeps Output Relay Active 2 beeps short beeps Egress Delay Warning Fast beeps Door Propped-up Warning Fast beeps Door Forced Open Warning Fast beeps and alarm 9. CONNECTION TERMINALS DA-2800 & DA-2801 LINK UP -ALARM O/P -KEY ACT O/P -N.O. -COM -N.C. -N.O. -COM -N.C. -N.O. -COM -N.C.
1 - 2: 12-24V/DC I/P -- (Power Input Terminal) Connect to a 12-24V/DC power supply. The (-) supply and the (-) GND are the common grounding points of the system. The system accepts full input voltage range. 3: KEYPAD POWER O/P -- (Power Output for External Keypads – 500mA Max.) This power source is prepared for the external keypad(s). Its output voltage follows to the input voltage at terminals 1 - 2 but the output current is limited to 500mA only.
9: O/P 1 INHIBIT -- (Output 1 Inhibit Control Input – Normally Open) A Normally Open (N.O.) sensing input point for controlling of the Output 1, with this terminal connecting to (-) ground, the Egress Button and the whole group of Users (PINs & Cards) for Output 1 are disabled. It is prepared mainly for the cross wire connection with the “Inter-lock O/P” point on the associated controller in an Inter-lock system.
16 - 17 - 18: OUTPUT 2 -- (Output Relay 2) 1 Amp relay dry contact controlled by the Group 2 User Code & Cards. It is an auxiliary output ideally for controlling of security system or automatic operator. Terminal 16 is Normally Closed contact (N.C.), terminal 18 is Normally Open contact (N.O.) and terminal 17 is the common point of the two contacts. The operation time of Output 2 is programmable from the keypad (with Function Jumper on position 1). See programming Location 52 for the details.
10. SETTING UP A SPLIT-DECODED KEYPAD SYSTEM Power Supply of The System DK-2800 MK-II keypads consist of 12V/DC, 12-24V/DC and 12-24V AC/DC operation voltages. Please check the operation voltage of your keypad before applying power to it. • In split-decoded operation, the keypad system MUST be DC operation. AC operation is not allowed. • For keypads of 12V/DC operation, both keypad and split-decoder are required to operate at 12V/DC.
Jumper Setting for Link-up Procedures It is necessary to send the Master Code (the link-up code) of the keypad to the decoder for it to recognize the keypad working with it. The decoder will refuse other keypad that is not registered. The keypad will generate warning beep continuous once per second if link-up is unsuccessful. Link-up Procedures: • Put the “Link-up Jumper” from OFF to ON position (the jumper is located on the main circuit board next to the connection terminals).
4) Door Open Alarm (Designed for Emergency Door): • The Door Open Alarm is enabled by programming from keypad at Programming Location 91 • Alarm Output and Internal Siren activate • Alarm happens in door forced to open or normal open with Egress Button • No Alarm happens in door open with User Code or Card 5) Door Forced Open Alarm: • The Door Forced Open Alarm is enabled by programming from Keypad at Programming Location 80 • Alarm Output and Internal Siren activate • Alarm happens in door forced to open o
11. PREPARATION FOR PROGRAMMING a) CRITERIA FOR CODES AND CARDS Prime Codes The prime codes include the a) User Codes, b) Master Code, c) Duress Codes, d) Super User Codes, e) Common User Codes and f) Visitor Codes. All these codes MUST be unique. It is not allowed to repeat a prime code for second function. All the codes in this system can be 4-8 digits for Manual Entry Mode. The codes must be in the same digit length with the Master Codes for Auto Entry Mode. See Location 70 for the details.
EM Card + Group Secondary User Code – Operation Media 3 A secondary user code can be repeatedly used for a group of cards in a department. Owner can make a proprietary department code for each department in a company. Only the staff of the department holding a card and knowing the code is accepted to enter. This approach increases the departmental security and prevents a lost card picked up by other group of people in the company to open the door.
12. PROGRAMMING & OPERATION a) POWER-UP THE KEYPAD The keypad gives power-up delay of 1 minute after power has been applied. It is the time frame designed for setting the keypad to programming mode with DAP code. See the details of “DAP CODE – 2 8 2 8” below. 1. The keypad gives continuous beeps for 1 minute after power-up. 2. The power-up delay can be stopped instantly with 12# if the delay beep is found annoying and setting the keypad to programming mode with DAP code is not required.
4. Key in the DAP code 2828 and validate it with * *. The Status LED is ON and the keypad is in programming mode like using Master Code. It is ready to accept new programming data as long as you like until exit programming mode. DAP CODE 2828 VALIDATION → ** 5. To program a new Master Code to replace the old one. See “Record A Master Code” stated at “Location 01” for the details.
LOCATION PARAMETERS DEFAULT FUNCTIONS & VALUES 56 Start & Stop Time Nil ----- User Program Required 60 Personal Safety & Lock-out Code = 1, 10 False Code/Card Lock-out 60 Sec 70 User Code Entry Mode Code = 2, Manual Entry Mode 71 Pacifier Tones ON-OFF Selection Code = 1, Pacifier Tone ON 72 O/P Operation Announcer Code = 1 Sec, Notification Beep ON 73 Status LED Standby Flashing ON-OFF Code = 1, Flashing Enabled 80 Door Forced Open Warning & Timing Code = 0, Warning Disabled 81 Door
14. SUPER USER CODE -- Location 02 The Super User Code has TWO functions. It is prepared to operate the three outputs and make operation of inhibit enable / disable to those outputs. LOCATION 02 (1) → SUPER USER CODE 4 to 8 DIGITS (2) → VALIDATION # (3) (1) LOCATION • Key in Location 02 (2) SUPER USER CODE • The Super User Code can be 4 to 8 digits. • When a new Super User Code is keyed in and confirmed, the old one is replaced. (3) VALIDATION • Pressing # key to confirm code entry.
The door is un-locked while the function is enabled. Do not forget to stop this function after use because the door is un-locked. Also, the system refuses the optional functions (3) & (4) while Override function comes into effect. This feature is good for all the “Fail-safe electric locks”. “Fail-secure electric lock” requires power to keep in un-locked condition. It takes high current all the time while the function comes into effect and may cause damage to it.
15. COMMON USER CODES FOR OUTPUT 1, 2 & 3 -Locations 03, 04, & 05 The Common User Codes 1, 2 and 3 are prepared for operating of the Output 1, 2 and 3 respectively as an enhance code. The Common User Codes MUST work in the form of “Card + Common Code” to operate the outputs to increase the security of the access control system. See Media 4 at Locations 10, 20 & 30 for more information. Common User Code alone can NOT operate the Outputs directly.
16. USER CODES / CARDS FOR OUTPUT 1, 2 & 3 -Locations 10, 20 & 30 Total 1,200 User Codes / Cards are available for controlling of the three outputs.
EXAMPLES – PROGRAMMING AND OPERATION Example 1 -- EM Card Only: Programming: 10 1 001 (a) (b) (c) (a) The card is programmed for operating Output 1 READ CARD (d) # (e) (b) The operation medium is EM Card only (c) Take ID number 001 in Group 1 to store the card, which is one of the IDs in 000-999 (d) Put the card close to the reader, one beep confirms the reading (e) Press # to store the “Card”, two-beep confirms a valid entry Operation: (while the system is back to operation mode) READ CARD (a) (a)
(a) The card is programmed for operating Output 1 (b) The operation medium is EM Card + Secondary User Code (c) Take the ID number 002 in Group 1 to store the Card & Code, which is one of the IDs in 000-999 (d) Put the card close to the reader.
(a) Key in the User Group that the User ID belongs to. “10” for Group 1, “20” for Group 2, and “30” for Group 3 (b) Key in “5” that is the Command Code for making a deletion (c) Key in the User ID that stored the User Code, the lost EM card or the EM Card+User Code (d) Press the # key. Two-beep confirms a valid entry and the Code and/or Card in that User ID is cleared Delete an EM Card READ CARD 5 # (a) (b) (c) (d) (a) Key in the User Group that the EM Card belongs to.
17. VISITOR CODES (FOR OUTPUT 1 ONLY) -- Location 40 The Visitor Codes are temporary user codes for Output 1 (mainly for door strike in access control). They can be programmed as “One Time Codes” or “Codes with Time Limit”. The Visitor Codes will be cleared automatically after use if they are one time codes, or, when the allowed time expires.
EXAMPLES: Example 1: Set a “One Time Visitor Code” with the number of “1 2 6 8” for the Output 1 40 01 00 1268 # (a) (b) (c) (d) (e) (a) Visitor Code Programming, (b) The Visitor ID, (c) An One Time Code, (d) The Visitor Code, (e) Entry Confirmation Example 2: Set a “Visitor Code” with the number of “1 3 7 8” that is valid for three hours 40 02 03 1378 # (a) (b) (c) (d) (e) (a) Visitor Code Programming, (b) The Visitor ID, (c) Valid for 3 Hours, (d) The Visitor Code, (e) Entry Confirmation Examp
18. DURESS CODES (FOR OUTPUTS 1, 2 & 3) -Locations 41, 42 & 43 Duress Codes are prepared for those Important Persons in case of DURESS while he is operating the access control keypad. The duress code operates like a normal User Code for Output 1, 2 or 3, and at the same time activates the Duress Output without any indication.
EXAMPLES: Example 1: Set a “Duress Code” with the number of “3 3 6 9” for Output 1 41 01 3369 # (a) (b) (c) (d) (a) Duress Code for Output 1, (b) Duress Code ID, (c) The Duress Code, (e) Entry Confirmation Example 2: Set a “Duress Code” with the number of “2 3 9 8 0” for Output 2 42 01 23980 # (a) (b) (c) (d) (a) Duress Code for Output 2, (b) Duress Code ID, (c) The Duress Code, (e) Entry Confirmation Example 3: Delete an Output 1 “Duress Code” from Duress Code ID 01 in the memory 41 01 # (a) (
Operation: Taking Duress Code 3 3 6 9 in Group 1 for Output 1 As Example READ CARD 3369 # (a) (b) (c) a) Read the EM card. Two-beep confirms the reading and 30 seconds waiting time is given for the entry of Duress Code, the Amber LED keeps flashing b) Key in the Duress Codes 3 3 6 9 for operating Output 1 c) Confirm it with the # key. Output 1 activates in a normal way and the Duress Output also activates to report Duress Event to an alarm system if connected.
RESET OUTPUT TIMER WITH SUPER USER CODE The Output Timer can be RESET manually at anytime with the Super User Code that operates the desired output before the end of the time. Example: Reset Output 1 Timer -- SUPER USER CODE #1 ------------- Output 1 stops Reset Output 2 Timer -- SUPER USER CODE #2 ------------- Output 2 stops Reset Output 3 Timer -- SUPER USER CODE #3 ------------- Output 3 stops 20.
The real-time-clock stops after power failure, which makes the real-time inhibition loses its time base. It is necessary to re-program the system’s real-time-clock unless the keypad is back up with UPS. The keypad gives warning beeps of 3 fast beeps / 5 seconds continuously after power failure until the real-time-clock is re-programmed. No after “power failure warning beep” will be given if Location 56 is not programmed with Start/Stop times.
Programming and Operation Examples: Set the starting and stopping time for the real-time inhibition period a) Set Inhibition Period from 12:30 PM (today) – 1:30 PM (today) for lunch time: 56 1230 1330 # b) Set Inhibition Period from 6:30 PM (today) – 8:15 AM (next day) for office close: 56 1830 0815 # The start and stop time figures are 24 hours basis. They are 4-digit figures from the smallest 00:00 to the largest 23:59.
22. PERSONAL SAFETY AND SYSTEM LOCK-UP -Location 60 LOCATION 60 (1) → LOCK-UP OPTIONS 1 to 2 DIGITS (2) → VALIDATION # (3) (1) LOCATION Key in Location 60 (2) LOCK-UP OPTIONS The Options are represented by the following Numbers. They are described below: 1 --- After 10 successive false Card/User Code trials, the keypad locks during 60 seconds. -- (Default) 2 --- After 10 successive false Card/User Code trials, activates the Duress output to switch to (-) ground.
1 --- Auto Entry Mode Auto Entry Mode requires no pressing of the # key after code entry for code checking. In the Auto Entry Mode, the User Codes MUST be set in the same digit length of the Master Code (For example, if the Master Code is 5 digits, then all User Codes must be in 5 digits as well. All other User Codes not in 5 digits become invalid). When the number of digits reaches, the system will check the User Code automatically. Good for high traffic access control.
25. OUTPUT OPERATION ANNOUNCER -- Location 72 LOCATION 72 (1) → FUNCTION MODES 1 or 0 (2) → VALIDATION # (3) (1) LOCATION Key in Location 72 (2) FUNCTION MODES FOR OUTPUT ANNOUNCER Output announcer gives notification beep on the operation status of the outputs. There are two notification modes available for the selection.The notification is also OFF while the Pacifier Tone OFF mode in the Location 71 is selected.
1 --- Standby Flashing ON -- (Default) The Status LED gives Standby Flashing all the time. It also gives the light indications showing the operation status of the system. 0 --- Standby Flashing OFF The Standby Flashing is OFF but it does not affect the system status indications. (3) VALIDATION Press # key once. Two-beep confirms the entry. 27.
28. DOOR PROPPED-UP WARNING & THE DELAY TIME -- Location 81 LOCATION 81 (1) → FUNCTION MODES 0 or 1 - 999 (2) → VALIDATION # (3) (1) LOCATION Key in Location 81 (2) FUNCTION MODES FOR DOOR PROPPED-UP WARNING If somebody opened the door and left it open longer than the allowable delay time, the keypad will generate door propped-up warning until the door is re-closed. There is warning beeps from the keypad only but it does not activate the alarm output.
WHERE AND WHY “GOING OUT” NEEDS ATTENTION Examples for some areas may need an Intelligent Egress Button: Hospital: Some of the patients are not allowed to leave the ward without doctor’s permission. An egress button with exit delay and warning beeps will help the nurse or warden to get attention to the door when the egress button is pressed. Further setting of the egress button with holding contact delay even gives higher level of security to a controlled door.
29. EGRESS DELAY, WARNING AND ALARM -- Location 90 LOCATION 90 (1) → CONFIGURATIONS 1-6 (2) → DELAY TIME VALIDATION (3) (4) 0 or 1 - 99 → # (1) LOCATION Key in Location 90 (2) CONFIGURATIONS OF THE EGRESS WARNING AND ALARM Key in the number to enable 1 of the 6 configurations described below: 1 --- Momentary Contact Mode without Warning -- (Default) • Press the Button once. No warning or alarm is given during Egress Delay. • Good for silent area.
(3) EGRESS DELAY TIMER 0 --- No Delay – (Default) Output 1 activates instantly (the door is released instantly) when the Egress Button is pressed. 1 – 99 --- Egress Delay Timing Put a number of 1 to 99 into the box to enable the Egress Delay. The number is the time in second, which starts to count when the Egress Button is pressed. Output 1 activates (the door is released) when the delay time reaches. • Momentary Contact -- The Egress Delay starts to count when the egress button is momentarily pressed.
30. DOOR OPENING ALARM & TIMER -- Location 91 LOCATION 91 (1) → ALARM TIME VALIDATION (2) (3) 0 or 1 - 999 → # (1) LOCATION Key in Location 91 (2) ALARM & TIMING OF DOOR OPENING 0 --- No Alarm – (Default) The Alarm Output is disabled 1 - 999 --- Alarm Timer The Door Open Alarm operates the Alarm Output (Terminal 23) only. It is mainly prepared to trigger an optional alarm system. Put a Timing Figure of 1 to 999 into the box to enable the function of Door Opening Alarm.
31. WIEGAND DATA OUTPUT MODES -- Location 92 This features is only available to the keypads with Wiegand Data Output. LOCATION 92 (1) → DATA OUTPUT MODES → 1, 2, 3 or 4 (2) VALIDATION # (3) (1) LOCATION Key in Location 92 (2) DATA OUTPUT MODES 1 --- Wiegand Data Output Disabled (Default) No Wiegand data output 2 --- Wiegand Data Output Enabled -- Mode “A” The keypad gives Wiegand data output ONLY for those cards and codes that have been registered in memory.
32. WIEGAND DATA OUTPUT FORMAT -- Location 93 This features is only available to the keypads with Wiegand Data Output. LOCATION 93 (1) → WIEGAND FORMAT VALIDATION → 1, 2 or 3 # (2) (3) (1) LOCATION Key in Location 93 (2) WIEGAND FORMAT FOR EM CARD & USER CODE The Wiegand data output is programmable for 26-bit, 34-bit or 37-bit standard format.
33. OPERATION MODES -- Location 94 The keypad is programmable for keypad mode to work stand-alone for door control directly or for server mode to work with a split-decoder for high security access control. LOCATION 94 (1) → OPERATION MODES VALIDATION → 0 or 1 # (2) (3) (1) LOCATION Key in Location 94 (2) OPERATION MODES 0 – Keypad Mode (Default) Keypad Mode sets the keypad for stand-alone operation to provide its available functions.
35. PROGRAMMING MAKE SIMPLE – FOR GENERAL USERS Split-decoded keypad is multi purpose keypad. It has many functions for user’s selection. For those general users taking the keypad for door strike only, most of the features can be kept in their Default values. Only the User Codes / Cards and a private Master Code are required to program. The keypad accepts 1) Card only, 2) Code only, 3) Card + Code or 4) Card + Common User Code to operate its outputs.
5) Record an “EM Card + User Code” to Operate The Output 1 for Door Open 10 3 READ CARD (d) 003 (a) (b) (c) (a) 10 = Programming Location for Output 1 6123 (e) # (f) (b) 3 = Programming option for EM Card + User Code. (The User Code can be repeated use or proprietary) (c) 003 = One of the 1,000 User IDs for the User Code/Card from 000-999 (d) Read Card = Put the Card close to the card reader (e) 6123 = The User Code to be used with the EM Card. It is for example here only.
36. WIEGAND OUTPUT FORMATS FOR ADVANCED KEYPADS The Timing and Electrical Manner of The Wiegand Data Output Wiegand is a common medium in the communication between readers and controller in access control. The Wiegand data from the keypad unit provides a level of compatibility for readers and controller that can be used by consultants in custom project development. The Wiegand interface uses three wires, one of which is a Common Ground and two of which are data transmission wires called DATA 0 and DATA 1.
26 Bit Wiegand Data From EM Cards 26-bit EM Card is the most popular one on the market. Almost all the controllers can use the 26-bit standard format. A 26 bit Wiegand protocol for card reading has 1 first parity bit, 24 bits of the Card ID, and 1 stop bit for a total of 26 bits. The first parity bit is an Even parity bit calculated from the first 12 bits of the code and the trailing parity bit is an Odd parity bit from the last 12 bits. The data transmitted is in Hex Binary codes.
Precaution 2 The HEX code of Wiegand data is derived from the user code. Do NOT make an user code starting with “0”, such as 02345. Otherwise it will cause confusion in Hex code with the user code in same number without “0” at the front. Please see examples B & C below for the explanations. This precaution applies to 26-bit, 34-bit and 37-bit Wiegand data. Example A shows a 34-bit Wiegand data derived from an 8-digit User Code 12345678.
37.
FUNCTION ENTRY LIMITS & CODE OPTIONS 60 Personal Safety & Lock-Up LOCK-UP CODE: 1---10 Trial, Lock-Up 60 Sec.
FUNCTION ENTRY LIMITS & CODE OPTIONS CODE ENTRY FACTORY DEFAULT *9 2 Wiegand Data Output Mode DATA OUTPUT MODE 1 --- W iegand Data Output Disabled 2 --- W iegand Data Output Enabled -- Mode “A” 3 --- W iegand Data Output Enabled – Mode “B” 4 --- W iegand Data Output Enabled – Mode “C” 92 DATA OUTPUT MODE # Mode = 1 Disabled *9 3 Wiegand Data Output Format Mode DATA OUTPUT MODE 1 --- 26-Bit Wiegand Data 2 --- 34-Bit Wiegand Data 3 --- 37-Bit Wiegand Data 93 WIEGAND FORMAT # Format = 1 26
38. APPLICATION EXAMPLES a) BASIC WIRINGS OF A SPLIT-DECODED ACCESS CONTROL DOOR LOCK Description Split-decoded keypad provides overall higher security than the stand alone keypad. It consists of a server keypad unit installing outside for human interface and a decoder unit installing inside the house for all the input / output wire installations. The two units are linking up with the Data I/O bus.
Wiring Diagram LINK UP 12-24V DC POWER SUPPLY TAMPER N.C OUTPUT 1 N.C. AD-1312 OR AP-960 -ALARM O/P -KEY ACT O/P -N.O. -COM -N.C. -N.O. DATA I/O -COM -N.C. -N.O. -COM -N.C. -TAMPER -GND(-) (+) (–) 12-24V DC -DOOR SENS -O/P 1 INHIB -INT. LOCK -DU OUT -DOOR BELL IN Any DK-2800 MK-II Keypad THE SERVER KEYPAD -EG IN -DATA I/O -KEYPAD PWR -GND(-) -12-24V DC DA-2800 OR DA-2801 (DECODE) OUTPUT 2 N.O. OUTPUT 3 OUTPUT RELAY 1 N.O. Output for Fail-secure Lock N.C.
System Connection DATA I/O BUS (+) POWER SUPPLY (–) COMMON GND ELECTRIC LOCK AR-2802/06/07 AUXILIARY READER OR KEYPAD-READER Any DK-2800 MK-II Keypad THE SERVER KEYPAD DA-2800 OR DA-2801 (DECODER) Wiring Diagram DA-2800 OR DA-2801 (DECODER) LINK UP N.C. AD-1312 OR AP-960 OUTPUT 2 N.O. - ALARM O/P - KEY ACT O/P - N.O. - COM - N.C. 12-24V DC POWER SUPPLY TAMPER N.C - N.O. DATA I/O OUTPUT 1 - COM (+) (–) 12-24V DC - N.C. - N.O. - COM LED - N.C.
System Connection DATA I/O DATA I/O (+) (–) (+) (–) DA-2800 DA-2800 ELECTRIC LOCK THE SERVER Any DK-2800 MK-II Keypad INT-LOCK O/PI INHIBIT Split-Decoder Split-Decoder O/PI INHIBIT THE SERVER Any DK-2800 MK-II Keypad ELECTRIC LOCK DA-2801 CROSS WIRE CONNECTION INT-LOCK DA-2801 Wiring Diagram DATA I/O (+) (–) 12-24V DC THE SERVER KEYPAD Any DK-2800 MK-II Keypad TAMPER N.C DATA I/O (+) (–) 12-24V DC THE SERVER KEYPAD Any DK-2800 MK-II Keypad TAMPER N.
39. APPLICATION HINTS FOR THE AUXILIARY TERMINALS (A-1) TAMPER N.C. THE DECODER OR ALARM SYSYEM TAMPER SWITCH OF THE KEYPAD TAMPER N.C. The tamper switch is Normally Closed while the keypad is secured on gang box. It is open when the keypad is removed from the gang box. To prevent sabotage, connect these terminals in series with a 24 hour N.C. protection zone of an alarm system or the temper input terminal of the decoder. GND(–) (A-2) TAMPER N.C. TAMPER N.C. TAMPER SWITCH KEYPAD 1 N.C.
(C) ALARM OUTPUT ALARM O/P KEY ACT O/P GND (-) OR LED LOW POWER PIEZO BUZZER ALARM O/P KEY ACT O/P ALARM CONTROL PANEL 24 HOUR N.O. PROTECTION ZONE GND (-) The Alarm Output switches to (-) ground in door forced to open or the door open after Egress Delay. You may use it to turn ON an LED lamp and/ or a small buzzer to notify a guard; or connect it to a 24 hour Normally Open protection zone of an alarm system. See Location 80 and Location 91 for more information about these functions.
(E) DURESS OUTPUT ALARM CONTROL PANEL OR LED LOW POWER PIEZO BUZZER 24 HOUR N.O. PROTECTION ZONE The Duress Output switches to (-) ground when duress code is entered. You may use it to turn ON an LED lamp and/ or a small buzzer to notify a guard; or connect it to a 24 hour Normally Open protection zone of an alarm system. • Only one connection option is recommended. Make sure that the sink current does not exceed the maximum rating of 100mA. 40.
Connection Terminal 4 5 6 7 LED BUZ 8 9 10 WIEGAND D0 D1 RS 232 WIEGAND D0 D1 3 9 2 DATA I/O TAMPER N.C. 7 (+) (–) 12-24V DC BUZ 8 1 1 Version "A" ONLY 2 (+) (–) 12-24V DC 3 DATA I/O 4 5 TAMPER N.C. Version "A" ONLY RS 232 AR-2806 10 AR-2802 and AR-2807 6 LED 41. AUXILIARY INFORMATION • DRY CONTACT A dry contact means that no electricity is connected to it. It is prepared for free connections. The Relay Output contacts provided in this keypad system are dry contacts.
42. TECHNICAL DATA For technical data please refer to Part 1 of these operating instructions.
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com). All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in electronic data processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited. This publication represent the technical status at the time of printing. Copyright 2018 by Conrad Electronic SE.
